USB 3.0 PCIe Karte

[Andi123]

31

Servus

hab eine Delock USB 3.0 PCIe Karte gekauft, die ab Kernel 2.6. funktionieren soll.

http://www.delock.com/produkte/G_89281/merkmale.html

Leider tut sich nix, wenn ich da was einsteck!

Mint 14 64

root@andreas-linux-dt:~# lspci
00:00.0 Host bridge: Intel Corporation 82P965/G965 Memory Controller Hub (rev 02)
00:01.0 PCI bridge: Intel Corporation 82P965/G965 PCI Express Root Port (rev 02)
00:1a.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02)
00:1a.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02)
00:1a.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02)
00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 (rev 02)
00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 02)
00:1d.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02)
00:1d.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801H (ICH8 Family) 4 port SATA Controller [IDE mode] (rev 02)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
00:1f.5 IDE interface: Intel Corporation 82801HR/HO/HH (ICH8R/DO/DH) 2 port SATA Controller [IDE mode] (rev 02)
01:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller
01:00.1 IDE interface: VIA Technologies, Inc. VT6415 PATA IDE Host Controller (rev a0)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
03:00.0 RAID bus controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01)
04:00.0 USB controller: VIA Technologies, Inc. Device 3432 (rev 02)
05:01.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev 46)
06:00.0 VGA compatible controller: NVIDIA Corporation GF114 [GeForce GTX 560 Ti] (rev a1)
06:00.1 Audio device: NVIDIA Corporation GF114 HDMI Audio Controller (rev a1)

root@andreas-linux-dt:~# lsusb
Bus 002 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 004 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse
Bus 004 Device 003: ID 045e:0730 Microsoft Corp. Digital Media Keyboard 3000
Bus 006 Device 002: ID 046d:08da Logitech, Inc. QuickCam Messanger
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 004: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
root@andreas-linux-dt:~#

andreas@andreas-linux-dt:~$ dmesg | grep -i xhci
[    0.713189] xhci_hcd 0000:04:00.0: xHCI Host Controller
[    0.713193] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 8
[    0.713460] xhci_hcd 0000:04:00.0: irq 16, io mem 0xfbeff000
[    0.713515] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[    0.713566] usb usb8: Product: xHCI Host Controller
[    0.713567] usb usb8: Manufacturer: Linux 3.5.0-19-generic xhci_hcd
[    0.713624] xHCI xhci_add_endpoint called for root hub
[    0.713626] xHCI xhci_check_bandwidth called for root hub
[    0.713689] xhci_hcd 0000:04:00.0: xHCI Host Controller
[    0.713693] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 9
[    0.713725] usb usb9: Product: xHCI Host Controller
[    0.713727] usb usb9: Manufacturer: Linux 3.5.0-19-generic xhci_hcd
[    0.713789] xHCI xhci_add_endpoint called for root hub
[    0.713791] xHCI xhci_check_bandwidth called for root hub
[    3.000011] usb 8-1: new high-speed USB device number 2 using xhci_hcd
[    3.264537] usb 9-4: new SuperSpeed USB device number 2 using xhci_hcd
[   39.060535] usb 9-4: new SuperSpeed USB device number 3 using xhci_hcd
[   77.944008] xhci_hcd 0000:04:00.0: Timeout while waiting for address device command
[   77.948001] xhci_hcd 0000:04:00.0: Stopped the command ring failed, maybe the host is dead
[   77.948001] xhci_hcd 0000:04:00.0: Abort command ring failed
[   88.222107] xhci_hcd 0000:04:00.0: HC died; cleaning up
andreas@andreas-linux-dt:~$

Mit Win7 64 funktioniert die Karte einwandfrei!

Gruß

Andi

[Andi123]

