Hoi
Ich habe mir einen Promise Ultra 100 TX2 Controller eingebaut und habe and diesen Controller eine 40 GB IBM und eine 60 GB Maxtor Paltte angeschlossen. Der Controller erkennt die Platten am anfang sofort und richtig. Nur Linux net so rchtig ich hab mal meine boot.msg gepostet.
Ich habe Suse 8.0 drauf frisch installiert ohne irgendwas konfiguriert zu haben.
------------------------------------------------------------------------------------------
Inspecting /boot/System.map-2.4.18-4GB
Loaded 12771 symbols from /boot/System.map-2.4.18-4GB.
Symbols match kernel version 2.4.18.
Loaded 327 symbols from 20 modules.
klogd 1.4.1, log source = ksyslog started.
... 999.42 BogoMIPS
<4>Memory: 380260k/393152k available (1389k kernel code, 12504k reserved, 406k data, 120k init, 0k highmem)
<4>Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
<4>Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
<4>Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
<4>Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
<4>Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
<7>CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
<6>CPU: L1 I cache: 16K, L1 D cache: 16K
<6>CPU: L2 cache: 512K
<7>CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<7>CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
<7>CPU: Common caps: 0383f9ff 00000000 00000000 00000000
<4>CPU: Intel Pentium III (Katmai) stepping 03
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Checking 'hlt' instruction... OK.
<4>POSIX conformance testing by UNIFIX
<4>mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
<4>mtrr: detected mtrr type: Intel
<4>PCI: PCI BIOS revision 2.10 entry at 0xfb2d0, last bus=1
<4>PCI: Using configuration type 1
<4>PCI: Probing PCI hardware
<6>PCI: Using IRQ router VIA [1106/0596] at 00:07.0
<6>Activating ISA DMA hang workarounds.
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<6>apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
<5>apm: disabled on user request.
<4>mxt_scan_bios: enter
<4>Starting kswapd
<4>kinoded started
<5>VFS: Diskquotas version dquot_6.5.0 initialized
<5>ACPI: disabled by cmdline, exiting
<6>vesafb: framebuffer at 0xe6000000, mapped to 0xd880d000, size 4096k
<6>vesafb: mode is 1024x768x16, linelength=2048, pages=0
<6>vesafb: protected mode interface info at c000:02e5
<6>vesafb: scrolling: redraw
<6>vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
<6>Looking for splash picture..... found (1024x768, 42648 bytes).
<4>Console: switching to colour frame buffer device 105x34
<6>fb0: VESA VGA frame buffer device
<4>pty: 256 Unix98 ptys configured
<6>Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI SERIAL_ACPI enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>ttyS01 at 0x02f8 (irq = 3) is a 16550A
<6>Real Time Clock Driver v1.10e
<4>block: 128 slots per queue, batch=32
<4>RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
<6>Uniform Multi-Platform E-IDE driver Revision: 6.31
<4>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<4>VP_IDE: IDE controller on PCI bus 00 dev 39
<4>VP_IDE: chipset revision 6
<4>VP_IDE: not 100%% native mode: will probe irqs later
<6>VP_IDE: VIA vt82c596a (rev 07) IDE UDMA33 controller on pci00:07.1
<4> ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hdaio, hdb
<4> ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc
<4>PDC20268: IDE controller on PCI bus 00 dev 40
<6>PCI: Found IRQ 11 for device 00:08.0
<4>PDC20268: chipset revision 2
<4>PDC20268: not 100%% native mode: will probe irqs later
<4>PDC20268: ROM enabled at 0xe8000000
<4> ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde
<4> ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg
<4>hda: ST320410A, ATA DISK drive
<4>hdc: FX4820T, ATAPI CD/DVD-ROM drive
<4>hdd: WDC WD200BB-00CAA0, ATA DISK drive
<4>hde: IC35L040AVER07-0, ATA DISK drive
<4>hdf: MAXTOR 6L060J3, ATA DISK drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>ide1 at 0x170-0x177,0x376 on irq 15
<4>ide2 at 0xd800-0xd807,0xdc02 on irq 11
