Plextor PX-W2410A mit Suse8.1

[joda]

Tach,
Ich habe ein problem mit dem brennen mit meinem Plextor PX-W2410A.
Der brenner wird ohne probleme zwar erkannt und scsi auch emuliert. Etwas komisch ist schon das mein dvd laufwerk und der brenner ziemlich oft in der emulation vorkommen.
Doch wenn ich jetzt probiere mit cdrado eine cd zu brennen meint dieses programm immer das die cd die eingelegt ist bereits beschrieben sei obwohl dies nicht möglich sein kann weil ich mehere cds ausprobiert habe.
cdrecord behauptet auch das die cd nicht leer sei doch kann ich mit erzwingen (in k3b) den schreibvorgang starten der dann auch durschgeführt wird!
Außerdem kann ich seit dem ich den brenner eingebaut habe (dvd hängt als slafe am gleichen kabel) kann ich das dvd nicht mehr normal mit mount /media/dvd mounten. Es kommt immer:
/dev/dvd: Eingabe-/Ausgabefehler
mount: Sie müssen den Dateisystemtyp angeben
Obwohl en der fstab als dateityp auto steht. Desweiteren wird der dvd auch nicht im kde im desktop angezeigt!

Kann es vielicht daran liegen das das board so neu ist? Gigabyte GA-7VAXP
Oder woran könnte das liegen?

[Spike05]

Gib mal die Ausgabe von

cdrecord -scanbus

an

cu

Jochen

[joda]

Cdrecord 1.11a28 (i686-suse-linux) Copyright (C) 1995-2002 Jörg Schilling
Linux sg driver version: 3.2.0
Using libscg version 'schily-0.6'
scsibus0:
0,0,0 0) 'PLEXTOR ' 'CD-R PX-W2410A' '1.04' Removable CD-ROM
0,1,0 1) 'TOSHIBA ' 'DVD-ROM SD-M1612' '1004' Removable CD-ROM
0,2,0 2) *
0,3,0 3) *
0,4,0 4) *
0,5,0 5) *
0,6,0 6) *
0,7,0 7) *

[Spike05]

Hmm, ich dachte es tritt eine andere Ausgabe auf! Nämlich das dein Brenner mehrfach erkannt wird!

cu

Jochen

[joda]

wird er auch nur nicht bei cdrecord sondern bei den anderen programmen und beim hochfahren auch.
Das steht in der boot.msg

<4>VP_IDE: chipset revision 6
<4>VP_IDE: not 100%% native mode: will probe irqs later
<6>VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
<4> ide2: BM-DMA at 0xe000-0xe007, BIOS settings: hdeMA, hdfio
<4> ide3: BM-DMA at 0xe008-0xe00f, BIOS settings: hdgMA, hdhMA
<4>hde: WDC WD1200JB-00DUA0, ATA DISK drive
<4>hdg: PLEXTOR CD-R PX-W2410A, ATAPI CD/DVD-ROM drive
<4>hdh: TOSHIBA DVD-ROM SD-M1612, ATAPI CD/DVD-ROM drive
<4>ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>ide3 at 0x170-0x177,0x376 on irq 15
<4>blk: queue c039cfbc, I/O limit 4095Mb (mask 0xffffffff)
<4>hde: safely enabled flush
<6>hde: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=14593/255/63, UDMA(100)
<4>ide-floppy driver 0.99.newide
<6>Partition check:
<6> hde: hde1 hde2 hde3
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<4>RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
<6>loop: loaded (max 16 devices)
8<6>Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
<6>Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
<4>ide-floppy driver 0.99.newide
<6>SCSI subsystem driver Revision: 1.00
<3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
<6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<6>IP: routing cache hash table of 4096 buckets, 32Kbytes
<6>TCP: Hash tables configured (established 32768 bind 65536)
<6>Linux IP multicast router 0.06 plus PIM-SM
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<5>RAMDISK: Compressed image found at block 0
<6>Freeing initrd memory: 226k freed
<4>VFS: Mounted root (ext2 filesystem).
<6>Journalled Block Device driver loaded
<4>hdg: no flushcache support
<4>hdh: no flushcache support
<6>scsi0 : SCSI host adapter emulation for IDE ATAPI devices
<4> Vendor: PLEXTOR Model: CD-R PX-W2410A Rev: 1.04
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: PLEXTOR Model: CD-R PX-W2410A Rev: 1.04
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: PLEXTOR Model: CD-R PX-W2410A Rev: 1.04
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: PLEXTOR Model: CD-R PX-W2410A Rev: 1.04
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: PLEXTOR Model: CD-R PX-W2410A Rev: 1.04
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: PLEXTOR Model: CD-R PX-W2410A Rev: 1.04
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: PLEXTOR Model: CD-R PX-W2410A Rev: 1.04
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: TOSHIBA Model: DVD-ROM SD-M1612 Rev: 1004
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: TOSHIBA Model: DVD-ROM SD-M1612 Rev: 1004
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: TOSHIBA Model: DVD-ROM SD-M1612 Rev: 1004
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: TOSHIBA Model: DVD-ROM SD-M1612 Rev: 1004
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: TOSHIBA Model: DVD-ROM SD-M1612 Rev: 1004
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: TOSHIBA Model: DVD-ROM SD-M1612 Rev: 1004
<4> Type: CD-ROM ANSI SCSI revision: 02
<4> Vendor: TOSHIBA Model: DVD-ROM SD-M1612 Rev: 1004
<4> Type: CD-ROM ANSI SCSI revision: 02