dmesg

[    0.184940] pci 0000:00:1c.1: enabling device (0106 -> 0107)
[    0.184957] pci 0000:00:1e.0: setting latency timer to 64
[    0.184960] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.184962] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.184964] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.184965] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[    0.184967] pci_bus 0000:00: resource 8 [mem 0xe0000000-0xffffffff]
[    0.184969] pci_bus 0000:06: resource 0 [io  0xe000-0xefff]
[    0.184970] pci_bus 0000:06: resource 1 [mem 0xfc000000-0xfebfffff]
[    0.184972] pci_bus 0000:06: resource 2 [mem 0xe4000000-0xefffffff 64bit pref]
[    0.184974] pci_bus 0000:04: resource 0 [io  0xc000-0xcfff]
[    0.184975] pci_bus 0000:04: resource 1 [mem 0xfbe00000-0xfbefffff]
[    0.184977] pci_bus 0000:04: resource 2 [mem 0xe0000000-0xe01fffff 64bit pref]
[    0.184979] pci_bus 0000:03: resource 0 [io  0x1000-0x1fff]
[    0.184981] pci_bus 0000:03: resource 1 [mem 0xfbd00000-0xfbdfffff]
[    0.184982] pci_bus 0000:03: resource 2 [mem 0xe0200000-0xe03fffff 64bit pref]
[    0.184984] pci_bus 0000:02: resource 0 [io  0xb000-0xbfff]
[    0.184986] pci_bus 0000:02: resource 1 [mem 0xe0400000-0xe07fffff]
[    0.184987] pci_bus 0000:02: resource 2 [mem 0xe3f00000-0xe3ffffff 64bit pref]
[    0.184989] pci_bus 0000:01: resource 0 [io  0xa000-0xafff]
[    0.184990] pci_bus 0000:01: resource 1 [mem 0xfbc00000-0xfbcfffff]
[    0.184992] pci_bus 0000:01: resource 2 [mem 0xe0800000-0xe09fffff 64bit pref]
[    0.184994] pci_bus 0000:05: resource 0 [io  0xd000-0xdfff]
[    0.184996] pci_bus 0000:05: resource 1 [mem 0xfbf00000-0xfbffffff]
[    0.184997] pci_bus 0000:05: resource 4 [io  0x0000-0x0cf7]
[    0.184999] pci_bus 0000:05: resource 5 [io  0x0d00-0xffff]
[    0.185000] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff]
[    0.185002] pci_bus 0000:05: resource 7 [mem 0x000d0000-0x000dffff]
[    0.185003] pci_bus 0000:05: resource 8 [mem 0xe0000000-0xffffffff]
[    0.185039] NET: Registered protocol family 2
[    0.185228] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.186852] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.189604] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.190028] TCP: Hash tables configured (established 524288 bind 65536)
[    0.190030] TCP: reno registered
[    0.190042] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    0.190101] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    0.190246] NET: Registered protocol family 1
[    0.190456] pci 0000:06:00.0: Boot video device
[    0.190507] PCI: CLS 32 bytes, default 64
[    0.190509] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.190511] software IO TLB [mem 0xdbf96000-0xdff95fff] (64MB) mapped at [ffff8800dbf96000-ffff8800dff95fff]
[    0.190988] audit: initializing netlink socket (disabled)
[    0.190996] type=2000 audit(1355742773.184:1): initialized
[    0.209561] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.211587] VFS: Disk quotas dquot_6.5.2
[    0.211624] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.212060] fuse init (API version 7.19)
[    0.212139] msgmni has been set to 15921
[    0.212613] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.212643] io scheduler noop registered
[    0.212645] io scheduler deadline registered (default)
[    0.212668] io scheduler cfq registered
[    0.212790] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    0.212868] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[    0.212965] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
[    0.213060] pcieport 0000:00:1c.2: irq 43 for MSI/MSI-X
[    0.213155] pcieport 0000:00:1c.3: irq 44 for MSI/MSI-X
[    0.213241] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt
[    0.213243] pci 0000:06:00.0: Signaling PME through PCIe PME interrupt
[    0.213245] pci 0000:06:00.1: Signaling PME through PCIe PME interrupt
[    0.213248] pcie_pme 0000:00:01.0:pcie01: service driver pcie_pme loaded
[    0.213261] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[    0.213262] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt
[    0.213265] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[    0.213280] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt
[    0.213282] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[    0.213285] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded
[    0.213298] pcieport 0000:00:1c.2: Signaling PME through PCIe PME interrupt
[    0.213299] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[    0.213302] pcie_pme 0000:00:1c.2:pcie01: service driver pcie_pme loaded
[    0.213315] pcieport 0000:00:1c.3: Signaling PME through PCIe PME interrupt
[    0.213317] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[    0.213319] pci 0000:01:00.1: Signaling PME through PCIe PME interrupt
[    0.213322] pcie_pme 0000:00:1c.3:pcie01: service driver pcie_pme loaded
[    0.213337] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.213378] pciehp 0000:00:1c.0:pcie04: HPC vendor_id 8086 device_id 283f ss_vid 1849 ss_did 283f
[    0.213392] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded
[    0.213400] pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 device_id 2841 ss_vid 1849 ss_did 2841
[    0.213412] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded
[    0.213420] pciehp 0000:00:1c.2:pcie04: HPC vendor_id 8086 device_id 2843 ss_vid 1849 ss_did 2843
[    0.213433] pciehp 0000:00:1c.2:pcie04: service driver pciehp loaded
[    0.213441] pciehp 0000:00:1c.3:pcie04: HPC vendor_id 8086 device_id 2845 ss_vid 1849 ss_did 2845