<4>blk: queue c031ece4, I/O limit 4095Mb (mask 0xffffffff)
<4>hda: safely enabled flush
<6>hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=2434/255/63
<4>blk: queue c031f1a4, I/O limit 4095Mb (mask 0xffffffff)
<4>hdd: safely enabled flush
<6>hdd: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63
<4>blk: queue c031f3c4, I/O limit 4095Mb (mask 0xffffffff)
<4>hde: safely enabled flush
<6>hde: 80418240 sectors (41174 MB) w/1916KiB Cache, CHS=79780/16/63
<4>blk: queue c031f514, I/O limit 4095Mb (mask 0xffffffff)
<4>hdf: set_drive_speed_status: status=0xff { Busy }
<4>hdf: set_drive_speed_status: status=0xff { Busy }
<4>hdf: drive not ready for command
<4>hdf: failed write cache flush, disabling ordered write support
<4>hdf: status timeout: status=0xff { Busy }
<4>hdf: drive not ready for command
<6>hdf: 117266688 sectors (60041 MB) w/1820KiB Cache, CHS=116336/16/63
<4>hdf: status timeout: status=0xff { Busy }
<4>hdf: drive not ready for command
<4>hdc: no flushcache support
<4>hdc: ATAPI 48X CD-ROM drive, 128kB Cache
<6>Uniform CD-ROM driver Revision: 3.12
<4>ide-floppy driver 0.99
<6>Partition check:
<6> hda: hda1 hda2 hda3
<6> hdd: [PTBL] [2434/255/63] hdd1 < hdd5 >
<6> hde:hde: status timeout: status=0xff { Busy }
<4>PDC202XX: Primary channel reset.
<4>hde: drive not ready for command
<4>ide2: reset timed-out, status=0xff
<4>hde: status timeout: status=0xff { Busy }
<4>PDC202XX: Primary channel reset.
<4>hde: drive not ready for command
<4>ide2: reset timed-out, status=0xff
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4> unable to read partition table
<6> hdf:hdf: status timeout: status=0xff { Busy }
<4>PDC202XX: Primary channel reset.
<4>hdf: drive not ready for command
<4>ide2: reset timed-out, status=0xff
<4>hdf: status timeout: status=0xff { Busy }
<4>PDC202XX: Primary channel reset.
<4>hdf: drive not ready for command
<4>ide2: reset timed-out, status=0xff
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<4> unable to read partition table
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<6>loop: loaded (max 16 devices)
<6>Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
<6>Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
<4>ide-floppy driver 0.99
<6>SCSI subsystem driver Revision: 1.00
<3>request_module[scsi_hostadapter]: Root fs not mounted
<3>request_module[scsi_hostadapter]: Root fs not mounted
<6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<4>IP: routing cache hash table of 4096 buckets, 32Kbytes
<4>TCP: Hash tables configured (established 32768 bind 32768)
<6>Linux IP multicast router 0.06 plus PIM-SM
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<5>RAMDISK: Compressed image found at block 0
<4>Uncompressing.................................. .......done.
<4>Freeing initrd memory: 4044k freed
<4>VFS: Mounted root (minix filesystem).
<7>VFS: Disk change detected on device ide1(22,0)
<6>Non-volatile memory driver v1.1
<7>VFS: Disk change detected on device fd(2,0)
<4>end_request: I/O error, dev 02:00 (floppy), sector 0
<7>VFS: Disk change detected on device fd(2,0)
<4>end_request: I/O error, dev 02:00 (floppy), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<7>ISO 9660 Extensions: Microsoft Joliet Level 3
<7>ISO 9660 Extensions: RRIP_1991A
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<7>VFS: Disk change detected on device fd(2,0)
<4>end_request: I/O error, dev 02:00 (floppy), sector 0
<7>VFS: Disk change detected on device fd(2,0)
<4>end_request: I/O error, dev 02:00 (floppy), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<7>VFS: Disk change detected on device fd(2,0)
<4>end_request: I/O error, dev 02:00 (floppy), sector 0
<7>VFS: Disk change detected on device fd(2,0)
<4>end_request: I/O error, dev 02:00 (floppy), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<6>parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
<4>imm: Version 2.05 (for Linux 2.4.0)
<4>ppa: Version 2.07 (for Linux 2.4.x)
<4>WARNING - no ppa compatible devices found.