[Linrade]

Hi,

gegen das mehrfache Erkennen trägst Du "max_scsi_luns=1" in die /etc/lilo.conf appendzeile, bzw in die /boot/grub/menu.lst zu den Optionen ein. "/sbin/lilo -v" mußt Du noch ausführen, wenn Du lilo benutzt.

Das DVD lässt sich wieder mounten, wenn Du

ln -sf /dev/sr1 /dev/dvd
ln -sf /dev/sr1 /dev/cdrom
ln -sf /dev/sr0 /dev/cdrecorder

setzt.

[UdoJ]

Hi,habe sogar die gleiche Laufwerke wie du
Und fand die Lösung hier:
http://sdb.suse.de/de/sdb/html/81_ide-scsi.html
Gruß Udo

[joda]

jetzt kann ich das dvd wieder mounten und die devices werden auch nicht mehr doppelt erkannt
doch brennen kann ich immer noch nicht!
Der behauptet immer die cd wäre nicht leer... Dabei kann das überhaupt nicht sein denn ich habe mit dem brenner unter windows die gleichen rohlinge beschrieben ohne je irgendwelche probleme damit zu haben!
Am board sollte es auch nicht mehr liegen denn ich habe den via patch durschgeführt der nötig war um dma zu aktivieren. (GA-7VAXP)

[UdoJ]

Also,je nach dem an welchen Strang dein Brenner liegt must du z.b. hda=ide-scsi oder hdb=ide-scsi ect. im Grub mit eintragen.

Erst wenn die SCSI-Emulation Aktiv ist,kannst du brennen.
und welches Brenn Programm benutzt du??
Ich bekomme mit k3b auch nichts hin.
Gruß Udo

[joda]

das mit dem hdg=ide-scsi das hatte suse schon selber gemacht.
Ich benutzt k3b doch hatte ich das auch schonmal ohne k3b mit cdrado probiert wie es ja k3b auch nur macht!
Immer gleiche fehlermeldung cd sei nicht leer....

[Linrade]

Original geschrieben von joda
das mit dem hdg=ide-scsi das hatte suse schon selber gemacht.
Ich benutzt k3b doch hatte ich das auch schonmal ohne k3b mit cdrado probiert wie es ja k3b auch nur macht!
Immer gleiche fehlermeldung cd sei nicht leer....

Hi,

wohin zeigt /dev/cdrecorder?

ls -l /dev/cdr*

[joda]

/dev/cdrecorder -> sr0

[Linrade]

Hi,

dann "sollte" es eigentlich gehen. Gibt's Fehlermeldungen wenn Du brennen willst?

cdrecord [B]-vvV[/ B] ....

damit cdrecord etwas geschwätziger wird.
Schau auch mal in die /var/log/messages

> <4>hdg: no flushcache support
> <4>hdh: no flushcache support

Hmmm, woran hängen die beiden Laufwerke, was ist das für ein Controler?

Probier mal

flushb /dev/hdg && cdrecord -vvV ....


Wär doch gelacht

[joda]

Cdrecord 1.11a28 (i686-suse-linux) Copyright (C) 1995-2002 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.2.0
Using libscg version 'schily-0.6'
Using libscg transport code version 'schily-%M%-%I%'
atapi: 1

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cdrecord: Input/output error. test unit ready: scsi sendcmd: no error
CDB: 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 06 00 00 00 00 0A 00 00 00 00 28 00 00 00
Sense Key: 0x6 Unit Attention, Segment 0
Sense Code: 0x28 Qual 0x00 (not ready to ready change, medium may have changed) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.000s timeout 40s