[    0.213458] pciehp 0000:00:1c.3:pcie04: service driver pciehp loaded
[    0.213463] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.213505] intel_idle: does not run on family 6 model 23
[    0.213573] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[    0.213577] ACPI: Power Button [PWRB]
[    0.213612] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.213614] ACPI: Power Button [PWRF]
[    0.213686] ACPI: Requesting acpi_cpufreq
[    0.471777] Freeing initrd memory: 22464k freed
[    0.481116] GHES: HEST is not enabled!
[    0.481205] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.501521] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.522977] 00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.523147] Linux agpgart interface v0.103
[    0.524610] brd: module loaded
[    0.525280] loop: module loaded
[    0.525385] ata_piix 0000:00:1f.2: version 2.13
[    0.525398] ata_piix 0000:00:1f.2: MAP [
[    0.525399]  P0 P2 P1 P3 ]
[    0.680031] ata_piix 0000:00:1f.2: setting latency timer to 64
[    0.680258] scsi0 : ata_piix
[    0.680328] scsi1 : ata_piix
[    0.680969] ata1: SATA max UDMA/133 cmd 0x8080 ctl 0x8000 bmdma 0x7800 irq 19
[    0.680973] ata2: SATA max UDMA/133 cmd 0x7c00 ctl 0x7880 bmdma 0x7808 irq 19
[    0.680994] ata_piix 0000:00:1f.5: MAP [
[    0.680996]  P0 -- P1 -- ]
[    0.681041] ata_piix 0000:00:1f.5: setting latency timer to 64
[    0.681209] scsi2 : ata_piix
[    0.681271] scsi3 : ata_piix
[    0.681878] ata3: SATA max UDMA/133 cmd 0x9080 ctl 0x9000 bmdma 0x8800 irq 19
[    0.681881] ata4: SATA max UDMA/133 cmd 0x8c00 ctl 0x8880 bmdma 0x8808 irq 19
[    0.682152] Fixed MDIO Bus: probed
[    0.682187] tun: Universal TUN/TAP device driver, 1.6
[    0.682188] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.682232] PPP generic driver version 2.4.2
[    0.682280] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.682316] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    0.682319] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    0.682325] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    0.682349] ehci_hcd 0000:00:1a.7: debug port 1
[    0.686227] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[    0.686238] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfbbffc00
[    0.696018] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    0.696044] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.696046] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.696048] usb usb1: Product: EHCI Host Controller
[    0.696050] usb usb1: Manufacturer: Linux 3.5.0-19-generic ehci_hcd
[    0.696051] usb usb1: SerialNumber: 0000:00:1a.7
[    0.696137] hub 1-0:1.0: USB hub found
[    0.696140] hub 1-0:1.0: 4 ports detected
[    0.696201] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    0.696204] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    0.696207] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    0.696231] ehci_hcd 0000:00:1d.7: debug port 1
[    0.700113] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    0.700123] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfbbff800
[    0.712019] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.712043] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    0.712045] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.712047] usb usb2: Product: EHCI Host Controller
[    0.712048] usb usb2: Manufacturer: Linux 3.5.0-19-generic ehci_hcd
[    0.712050] usb usb2: SerialNumber: 0000:00:1d.7
[    0.712128] hub 2-0:1.0: USB hub found
[    0.712131] hub 2-0:1.0: 6 ports detected
[    0.712188] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.712201] uhci_hcd: USB Universal Host Controller Interface driver
[    0.712215] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    0.712218] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    0.712223] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    0.712251] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00009880
[    0.712277] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    0.712279] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.712281] usb usb3: Product: UHCI Host Controller
[    0.712282] usb usb3: Manufacturer: Linux 3.5.0-19-generic uhci_hcd
[    0.712284] usb usb3: SerialNumber: 0000:00:1a.0
[    0.712360] hub 3-0:1.0: USB hub found
[    0.712363] hub 3-0:1.0: 2 ports detected
[    0.712417] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    0.712420] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    0.712424] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    0.712450] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00009c00
[    0.712476] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    0.712478] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.712479] usb usb4: Product: UHCI Host Controller
[    0.712481] usb usb4: Manufacturer: Linux 3.5.0-19-generic uhci_hcd
[    0.712482] usb usb4: SerialNumber: 0000:00:1a.1
[    0.712560] hub 4-0:1.0: USB hub found
[    0.712563] hub 4-0:1.0: 2 ports detected
[    0.712612] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.712615] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.712619] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[    0.712637] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00009400
[    0.712668] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    0.712669] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.712671] usb usb5: Product: UHCI Host Controller
[    0.712673] usb usb5: Manufacturer: Linux 3.5.0-19-generic uhci_hcd
[    0.712674] usb usb5: SerialNumber: 0000:00:1d.0
[    0.712747] hub 5-0:1.0: USB hub found