<4> As of 31/Aug/1998 Iomega started shipping parallel
<4> port ZIP drives with a different interface which is
<4> supported by the imm (ZIP Plus) driver. If the
<4> cable is marked with "AutoDetect", this is what has
<4> happened.
<7>VFS: Disk change detected on device fd(2,0)
<4>end_request: I/O error, dev 02:00 (floppy), sector 0
<7>VFS: Disk change detected on device fd(2,0)
<4>end_request: I/O error, dev 02:00 (floppy), sector 0
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>LVM version 1.0.3(19/02/2002) module loaded
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<4>JFS development version: $Name: v1_0_16 $
<6>SGI XFS with ACLs, DMAPI, realtime, quota, no debug enabled
<6>Journalled Block Device driver loaded
<6>raid5: measuring checksumming speed
<4> 8regs : 870.000 MB/sec
<4> 32regs : 638.000 MB/sec
<4> pIII_sse : 1008.400 MB/sec
<4> pII_mmx : 1141.600 MB/sec
<4> p5_mmx : 1173.600 MB/sec
<4>raid5: using function: pIII_sse (1008.400 MB/sec)
<6>md: raid0 personality registered as nr 2
<6>md: raid1 personality registered as nr 3
<6>md: raid5 personality registered as nr 4
<4>reiserfs: checking transaction log (device 03:03) ...
<4>Using r5 hash to sort names
<4>ReiserFS version 3.6.25
<4>reiserfs: checking transaction log (device 03:03) ...
<4>Using r5 hash to sort names
<4>ReiserFS version 3.6.25
<6>Adding Swap: 530136k swap-space (priority -1)
<4>FAT: bogus logical sector size 5632
<3>cramfs: wrong magic
<4>reiserfs: checking transaction log (device 03:03) ...
<4>Using r5 hash to sort names
<4>ReiserFS version 3.6.25
<4>VFS: Mounted root (reiserfs filesystem) readonly.
<4>change_root: old root has d_count=21
<5>Trying to unmount old root ... okay
<4>Freeing unused kernel memory: 120k freed
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<4>end_request: I/O error, dev 21:00 (hde), sector 0
<4>end_request: I/O error, dev 21:00 (hde), sector 2
<4>end_request: I/O error, dev 21:00 (hde), sector 4
<4>end_request: I/O error, dev 21:00 (hde), sector 6
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4>end_request: I/O error, dev 21:40 (hdf), sector 2
<4>end_request: I/O error, dev 21:40 (hdf), sector 4
<4>end_request: I/O error, dev 21:40 (hdf), sector 6
<6>Adding Swap: 530136k swap-space (priority 42)
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.
