-
ISDN Einwahl
Hi Leute
Ich will einen Pentium 90 als Proxy und Firewall einrichten. In dem Rechner steckt eine AVM Fritz PCI. Die Einrichtung unter Yast1 funktioniert (glaub ich). Die Test verlaufen richtig und ich speichere das ganze dann ab. Wenn ich dann ipppd ausführe steht da : no devices found.
ifconfig:
ippp0 Link encap:Point-to-Point Protocol
inet addr:192.168.243.89 P-t-P:192.168.0.1 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:30
Was mach ich falsch ? Wie wähle ich mich richtig ein ?
Was ist die DNS der T-Online ?
-
Ich hab beim Reboot noch was entdeckt:
failed services in runlevel 2:i4l_hardware i4l
-
Komisch, nach dem reboot war die isdn-Karte bei ifconfig weg
Yast gestartet, ISDN-Hardware konfig., Starten: Fehler, nochmal starten
folgendes:
Loading ISDN drivers ...
Loading HiSax driver ...
/sbin/insmod /lib/modules/2.2.10/net/slhc.o
/sbin/insmod /lib/modules/2.2.10/misc/isdn.o
/sbin/insmod /lib/modules/2.2.10/misc/hisax.o id=Fritz type=27
protocol=2
Verbose-level set to 3.
Starting isdnlog with /etc/isdn/isdnlog.isdnctrl0.options for
isdnctrl0...
Speichern, und die Karte ist wieder da (ifconfig).
-
Hier ist vielleicht noch eine kleine Hilfe. Hab ich aus der /var/log/messages:
Jul 20 13:57:24 linux kernel: HiSax: Version 3.2a (module)
Jul 20 13:57:24 linux kernel: HiSax: Layer1 Revision 2.34
Jul 20 13:57:24 linux kernel: HiSax: Layer2 Revision 2.17
Jul 20 13:57:24 linux kernel: HiSax: TeiMgr Revision 2.12
Jul 20 13:57:24 linux kernel: HiSax: Layer3 Revision 2.9
Jul 20 13:57:24 linux kernel: HiSax: LinkLayer Revision 2.29
Jul 20 13:57:24 linux kernel: HiSax: Approval certification failed because of
Jul 20 13:57:24 linux kernel: HiSax: unauthorized source code changes
Jul 20 13:57:24 linux kernel: HiSax: Total 1 card defined
Jul 20 13:57:24 linux kernel: HiSax: Card 1 Protocol EDSS1 Id=Fritz (0)
Jul 20 13:57:24 linux kernel: HiSax: AVM PCI driver Rev. 1.9
Jul 20 13:57:24 linux kernel: AVM PCI: stat 0x3020a
Jul 20 13:57:24 linux kernel: AVM PCI: Class A Rev 2
Jul 20 13:57:24 linux kernel: HiSax: AVM Fritz!PCI config irq:9 base:0xFF40
Jul 20 13:57:24 linux kernel: AVM PCI: ISAC version (0): 2086/2186 V1.1
Jul 20 13:57:24 linux kernel: AVM Fritz PnP/PCI: IRQ 9 count 0
Jul 20 13:57:24 linux kernel: AVM Fritz PnP/PCI: IRQ 9 count 3
Jul 20 13:57:24 linux kernel: HiSax: DSS1 Rev. 2.14
Jul 20 13:57:24 linux kernel: HiSax: 2 channels added
Jul 20 13:57:24 linux kernel: HiSax: MAX_WAITING_CALLS added
Jul 20 13:57:25 linux kernel: HiSax: debugging flags card 1 set to 4
Jul 20 13:57:25 linux kernel: isdn: Verbose-Level is 3
Jul 20 13:57:26 linux isdnlog: isdnlog Version 3.41 starting
Jul 20 13:57:26 linux isdnlog: isdnlog Version 3.41 starting
Jul 20 13:57:26 linux isdnlog: Warning: no holiday database specified!
Jul 20 13:57:26 linux isdnlog: Warning: no country database specified!
Jul 20 13:57:26 linux isdnlog: Warning: no rate database specified!
Jul 20 13:57:26 linux isdnlog: (ISDN subsystem with ISDN_MAX_CHANNELS > 16 detec
ted - 2 active channels, 2 MSN/SI entries)
Jul 20 13:57:26 linux isdnlog: (Data versions: iprofd=0x05 net_cfg=0x05 /dev/i
sdninfo=0x01)
Jul 20 14:00:20 linux in.telnetd[376]: connect from 192.168.243.201
Jul 20 14:00:26 linux login: pam_unix session started for user root, service log
in
Jul 20 14:00:42 linux YaST[232]: Started the SuSE-Configuration Tool.