[    0.712750] hub 5-0:1.0: 2 ports detected
[    0.712799] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    0.712802] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.712806] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[    0.712824] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00009480
[    0.712851] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    0.712853] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.712855] usb usb6: Product: UHCI Host Controller
[    0.712856] usb usb6: Manufacturer: Linux 3.5.0-19-generic uhci_hcd
[    0.712858] usb usb6: SerialNumber: 0000:00:1d.1
[    0.712932] hub 6-0:1.0: USB hub found
[    0.712935] hub 6-0:1.0: 2 ports detected
[    0.712987] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    0.712990] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.712994] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[    0.713012] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00009800
[    0.713040] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    0.713042] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.713043] usb usb7: Product: UHCI Host Controller
[    0.713045] usb usb7: Manufacturer: Linux 3.5.0-19-generic uhci_hcd
[    0.713046] usb usb7: SerialNumber: 0000:00:1d.2
[    0.713118] hub 7-0:1.0: USB hub found
[    0.713121] hub 7-0:1.0: 2 ports detected
[    0.713196] xhci_hcd 0000:03:00.0: xHCI Host Controller
[    0.713200] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 8
[    0.713476] xhci_hcd 0000:03:00.0: irq 17, io mem 0xfbdff000
[    0.713534] xhci_hcd 0000:03:00.0: irq 45 for MSI/MSI-X
[    0.713581] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[    0.713583] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.713585] usb usb8: Product: xHCI Host Controller
[    0.713586] usb usb8: Manufacturer: Linux 3.5.0-19-generic xhci_hcd
[    0.713588] usb usb8: SerialNumber: 0000:03:00.0
[    0.713644] xHCI xhci_add_endpoint called for root hub
[    0.713645] xHCI xhci_check_bandwidth called for root hub
[    0.713664] hub 8-0:1.0: USB hub found
[    0.713668] hub 8-0:1.0: 1 port detected
[    0.713710] xhci_hcd 0000:03:00.0: xHCI Host Controller
[    0.713713] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 9
[    0.713741] usb usb9: New USB device found, idVendor=1d6b, idProduct=0003
[    0.713743] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.713745] usb usb9: Product: xHCI Host Controller
[    0.713746] usb usb9: Manufacturer: Linux 3.5.0-19-generic xhci_hcd
[    0.713748] usb usb9: SerialNumber: 0000:03:00.0
[    0.713803] xHCI xhci_add_endpoint called for root hub
[    0.713805] xHCI xhci_check_bandwidth called for root hub
[    0.713821] hub 9-0:1.0: USB hub found
[    0.713828] hub 9-0:1.0: 4 ports detected
[    0.713947] usbcore: registered new interface driver libusual
[    0.713980] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    0.716446] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.716450] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.716559] mousedev: PS/2 mouse device common for all mice
[    0.716683] rtc_cmos 00:03: RTC can wake from S4
[    0.716785] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.716804] rtc0: alarms up to one month, y3k, 114 bytes nvram
[    0.716866] device-mapper: uevent: version 1.0.3
[    0.716924] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    0.716931] cpuidle: using governor ladder
[    0.716932] cpuidle: using governor menu
[    0.716933] EFI Variables Facility v0.08 2004-May-17
[    0.717102] ashmem: initialized
[    0.717212] TCP: cubic registered
[    0.717297] NET: Registered protocol family 10
[    0.717465] NET: Registered protocol family 17
[    0.717473] Key type dns_resolver registered
[    0.717608] PM: Hibernation image not present or could not be loaded.
[    0.717619] registered taskstats version 1
[    0.719981] Key type trusted registered
[    0.721653] Key type encrypted registered
[    0.723518]   Magic number: 8:647:226
[    0.723635] rtc_cmos 00:03: setting system clock to 2012-12-17 11:12:54 UTC (1355742774)
[    0.724198] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.724200] EDD information not available.
[    1.010608] ata4: SATA link down (SStatus 0 SControl 300)
[    1.156046] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.164122] ata3.00: ATAPI: HL-DT-STDVD-RAM GH22LS30, 1.01, max UDMA/100
[    1.180119] ata3.00: configured for UDMA/100
[    1.188018] Refined TSC clocksource calibration: 2659.601 MHz.
[    1.188022] Switching to clocksource tsc
[    1.330542] ata1.00: SATA link down (SStatus 0 SControl 300)
[    1.330553] ata1.01: SATA link down (SStatus 4 SControl 300)
[    1.376009] usb 2-1: new high-speed USB device number 2 using ehci_hcd
[    1.484050] ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.484059] ata2.01: SATA link down (SStatus 4 SControl 300)
[    1.509187] usb 2-1: New USB device found, idVendor=05e3, idProduct=0608
[    1.509189] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.509191] usb 2-1: Product: USB2.0 Hub
[    1.509458] hub 2-1:1.0: USB hub found
[    1.509686] hub 2-1:1.0: 4 ports detected
[    1.541780] ata2.00: ATA-7: ST3250820AS, 3.AAD, max UDMA/133
[    1.541782] ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    1.608412] ata2.00: configured for UDMA/133
[    1.608511] scsi 1:0:0:0: Direct-Access     ATA      ST3250820AS      3.AA PQ: 0 ANSI: 5
[    1.608620] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    1.608628] sd 1:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[    1.608684] sd 1:0:0:0: [sda] Write Protect is off
