Code:
Inspecting /boot/System.map-2.6.18.8-0.1-default
Loaded 23380 symbols from /boot/System.map-2.6.18.8-0.1-default.
Symbols match kernel version 2.6.18.
No module symbols loaded - kernel modules not enabled.
klogd 1.4.1, log source = ksyslog started.
<5>Linux version 2.6.18.8-0.1-default (geeko@buildhost) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #1 SMP Fri Mar 2 13:51:59 UTC 2007
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
<4> BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000001be90000 (usable)
<4> BIOS-e820: 000000001be90000 - 000000001be9a000 (ACPI data)
<4> BIOS-e820: 000000001be9a000 - 000000001bf00000 (ACPI NVS)
<4> BIOS-e820: 000000001bf00000 - 0000000020000000 (reserved)
<4> BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
<4> BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
<4> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
<4> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
<5>0MB HIGHMEM available.
<5>446MB LOWMEM available.
<6>found SMP MP-table at 000f8110
<7>On node 0 totalpages: 114320
<7> DMA zone: 4096 pages, LIFO batch:0
<7> Normal zone: 110224 pages, LIFO batch:31
<6>DMI present.
<6>Using APIC driver default
<6>IO/L-APIC allowed because system is MP or new enough
<7>ACPI: RSDP (v000 ACRSYS ) @ 0x000f8040
<7>ACPI: RSDT (v001 ACRSYS RSDT 0x06040000 LTP 0x00000000) @ 0x1be91ba9
<7>ACPI: FADT (v001 ATI Bowfin 0x06040000 ATI 0x000f4240) @ 0x1be99ca0
<7>ACPI: SLIC (v001 ACRSYS ACRPRDCT 0x06040000 LOHR 0x00000000) @ 0x1be99d14
<7>ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1be99e8a
<7>ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x1be99f7e
<7>ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x1be99fc4
<7>ACPI: DSDT (v001 Acer Navarro 0x06040000 MSFT 0x03000000) @ 0x00000000
<6>ATI board detected. Disabling timer routing over 8254.
<6>ACPI: PM-Timer IO Port: 0x8008
<7>ACPI: Local APIC address 0xfee00000
<6>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
<4>Processor #0 15:12 APIC version 16
<6>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
<6>ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
<4>IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
<7>ACPI: IRQ9 used by override.
<4>Enabling APIC mode: Flat. Using 1 I/O APICs
<6>Using ACPI (MADT) for SMP configuration information
<4>Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
<4>Detected 1795.641 MHz processor.
<4>Built 1 zonelists. Total pages: 114320
<5>Kernel command line: root=/dev/hda6 vga=0x314 resume=/dev/hda7 splash=silent elevator=
<6>bootsplash: silent mode.
<7>mapped APIC to ffffd000 (fee00000)
<7>mapped IOAPIC to ffffc000 (fec00000)
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Initializing CPU#0
<4>PID hash table entries: 2048 (order: 11, 8192 bytes)
<4>Console: colour dummy device 80x25
<4>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
<4>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>Memory: 446240k/457280k available (1697k kernel code, 10468k reserved, 972k data, 196k init, 0k highmem)
<4>Checking if this processor honours the WP bit even in supervisor mode... Ok.
<4>Calibrating delay using timer specific routine.. 3594.75 BogoMIPS (lpj=7189501)
<6>Security Framework v1.0.0 initialized
<4>Mount-cache hash table entries: 512
<7>CPU: After generic identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 00000019
<7>CPU: After vendor identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 00000019
<6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
<6>CPU: L2 Cache: 256K (64 bytes/line)
<7>CPU: After all inits, caps: 078bfbff ebd3fbff 00000000 00000410 00002001 00000000 00000019
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<4>Compat vDSO mapped to ffffe000.
<6>Checking 'hlt' instruction... OK.
<6>SMP alternatives: switching to UP code
<6>Freeing SMP alternatives: 16k freed
<6>checking if image is initramfs... it is
<6>Freeing initrd memory: 3155k freed
<6>ACPI: Core revision 20060707
<4>CPU0: AMD Mobile AMD Sempron(tm) Processor 3400+ stepping 02
<6>Total of 1 processors activated (3594.75 BogoMIPS).