Jul 20 14:00:42 linux yast[232]: Skipping new package checks.
Jul 20 14:00:42 linux yast[232]: Reading /etc/rc.config and updating the system.
..
Jul 20 14:02:42 linux modprobe: modprobe: Can't locate module ippp0
Jul 20 14:02:44 linux ipppd: info: no CHAP secret entry for this user!
Jul 20 14:02:44 linux ipppd[853]: Found 1 device: /dev/ippp0
Jul 20 14:02:44 linux kernel: ippp, open, slot: 0, minor: 0, state: 0000
Jul 20 14:02:44 linux kernel: ippp_ccp: allocating reset data structure
Jul 20 14:02:44 linux ipppd[860]: ipppd i2.2.10 (isdn4linux version of pppd by M
H) started
Jul 20 14:02:44 linux ipppd[860]: init_unit: 0
Jul 20 14:02:44 linux ipppd[860]: Connect[0]: /dev/ippp0, fd: 15
Jul 20 14:04:11 linux ipppd: info: no PAP secret entry for this user!
Jul 20 14:04:11 linux ipppd: info: no CHAP secret entry for this user!
Jul 20 14:04:11 linux ipppd[870]: Exit.
Jul 20 14:05:56 linux ipppd[860]: Terminating on signal 15.
Jul 20 14:05:56 linux ipppd[860]: closing fd 15 from unit 0
Jul 20 14:02:44 linux ipppd[860]: init_unit: 0
Jul 20 14:02:44 linux ipppd[860]: Connect[0]: /dev/ippp0, fd: 15
Jul 20 14:04:11 linux ipppd: info: no PAP secret entry for this user!
Jul 20 14:04:11 linux ipppd: info: no CHAP secret entry for this user!
Jul 20 14:04:11 linux ipppd[870]: Exit.
Jul 20 14:05:56 linux ipppd[860]: Terminating on signal 15.
Jul 20 14:05:56 linux ipppd[860]: closing fd 15 from unit 0
Jul 20 14:05:56 linux ipppd[860]: link 0 closed , linkunit: 0
Jul 20 14:05:56 linux ipppd[860]: Exit.
Jul 20 14:06:00 linux ipppd: info: no CHAP secret entry for this user!
Jul 20 14:06:00 linux ipppd[997]: Found 1 device: /dev/ippp0
Jul 20 14:06:00 linux kernel: ippp, open, slot: 0, minor: 0, state: 0000
Jul 20 14:06:00 linux kernel: ippp_ccp: allocating reset data structure
Jul 20 14:06:00 linux ipppd[1002]: ipppd i2.2.10 (isdn4linux version of pppd by
MH) started
Jul 20 14:06:00 linux ipppd[1002]: init_unit: 0
Jul 20 14:06:00 linux ipppd[1002]: Connect[0]: /dev/ippp0, fd: 15
Jul 20 14:21:27 linux isdnlog: (HiSax driver detected)
Jul 20 14:21:34 linux isdnlog: Jul 20 14:21:33 tei 72 calling ? with ? HANGUP (
0:00:06)
Jul 20 14:21:52 linux isdnlog: Jul 20 14:21:52 tei 72 calling ? with ? Time:INV
ALID - ignored
Jul 20 14:21:52 linux isdnlog: Jul 20 14:21:52 tei 72 calling ? with ? CONNECT
-
Hallo dschwan!
Die DNS der T-Online ist 194.25.2.129.
Probier es mal mit kisdn, das macht die Einstellung automatisch.
Als Benutzernamen musst du Anschlußkennung, T-Online Nr. und die Mitbenutzersuffix eintragen (zwischen T-Online Nr. und Mitbenutzersuffix musst du eine Raute (#) schreiben z.B. 12345612345#1)
Als Kennwort dein normales T-Online Passwort.
Wenn die Einstellungen fertig sind musst du noch folgendes eingeben:
init 1 [Enter]
init 2 [Enter] wenn du auf die Konsole willst, bzw. init 3 [Enter] für KDE (bzw andere Windows-Manager).
Tschüss!
Hoffentlich konnte ich dir helfen!
-
Hallo!
Ich weiß nicht oib es der Fehler ist, aber bei mir war es so. ich habe erst einmal pnpdump reinhauen müssen, dann neu starten und und yast die isdn geschichte einrichten müssen. Das ist nur notwendig, wenn du eine PnP Karte hast
Ronald
Berechtigungen
- Neue Themen erstellen: Nein
- Themen beantworten: Nein
- Anhänge hochladen: Nein
- Beiträge bearbeiten: Nein
-
Foren-Regeln
Lesezeichen