[    1.608687] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.608708] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.660545]  sda: sda1 sda2 < sda5 >
[    1.660762] sd 1:0:0:0: [sda] Attached SCSI disk
[    1.661920] scsi 2:0:0:0: CD-ROM            HL-DT-ST DVD-RAM GH22LS30 1.01 PQ: 0 ANSI: 5
[    1.663966] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.663968] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.664037] sr 2:0:0:0: Attached scsi CD-ROM sr0
[    1.664088] sr 2:0:0:0: Attached scsi generic sg1 type 5
[    1.665183] Freeing unused kernel memory: 928k freed
[    1.665364] Write protecting the kernel read-only data: 12288k
[    1.668945] Freeing unused kernel memory: 1464k freed
[    1.671836] Freeing unused kernel memory: 1120k freed
[    1.686123] udevd[109]: starting version 175
[    1.717677] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.717774] r8169 0000:02:00.0: irq 46 for MSI/MSI-X
[    1.717949] r8169 0000:02:00.0: eth0: RTL8168d/8111d at 0xffffc90000c74000, bc:5f:f4:47:8f:bb, XID 081000c0 IRQ 46
[    1.717952] r8169 0000:02:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    1.725443] sata_sil24 0000:04:00.0: version 1.1
[    1.726942] scsi4 : sata_sil24
[    1.727927] scsi5 : sata_sil24
[    1.727984] ata5: SATA max UDMA/100 host m128@0xfbeffc00 port 0xfbef8000 irq 16
[    1.727987] ata6: SATA max UDMA/100 host m128@0xfbeffc00 port 0xfbefa000 irq 16
[    1.780051] firewire_ohci 0000:01:00.0: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x11
[    1.780134] pata_via 0000:01:00.1: version 0.3.4
[    1.780454] scsi6 : pata_via
[    1.780515] scsi7 : pata_via
[    1.780642] ata7: PATA max UDMA/133 cmd 0xac00 ctl 0xa880 bmdma 0xa400 irq 19
[    1.780644] ata8: PATA max UDMA/133 cmd 0xa800 ctl 0xa480 bmdma 0xa408 irq 19
[    1.844048] firewire_ohci 0000:05:01.0: added OHCI v1.0 device as card 1, 8 IR + 8 IT contexts, quirks 0x11
[    1.860019] usb 4-1: new low-speed USB device number 2 using uhci_hcd
[    2.033523] usb 4-1: New USB device found, idVendor=046d, idProduct=c00c
[    2.033526] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.033528] usb 4-1: Product: USB Mouse
[    2.033530] usb 4-1: Manufacturer: Logitech
[    2.276007] usb 4-2: new low-speed USB device number 3 using uhci_hcd
[    2.280063] firewire_core 0000:01:00.0: created device fw0: GUID 008f1300aba61200, S400
[    2.344050] firewire_core 0000:05:01.0: created device fw1: GUID 0005ce0088101bbf, S400
[    2.459535] usb 4-2: New USB device found, idVendor=045e, idProduct=0730
[    2.459537] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.459538] usb 4-2: Product: Microsoft\xffffffc2\xffffffae\xffffffae Digital Media Keyboard 3000
[    2.459540] usb 4-2: Manufacturer: Microsoft
[    2.494074] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Digital Media Keyboard 3000 as /devices/pci0000:00/0000:00:1a.1/usb4/4-2/4-2:1.0/input/input2
[    2.494158] microsoft 0003:045E:0730.0002: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Digital Media Keyboard 3000] on usb-0000:00:1a.1-2/input0
[    2.523667] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Digital Media Keyboard 3000 as /devices/pci0000:00/0000:00:1a.1/usb4/4-2/4-2:1.1/input/input3
[    2.523740] microsoft 0003:045E:0730.0003: input,hidraw1: USB HID v1.11 Device [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Digital Media Keyboard 3000] on usb-0000:00:1a.1-2/input1
[    2.523756] usbcore: registered new interface driver usbhid
[    2.523758] usbhid: USB HID core driver
[    2.700008] usb 6-2: new full-speed USB device number 2 using uhci_hcd
[    2.887931] usb 6-2: New USB device found, idVendor=046d, idProduct=08da
[    2.887933] usb 6-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    3.000011] usb 8-1: new high-speed USB device number 2 using xhci_hcd
[    3.016815] usb 8-1: New USB device found, idVendor=2109, idProduct=0811
[    3.016818] usb 8-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    3.016819] usb 8-1: Product: USB2.0 Hub
[    3.017258] hub 8-1:1.0: USB hub found
[    3.017402] hub 8-1:1.0: 4 ports detected
[    3.264555] usb 9-4: new SuperSpeed USB device number 2 using xhci_hcd
[    3.281078] usb 9-4: Parent hub missing LPM exit latency info.  Power management will be impacted.
[    3.282657] usb 9-4: New USB device found, idVendor=05dc, idProduct=b049
[    3.282659] usb 9-4: New USB device strings: Mfr=3, Product=4, SerialNumber=5
[    3.282661] usb 9-4: Product: USB_3_0 Reader 
[    3.282662] usb 9-4: Manufacturer: Lexar 
[    3.282664] usb 9-4: SerialNumber: 000000006358
[    3.284467] Initializing USB Mass Storage driver...
[    3.284589] scsi8 : usb-storage 9-4:1.0
[    3.284649] usbcore: registered new interface driver usb-storage
[    3.284651] USB Mass Storage support registered.
[    3.284653] usbcore: registered new interface driver uas
[    3.480255] usb 2-1.4: new high-speed USB device number 4 using ehci_hcd
[    3.573255] usb 2-1.4: New USB device found, idVendor=05e3, idProduct=0608
[    3.573257] usb 2-1.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    3.573259] usb 2-1.4: Product: USB2.0 Hub
[    3.573534] hub 2-1.4:1.0: USB hub found
[    3.573881] hub 2-1.4:1.0: 4 ports detected
[    3.808021] ata5: SATA link down (SStatus 0 SControl 0)
[    4.284712] scsi 8:0:0:0: Direct-Access     Lexar    CF  USB_3_0 Read LX01 PQ: 0 ANSI: 5
[    4.285182] scsi 8:0:0:1: Direct-Access     Lexar    SD  USB_3_0 Read LX01 PQ: 0 ANSI: 5
[    4.285625] sd 8:0:0:0: Attached scsi generic sg2 type 0
[    4.285750] sd 8:0:0:1: Attached scsi generic sg3 type 0