Boot logging started on /dev/tty1(/dev/console) at Wed Jul 17 23:50:41 2002
Master Resource Control: previous runlevel: N, switching to runlevel:
5
<notice>/etc/init.d/rc5.d/S01isdn start
<notice>'/etc/init.d/rc5.d/S01isdn start' exits with status 0
<notice>/etc/init.d/rc5.d/S01personal-firewall.initial start
Starting personal-firewall (initial) [not active]
unused
<notice>'/etc/init.d/rc5.d/S01personal-firewall.initial start' exits with status 6
<notice>/etc/init.d/rc5.d/S01random start
Initializing random number generator
done
<notice>'/etc/init.d/rc5.d/S01random start' exits with status 0
<notice>/etc/init.d/rc5.d/S05network start
Setting up network interfaces:
lo
done
eth0
done
<notice>'/etc/init.d/rc5.d/S05network start' exits with status 0
<notice>/etc/init.d/rc5.d/S06syslog start
Starting syslog services<notice>startproc: execve (/sbin/syslogd) [ /sbin/syslogd ], [ PWD=/ SuSE=,1207300040,F3FADF3C., HOSTNAME=Heidiswelt CONSOLE=/dev/console vga=0x0317 PREVLEVEL=N REDIRECT=/dev/tty1 initrd=initrd MACHTYPE=i386-suse-linux expert=0 LINES=34 SHLVL=2 COLUMNS=105 BOOT_IMAGE=linux SHELL=/bin/bash HOSTTYPE=i386 OSTYPE=linux HOME=/ TERM=linux PATH=/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 INIT_VERSION=sysvinit-2.82 _=/sbin/startproc DAEMON=/sbin/syslogd ]
<notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 ], [ PWD=/ SuSE=,1207300040,F3FADF3C., HOSTNAME=Heidiswelt CONSOLE=/dev/console vga=0x0317 PREVLEVEL=N REDIRECT=/dev/tty1 initrd=initrd MACHTYPE=i386-suse-linux expert=0 LINES=34 SHLVL=2 COLUMNS=105 BOOT_IMAGE=linux SHELL=/bin/bash HOSTTYPE=i386 OSTYPE=linux HOME=/ TERM=linux PATH=/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 INIT_VERSION=sysvinit-2.82 _=/sbin/startproc DAEMON=/sbin/klogd ]
done
Starting hotplugging services [<notice>'/etc/init.d/rc5.d/S06syslog start' exits with status 0
<notice>/etc/init.d/rc5.d/S07hotplug start
net pci usb ]
failed
<notice>'/etc/init.d/rc5.d/S07hotplug start' exits with status 1
<notice>/etc/init.d/rc5.d/S08hwscan start
Starting hardware scan on boot<notice>'/etc/init.d/rc5.d/S08hwscan start' exits with status 0
<notice>/etc/init.d/rc5.d/S08portmap start
Starting RPC portmap daemon<notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ PWD=/ SuSE=,1207300040,F3FADF3C., HOSTNAME=Heidiswelt CONSOLE=/dev/console vga=0x0317 PREVLEVEL=N REDIRECT=/dev/tty1 initrd=initrd MACHTYPE=i386-suse-linux expert=0 LINES=34 SHLVL=2 COLUMNS=105 BOOT_IMAGE=linux SHELL=/bin/bash HOSTTYPE=i386 OSTYPE=linux HOME=/ TERM=linux PATH=/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 INIT_VERSION=sysvinit-2.82 _=/sbin/startproc DAEMON=/sbin/portmap ]
done
<notice>'/etc/init.d/rc5.d/S08portmap start' exits with status 0
<notice>/etc/init.d/rc5.d/S08splash_early start
<notice>'/etc/init.d/rc5.d/S08splash_early start' exits with status 0
<notice>/etc/init.d/rc5.d/S08sshd start