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'inquiry' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 12 00 00 00 24 00
cmd finished after 0.000s timeout 40s
Inquiry Data : 05 80 00 21 5B 00 00 00 50 4C 45 58 54 4F 52 20 43 44 2D 52 20 20 20 50 58 2D 57 32 34 31 30 41 31 2E 30 34

Executing 'inquiry' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 12 00 00 00 60 00
cmd finished after 0.000s timeout 40s
Inquiry Data : 05 80 00 21 5B 00 00 00 50 4C 45 58 54 4F 52 20 43 44 2D 52 20 20 20 50 58 2D 57 32 34 31 30 41 31 2E 30 34 30 34 2F 32 35 2F 30 32 20 20 31 39 3A 30 30 20 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Inquiry Data : ...![...PLEXTOR CD-R PX-W2410A1.0404/25/02 19:00 ........................................

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 3F 00 00 00 00 00 08 00
cmd finished after 0.001s timeout 40s
Mode Sense Data 00 D0 00 00 00 00 00 00

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 02 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E
Mode Sense Data (converted) 3B

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 40 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E 00 00 00 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data (converted) 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Page Data 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 40 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E 00 00 00 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data (converted) 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Device type : Removable CD-ROM
Version : 0
Response Format: 1
Vendor_info : 'PLEXTOR '
Identifikation : 'CD-R PX-W2410A'
Revision : '1.04'
Device seems to be: Generic mmc CD-RW.

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 3F 00 00 00 00 00 08 00
cmd finished after 0.001s timeout 40s
Mode Sense Data 00 D0 00 00 00 00 00 00

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 02 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E
Mode Sense Data (converted) 3B

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 40 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E 00 00 00 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data (converted) 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Page Data 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 40 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E 00 00 00 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data (converted) 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 3F 00 00 00 00 00 08 00
cmd finished after 0.001s timeout 40s
Mode Sense Data 00 D0 00 00 00 00 00 00

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 02 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E
Mode Sense Data (converted) 3B

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 40 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E 00 00 00 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data (converted) 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Page Data 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 40 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E 00 00 00 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data (converted) 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 02 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E
Mode Sense Data (converted) 3B

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 40 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E 00 00 00 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data (converted) 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Page Data 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 40 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E 00 00 00 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data (converted) 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 02 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E
Mode Sense Data (converted) 3B

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 40 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E 00 00 00 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data (converted) 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Page Data 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 2A 00 00 00 00 00 40 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3E 00 00 00 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data (converted) 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0
Mode Sense Data 3B 00 00 00 2A 36 07 07 F3 7F 29 23 1B 90 01 00 10 00 1B 90 00 00 10 8A 10 8A 00 00 00 00 00 00 10 8A 00 06 00 00 10 8A 00 00 0D C8 00 00 0B 06 00 00 08 45 00 00 02 C2 00 00 00 B0

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 05 00 00 00 00 00 02 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3A
Mode Sense Data (converted) 37

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 05 00 00 00 00 00 3C 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3A 00 00 00 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Sense Data (converted) 37 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Sense Data 37 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Page Data 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 05 00 00 00 00 00 3C 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3A 00 00 00 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Sense Data (converted) 37 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Sense Data 37 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Mode Parameters (un-converted) 00 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Parameters 00 00 00 00 00 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Executing 'mode select g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 55 10 00 00 00 00 00 00 3C 00
cmd finished after 0.000s timeout 40s

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 05 00 00 00 00 00 02 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3A
Mode Sense Data (converted) 37

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 05 00 00 00 00 00 3C 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3A 00 00 00 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Sense Data (converted) 37 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Sense Data 37 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Page Data 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'mode sense g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 5A 00 05 00 00 00 00 00 3C 00
cmd finished after 0.000s timeout 40s
Mode Sense Data 00 3A 00 00 00 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Sense Data (converted) 37 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Sense Data 37 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Mode Parameters (un-converted) 00 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Parameters 00 00 00 00 00 00 00 00 05 32 01 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Executing 'mode select g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 55 10 00 00 00 00 00 00 3C 00
cmd finished after 0.000s timeout 40s

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Mode Parameters (un-converted) 00 00 00 00 05 32 00 05 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Parameters 00 00 00 00 00 00 00 00 05 32 00 05 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Executing 'mode select g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 55 10 00 00 00 00 00 00 3C 00
cmd finished after 0.000s timeout 40s

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Mode Parameters (un-converted) 00 00 00 00 05 32 02 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Mode Parameters 00 00 00 00 00 00 00 00 05 32 02 04 08 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Executing 'mode select g1' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 55 10 00 00 00 00 00 00 3C 00
cmd finished after 0.000s timeout 40s

[udo1]

hi
hast du es mal als root versucht?
mfg

udo