[    4.492487] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[    4.492676] sd 8:0:0:1: [sdc] 7959552 512-byte logical blocks: (4.07 GB/3.79 GiB)
[    4.493398] sd 8:0:0:1: [sdc] Write Protect is off
[    4.493400] sd 8:0:0:1: [sdc] Mode Sense: 21 00 00 00
[    4.494160] sd 8:0:0:1: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    4.497972]  sdc: sdc1
[    4.499851] sd 8:0:0:1: [sdc] Attached SCSI removable disk
[    5.888020] ata6: SATA link down (SStatus 0 SControl 0)
[    6.049062] input: Logitech USB Mouse as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.0/input/input4
[    6.049200] hid-generic 0003:046D:C00C.0001: input,hidraw2: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:1a.1-1/input0
[   12.576019] usb 9-4: USB disconnect, device number 2
[   38.816240] sd 8:0:0:0: Device offlined - not ready after error recovery
[   39.060552] usb 9-4: new SuperSpeed USB device number 3 using xhci_hcd
[   39.077072] usb 9-4: Parent hub missing LPM exit latency info.  Power management will be impacted.
[   39.078585] usb 9-4: New USB device found, idVendor=05dc, idProduct=b049
[   39.078587] usb 9-4: New USB device strings: Mfr=3, Product=4, SerialNumber=5
[   39.078589] usb 9-4: Product: USB_3_0 Reader 
[   39.078591] usb 9-4: Manufacturer: Lexar 
[   39.078592] usb 9-4: SerialNumber: 000000006358
[   39.079325] scsi9 : usb-storage 9-4:1.0
[   39.522269] EXT4-fs (dm-1): INFO: recovery required on readonly filesystem
[   39.522272] EXT4-fs (dm-1): write access will be enabled during recovery
[   40.076799] scsi 9:0:0:0: Direct-Access     Lexar    CF  USB_3_0 Read LX01 PQ: 0 ANSI: 5
[   40.077273] scsi 9:0:0:1: Direct-Access     Lexar    SD  USB_3_0 Read LX01 PQ: 0 ANSI: 5
[   40.077771] sd 9:0:0:0: Attached scsi generic sg2 type 0
[   40.078128] sd 9:0:0:1: Attached scsi generic sg3 type 0
[   40.285358] sd 9:0:0:0: [sdb] Attached SCSI removable disk
[   40.285542] sd 9:0:0:1: [sdc] 7959552 512-byte logical blocks: (4.07 GB/3.79 GiB)
[   40.287067] sd 9:0:0:1: [sdc] Write Protect is off
[   40.287069] sd 9:0:0:1: [sdc] Mode Sense: 21 00 00 00
[   40.288626] sd 9:0:0:1: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   40.293926]  sdc: sdc1
[   40.296668] sd 9:0:0:1: [sdc] Attached SCSI removable disk
[   43.215851] EXT4-fs (dm-1): recovery complete
[   43.259670] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[   46.872028] usb 9-4: USB disconnect, device number 3
[   59.596685] Adding 8388604k swap on /dev/mapper/ubuntu-swap_1.  Priority:-1 extents:1 across:8388604k 
[   59.601809] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   59.631508] udevd[572]: starting version 175
[   59.681066] lp: driver loaded but no devices found
[   59.693280] nvidia: module license 'NVIDIA' taints kernel.
[   59.693285] Disabling lock debugging due to kernel taint
[   59.717810] vgaarb: device changed decodes: PCI:0000:06:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   59.718505] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  313.09  Tue Dec  4 21:22:17 PST 2012
[   59.749633] parport_pc 00:06: reported by Plug and Play ACPI
[   59.749688] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[   59.760280] ACPI Warning: 0x0000000000000860-0x000000000000087f SystemIO conflicts with Region \_SB_.PCI0.GFX0.TCOI 1 (20120320/utaddress-251)
[   59.760287] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   59.760289] lpc_ich: Resource conflict(s) found affecting iTCO_wdt
[   59.760292] ACPI Warning: 0x0000000000000828-0x000000000000082f SystemIO conflicts with Region \PMRG 1 (20120320/utaddress-251)
[   59.760295] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   59.760297] ACPI Warning: 0x0000000000000480-0x00000000000004bf SystemIO conflicts with Region \GPR2 1 (20120320/utaddress-251)
[   59.760300] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   59.760301] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   59.779392] type=1400 audit(1355739233.549:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=755 comm="apparmor_parser"
[   59.779716] type=1400 audit(1355739233.549:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=755 comm="apparmor_parser"
[   59.779900] type=1400 audit(1355739233.549:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=755 comm="apparmor_parser"
[   59.788465] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X
[   59.809641] Linux video capture interface: v2.00
[   59.809990] gspca_main: v2.14.0 registered
[   59.810245] gspca_main: gspca_zc3xx-2.14.0 probing 046d:08da
[   59.814395] microcode: CPU0 sig=0x1067a, pf=0x10, revision=0xa07
[   59.832100] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[   59.832169] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[   59.832228] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[   59.832326] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[   59.832391] input: HDA Intel Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   59.832469] input: HDA Intel Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   59.832540] input: HDA Intel Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   59.832634] input: HDA Intel Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[   59.832908] hda_intel: Disabling MSI
[   59.832918] hda-intel: 0000:06:00.1: Handle VGA-switcheroo audio client
[   59.844125] lp0: using parport0 (interrupt-driven).
[   59.890985] ppdev: user-space parallel port driver
[   60.146294] EXT4-fs (dm-1): re-mounted. Opts: errors=remount-ro
[   60.314828] microcode: CPU1 sig=0x1067a, pf=0x10, revision=0xa07
[   60.316116] microcode: CPU2 sig=0x1067a, pf=0x10, revision=0xa07
[   60.317304] microcode: CPU3 sig=0x1067a, pf=0x10, revision=0xa07