Starting SSH daemon<notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd ], [ PWD=/ SuSE=,1207300040,F3FADF3C., HOSTNAME=Heidiswelt CONSOLE=/dev/console vga=0x0317 PREVLEVEL=N REDIRECT=/dev/tty1 initrd=initrd MACHTYPE=i386-suse-linux expert=0 LINES=34 SHLVL=2 COLUMNS=105 BOOT_IMAGE=linux SHELL=/bin/bash HOSTTYPE=i386 OSTYPE=linux HOME=/ TERM=linux PATH=/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 INIT_VERSION=sysvinit-2.82 _=/sbin/startproc DAEMON=/usr/sbin/sshd ]
done
<notice>'/etc/init.d/rc5.d/S08sshd start' exits with status 0
<notice>/etc/init.d/rc5.d/S09nfs start
<notice>'/etc/init.d/rc5.d/S09nfs start' exits with status 0
<notice>/etc/init.d/rc5.d/S10alsasound start
Starting sound driver: es1938/lib/modules/2.4.18-4GB/kernel/sound/pci/snd-es1938.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters
/lib/modules/2.4.18-4GB/kernel/sound/pci/snd-es1938.o: insmod /lib/modules/2.4.18-4GB/kernel/sound/pci/snd-es1938.o failed
/lib/modules/2.4.18-4GB/kernel/sound/pci/snd-es1938.o: insmod snd-es1938 failed
failed
Starting service at daemon<notice>'/etc/init.d/rc5.d/S10alsasound start' exits with status 0
<notice>/etc/init.d/rc5.d/S10atd start
<notice>startproc: execve (/usr/sbin/atd) [ /usr/sbin/atd ], [ PWD=/ SuSE=,1207300040,F3FADF3C., HOSTNAME=Heidiswelt CONSOLE=/dev/console vga=0x0317 PREVLEVEL=N REDIRECT=/dev/tty1 initrd=initrd MACHTYPE=i386-suse-linux expert=0 LINES=34 SHLVL=2 COLUMNS=105 BOOT_IMAGE=linux SHELL=/bin/bash HOSTTYPE=i386 OSTYPE=linux HOME=/ TERM=linux PATH=/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 INIT_VERSION=sysvinit-2.82 _=/sbin/startproc DAEMON=/usr/sbin/atd ]
<notice>'/etc/init.d/rc5.d/S10atd start' exits with status 0
<notice>/etc/init.d/rc5.d/S10fbset start
done
<notice>'/etc/init.d/rc5.d/S10fbset start' exits with status 0
<notice>/etc/init.d/rc5.d/S10sendmail start
Initializing SMTP port (sendmail)<notice>startproc: execve (/usr/sbin/sendmail) [ /usr/sbin/sendmail -O DaemonPortOptions=Addr=127.0.0.1 -L sendmail -Am -bd -q30m -om ], [ PWD=/ SuSE=,1207300040,F3FADF3C., HOSTNAME=Heidiswelt CONSOLE=/dev/console vga=0x0317 PREVLEVEL=N REDIRECT=/dev/tty1 initrd=initrd MACHTYPE=i386-suse-linux expert=0 LINES=34 SHLVL=2 COLUMNS=105 BOOT_IMAGE=linux SHELL=/bin/bash HOSTTYPE=i386 OSTYPE=linux HOME=/ TERM=linux PATH=/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 INIT_VERSION=sysvinit-2.82 _=/sbin/startproc DAEMON=/usr/sbin/sendmail ]
<notice>startproc: execve (/usr/sbin/sendmail) [ /usr/sbin/sendmail -L sendmail-client -Ac -q30m ], [ PWD=/ SuSE=,1207300040,F3FADF3C., HOSTNAME=Heidiswelt CONSOLE=/dev/console vga=0x0317 PREVLEVEL=N REDIRECT=/dev/tty1 initrd=initrd MACHTYPE=i386-suse-linux expert=0 LINES=34 SHLVL=2 COLUMNS=105 BOOT_IMAGE=linux SHELL=/bin/bash HOSTTYPE=i386 OSTYPE=linux HOME=/ TERM=linux PATH=/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 INIT_VERSION=sysvinit-2.82 _=/sbin/startproc DAEMON=/usr/sbin/sendmail ]
done
<notice>'/etc/init.d/rc5.d/S10sendmail start' exits with status 0
<notice>/etc/init.d/rc5.d/S11kbd start
Loading keymap qwertz/de-latin1-nodeadkeys.map.gz