[   60.318409] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[   60.720106] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:06:00.1/sound/card1/input13
[   60.720186] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:06:00.1/sound/card1/input14
[   60.720249] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:06:00.1/sound/card1/input15
[   60.720312] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:06:00.1/sound/card1/input16
[   60.901899] input: gspca_zc3xx as /devices/pci0000:00/0000:00:1d.1/usb6/6-2/input/input17
[   60.902134] usbcore: registered new interface driver gspca_zc3xx
[   60.905062] usbcore: registered new interface driver snd-usb-audio
[   61.018008] init: failsafe main process (1121) killed by TERM signal
[   61.131247] type=1400 audit(1355739234.901:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1195 comm="apparmor_parser"
[   61.131572] type=1400 audit(1355739234.901:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/x86_64-linux-gnu/lightdm-remote-session-uccsconfigure/uccsconfigure-session-wrapper" pid=1194 comm="apparmor_parser"
[   61.131580] type=1400 audit(1355739234.901:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1195 comm="apparmor_parser"
[   61.131767] type=1400 audit(1355739234.901:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1195 comm="apparmor_parser"
[   61.131844] type=1400 audit(1355739234.901:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/x86_64-linux-gnu/lightdm-remote-session-uccsconfigure/uccsconfigure-session-wrapper//chromium_browser" pid=1194 comm="apparmor_parser"
[   61.132047] type=1400 audit(1355739234.905:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1192 comm="apparmor_parser"
[   61.132321] type=1400 audit(1355739234.905:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper//chromium_browser" pid=1192 comm="apparmor_parser"
[   61.161113] Bluetooth: Core ver 2.16
[   61.161146] NET: Registered protocol family 31
[   61.161148] Bluetooth: HCI device and connection manager initialized
[   61.161288] Bluetooth: HCI socket layer initialized
[   61.161290] Bluetooth: L2CAP socket layer initialized
[   61.161294] Bluetooth: SCO socket layer initialized
[   61.165235] Bluetooth: RFCOMM TTY layer initialized
[   61.165240] Bluetooth: RFCOMM socket layer initialized
[   61.165242] Bluetooth: RFCOMM ver 1.11
[   61.176051] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   61.176054] Bluetooth: BNEP filters: protocol multicast
[   61.303719] r8169 0000:02:00.0: eth0: link down
[   61.303729] r8169 0000:02:00.0: eth0: link down
[   61.304546] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   61.304804] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   63.281265] r8169 0000:02:00.0: eth0: link up
[   63.282024] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   72.832253] sd 9:0:0:0: Device offlined - not ready after error recovery
[   72.836536] sdc: detected capacity change from 4075290624 to 0
[   73.031838] vboxdrv: Found 4 processor cores.
[   73.032021] vboxdrv: fAsync=0 offMin=0x208 offMax=0xa770
[   73.032172] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   73.032173] vboxdrv: Successfully loaded version 4.2.4 (interface 0x001a0004).
[   73.072628] init: udev-fallback-graphics main process (1989) terminated with status 1
[   73.076598] usb 9-4: new SuperSpeed USB device number 4 using xhci_hcd
[   73.082377] init: lightdm main process (2005) killed by TERM signal
[   73.093084] usb 9-4: Parent hub missing LPM exit latency info.  Power management will be impacted.
[   73.094670] usb 9-4: New USB device found, idVendor=05dc, idProduct=b049
[   73.094672] usb 9-4: New USB device strings: Mfr=3, Product=4, SerialNumber=5
[   73.094674] usb 9-4: Product: USB_3_0 Reader 
[   73.094675] usb 9-4: Manufacturer: Lexar 
[   73.094677] usb 9-4: SerialNumber: 000000006358
[   73.095410] scsi10 : usb-storage 9-4:1.0
[   73.239058] vboxpci: IOMMU not found (not registered)
[   74.093672] scsi 10:0:0:0: Direct-Access     Lexar    CF  USB_3_0 Read LX01 PQ: 0 ANSI: 5
[   74.094159] scsi 10:0:0:1: Direct-Access     Lexar    SD  USB_3_0 Read LX01 PQ: 0 ANSI: 5
[   74.095955] sd 10:0:0:0: Attached scsi generic sg2 type 0
[   74.096161] sd 10:0:0:1: Attached scsi generic sg3 type 0
[   74.302473] sd 10:0:0:0: [sdb] Attached SCSI removable disk
[   74.302657] sd 10:0:0:1: [sdc] 7959552 512-byte logical blocks: (4.07 GB/3.79 GiB)
[   74.304171] sd 10:0:0:1: [sdc] Write Protect is off
[   74.304174] sd 10:0:0:1: [sdc] Mode Sense: 21 00 00 00
[   74.305764] sd 10:0:0:1: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   74.311162]  sdc: sdc1
[   74.313130] sd 10:0:0:1: [sdc] Attached SCSI removable disk
[   76.995015] init: plymouth-stop pre-start process (2323) terminated with status 1
[  111.960019] xhci_hcd 0000:03:00.0: Timeout while waiting for address device command
[  112.615918] xhci_hcd 0000:03:00.0: Stopped the command ring failed, maybe the host is dead
[  112.615918] xhci_hcd 0000:03:00.0: Abort command ring failed
[  122.234030] Clocksource tsc unstable (delta = 9373940553 ns)
[  122.234238] xhci_hcd 0000:03:00.0: HC died; cleaning up
[  122.234309] usb 8-1: USB disconnect, device number 2
[  122.234436] Switching to clocksource acpi_pm
[  122.234528] usb 9-4: USB disconnect, device number 0
[  122.236006] [sched_delayed] sched: RT throttling activated
[  122.640029] usb 9-4: device not accepting address 4, error -22
[  122.640038] hub 9-0:1.0: cannot reset port 4 (err = -19)
[  122.640108] sd 10:0:0:0: Device offlined - not ready after error recovery
root@andreas-linux-dt:~#

Der an die Karte angeschlossene Lexar Kartenleser mit den beiden eingesteckten Karten (1x SD 1xCF) sind gelistet!

[   74.093672] scsi 10:0:0:0: Direct-Access     Lexar    CF  USB_3_0 Read LX01 PQ: 0 ANSI: 5
[   74.094159] scsi 10:0:0:1: Direct-Access     Lexar    SD  USB_3_0 Read LX01 PQ: 0 ANSI: 5
[   74.095955] sd 10:0:0:0: Attached scsi generic sg2 type 0
[   74.096161] sd 10:0:0:1: Attached scsi generic sg3 type 0

[Andi123]

Hab Kernel 3.7. installiert, jetzt funzt der USB 3.0 PCIe Kontroller, aber die eSATA PCIe Karte ebenfalls von Delock geht nicht mehr,
Die hat mit den 3.5er Kernel noch funktioniert.

Schon beim Systemstart gibt es Fehlermeldungen

SATA5 Failure
SATA6 Failure

Ist eine 2 Port-Karte von Delock!

Ich kann doch nicht wenn ich den Kartenleser brauche mit 3.7. starten, wen ich die externe eSATA Platte brauche, mit 3.5.

[Andi123]

Nach erneuten Systemstart geht es schon wieder nimmer!

Ich geb's auf mit Linux.

Seit Jahren versuch ich immer wieder ein lauffahiges Linux hinzubekommen.

Leider ohne Erfolg!


Na denn, wieder Windows!

[davidbaumann]

Eventuell auch weil du die ganzen Komponenten zusammenwürfelst?

Was hast du noch an Erweiterungen drin? noch eine PCI Grafikkarte?

Edit: Wenn ich mir Hardware kaufe, schaue nicht auf die Seite des Herstellers, der die Platine in den Karton einpackt, sondern welcher Controller verbaut ist.
Realtek z.B. sind da gut, Intel auch...

Gruß.

[Andi123]

Wenn ich mir Hardware kaufe, schaue nicht auf die Seite des Herstellers, der die Platine in den Karton einpackt, sondern welcher Controller verbaut ist.

Hab keine Linuxtaugliche USB 3.0 Karte ausser den Delocks gefunden!

Und eine neue Platine mit Prozessor, Speicher kann ich mir nicht leisten!

[-hanky-]

Ich hab hier eine Karte von Logilink verbaut [1], die läuft problemlos. Ist vielleicht einen Versuch wert, die Karte bekommt man für knapp einen Zehner. Ansonsten halte ich es wie davidbaumann und schaue nach dem verbauten Chipsatz. Auf Herstellerangaben verlasse ich mich nicht, damit habe ich schon schlechte Erfahrungen gemacht.

Was den eSATA-Controller angeht: Was heißt "geht nicht"? Was steht dazu in den Logfiles? Wenn ich das richtig sehe ist das ein "SiI 3132"-Chipsatz, der sollte eigentlich von Kernel 3.7 unterstützt werden.

-hanky-

[1] http://www.logilink.eu/showproduct/PC0054.htm

[Andi123]

@-hanky-

leider kommt der Tip zu spät, hab eine Karte mit NEC D0720201 Chip bestellt.

NEC Chips sollen wohl 'Linuxtauglich' sein!

http://www.ebay.de/itm/ws/eBayISAPI....E:L:OC:DE:3160

Mal schauen ...

Nach einer Beschwerdemail an Delock bekam ich folgende Antwort

vielen Dank für Ihre Nachricht.
 
 
Leider ist die Produktbeschreibung schon etwas älter und müsste überarbeitet werden.
Zum damaligen Zeitpunkt waren Linux-Systeme mit einem Kernel 3.x nicht verfügbar.
 
Im Moment liegen keine Testergebnisse für unsere Karte im Bezug auf eine Kompatibilität mit einem Linux-System vor, welches einen Kernel 3.5 oder einen Kernel 3.7 verwendet.
Die Kompatibilität wird erst in den kommenden Wochen getestet, bis zu diesem Zeitpunkt können wir eine Kompatibilität unserer Karte mit diesem Betriebssystemen nicht beurteilen.
 
Wir können auf kurze Sicht keine Lösung anbieten.

Aber anbieten tun sie es 'ab Kernel 2.6'

[-hanky-]

Hi,

NEC sollte passen. Meine Karte von Logilink hat einen ähnlichen Chip:

02:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)

-hanky-

[davidbaumann]

Denke mal hier kann man sich für andere Distributionen auch in etwa orientieren.

Gruß.

[Andi123]

Der NEC D0720201 Chip zeigt schon beim Start eine "xhci failed" Meldung!

Ich werd es wohl aufgeben müssen mit Linux, ist ein ewiger Kampf.

Scheint wohl nur VM tauglich zu sein, schade

Gruß

Andi

[Andi123]

Mit Kernel 3.7.5 geht jetzt die Delock USB 3.0 Karte

Ein paar Neustarts waren aber schon nötig

Gruß

Andi

[Andi123]

Aber leider wird die Speicherkarte nur erkannt wenn sie vor dem Systemstart in den Kartenleser gesteckt wird.

Ohne gibt es beim Start einen xhci error Fehler!