doneLoading compose table winkeys shiftctrl latin1.add
done
Loading console font lat9w-16.psfu
doneLoading screenmap trivial
doneSetting up console ttys
done<notice>'/etc/init.d/rc5.d/S11kbd start' exits with status 0
<notice>/etc/init.d/rc5.d/S11smbfs start
<notice>'/etc/init.d/rc5.d/S11smbfs start' exits with status 0
<notice>/etc/init.d/rc5.d/S11splash start
<notice>'/etc/init.d/rc5.d/S11splash start' exits with status 0
<notice>/etc/init.d/rc5.d/S11xdm start
Starting service kdm<notice>startproc: execve (/opt/kde3/bin/kdm) [ /opt/kde3/bin/kdm ], [ PWD=/ SuSE=,1207300040,F3FADF3C., LC_MESSAGES= HOSTNAME=Heidiswelt CONSOLE=/dev/console RC_LANG=de_DE@euro vga=0x0317 PREVLEVEL=N REDIRECT=/dev/tty1 QTDIR=/usr/lib/qt3 KDEROOTHOME=/root/.kdm initrd=initrd LC_TIME= MACHTYPE=i386-suse-linux RC_LC_COLLATE=POSIX LC_ALL= expert=0 LINES=34 LANG=de_DE@euro LC_NUMERIC= SHLVL=2 COLUMNS=105 LC_CTYPE=de_DE@euro BOOT_IMAGE=linux SHELL=/bin/bash PRINTER=lp HOSTTYPE=i386 OSTYPE=linux WINDOWMANAGER=/usr/X11R6/bin/kde HOME=/ TERM=linux no_proxy=localhost PATH=/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 LC_MONETARY= INIT_VERSION=sysvinit-2.82 LC_COLLATE=POSIX _=/sbin/startproc DAEMON=/opt/kde3/bin/kdm ]
done
<notice>'/etc/init.d/rc5.d/S11xdm start' exits with status 0
<notice>/etc/init.d/rc5.d/S12cron start
Starting CRON daemon<notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ PWD=/ SuSE=,1207300040,F3FADF3C., HOSTNAME=Heidiswelt CONSOLE=/dev/console vga=0x0317 PREVLEVEL=N REDIRECT=/dev/tty1 initrd=initrd MACHTYPE=i386-suse-linux expert=0 LINES=34 SHLVL=2 COLUMNS=105 BOOT_IMAGE=linux SHELL=/bin/bash HOSTTYPE=i386 OSTYPE=linux HOME=/ TERM=linux PATH=/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 INIT_VERSION=sysvinit-2.82 _=/sbin/startproc DAEMON=/usr/sbin/cron ]
done
<notice>'/etc/init.d/rc5.d/S12cron start' exits with status 0
<notice>/etc/init.d/rc5.d/S12nscd start
Starting Name Service Cache Daemon<notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ PWD=/ SuSE=,1207300040,F3FADF3C., HOSTNAME=Heidiswelt CONSOLE=/dev/console vga=0x0317 PREVLEVEL=N REDIRECT=/dev/tty1 initrd=initrd MACHTYPE=i386-suse-linux expert=0 LINES=34 SHLVL=2 COLUMNS=105 BOOT_IMAGE=linux SHELL=/bin/bash HOSTTYPE=i386 OSTYPE=linux HOME=/ TERM=linux PATH=/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 INIT_VERSION=sysvinit-2.82 _=/sbin/startproc DAEMON=/usr/sbin/nscd ]
done
<notice>'/etc/init.d/rc5.d/S12nscd start' exits with status 0
<notice>/etc/init.d/rc5.d/S22personal-firewall.final start
Starting personal-firewall (final) [not active]
unused
Master Resource Control: runlevel 5 has been
reached
Failed services in runlevel 5: hotplug
Skipped services in runlevel 5: personal-firewall.initial personal-firewall.final
<notice>'/etc/init.d/rc5.d/S22personal-firewall.final start' exits with status 6
<notice>/etc/init.d/rc5.d/S22splash_late start
<notice>'/etc/init.d/rc5.d/S22splash_late start' exits with status 0
<notice>killproc: kill(1759,3)
Zitieren
Lesezeichen