<4>ENABLING IO-APIC IRQs
<6>..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
<6>Brought up 1 CPUs
<4>migration_cost=0
<6>NET: Registered protocol family 16
<6>ACPI: bus type pci registered
<6>PCI: Using MMCONFIG
<5>PCI: No mmconfig possible on 0:18
<4>Setting up standard PCI resources
<6>ACPI: Interpreter enabled
<6>ACPI: Using IOAPIC for interrupt routing
<6>ACPI: PCI Root Bridge [PCI0] (0000:00)
<7>PCI: Probing PCI hardware (bus 00)
<6>PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
<7>Boot video device is 0000:01:05.0
<6>PCI: Transparent bridge - 0000:00:14.4
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BB4_._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BB5_._PRT]
<4>ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled.
<6>ACPI: Embedded Controller [EC0] (gpe 16) interrupt mode.
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
<6>Linux Plug and Play Support v0.97 (c) Adam Belay
<6>pnp: PnP ACPI init
<6>pnp: PnP ACPI: found 10 devices
<6>PnPBIOS: Disabled by ACPI PNP
<6>PCI: Using ACPI for IRQ routing
<6>PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
<3>PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0
<3>PCI: Cannot allocate resource region 8 of bridge 0000:00:04.0
<3>PCI: Cannot allocate resource region 9 of bridge 0000:00:04.0
<3>PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0
<3>PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0
<6>pnp: 00:08: ioport range 0x1080-0x1080 has been reserved
<6>pnp: 00:08: ioport range 0x40b-0x40b has been reserved
<6>pnp: 00:08: ioport range 0x4d0-0x4d1 has been reserved
<6>pnp: 00:08: ioport range 0x4d6-0x4d6 has been reserved
<6>PCI: Bridge: 0000:00:01.0
<6> IO window: 9000-9fff
<6> MEM window: d0100000-d01fffff
<6> PREFETCH window: d4000000-d7ffffff
<6>PCI: Bridge: 0000:00:04.0
<6> IO window: disabled.
<6> MEM window: disabled.
<6> PREFETCH window: disabled.
<6>PCI: Bridge: 0000:00:05.0
<6> IO window: disabled.
<6> MEM window: disabled.
<6> PREFETCH window: disabled.
<4>PCI: Bus 7, cardbus bridge: 0000:06:04.0
<4> IO window: 0000a400-0000a4ff
<4> IO window: 0000a800-0000a8ff
<4> PREFETCH window: 30000000-31ffffff
<4> MEM window: 32000000-33ffffff
<6>PCI: Bridge: 0000:00:14.4
<6> IO window: a000-afff
<6> MEM window: d0200000-d02fffff
<6> PREFETCH window: 30000000-31ffffff
<7>PCI: Setting latency timer of device 0000:00:04.0 to 64
<7>PCI: Setting latency timer of device 0000:00:05.0 to 64
<6>ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 20 (level, low) -> IRQ 177
<6>NET: Registered protocol family 2
<4>IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
<4>TCP established hash table entries: 16384 (order: 5, 131072 bytes)
<4>TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
<6>TCP: Hash tables configured (established 16384 bind 8192)
<6>TCP reno registered
<6>Machine check exception polling timer started.
<6>apm: BIOS not found.
<6>audit: initializing netlink socket (disabled)
<5>audit(1176744603.764:1): initialized
<4>Total HugeTLB memory allocated, 0
<5>VFS: Disk quotas dquot_6.5.1
<4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>Initializing Cryptographic API
<6>io scheduler noop registered
<6>io scheduler anticipatory registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<7>PCI: Setting latency timer of device 0000:00:04.0 to 64
<4>pcie_portdrv_probe->Dev[5a36:1002] has invalid IRQ. Check vendor BIOS
<4>assign_interrupt_mode Found MSI capability
<7>Allocate Port Service[0000:00:04.0:pcie00]
<7>Allocate Port Service[0000:00:04.0:pcie01]
<7>Allocate Port Service[0000:00:04.0:pcie03]
<7>PCI: Setting latency timer of device 0000:00:05.0 to 64
<4>pcie_portdrv_probe->Dev[5a37:1002] has invalid IRQ. Check vendor BIOS
<4>assign_interrupt_mode Found MSI capability
<7>Allocate Port Service[0000:00:05.0:pcie00]
<7>Allocate Port Service[0000:00:05.0:pcie01]
<7>Allocate Port Service[0000:00:05.0:pcie03]
<6>vesafb: framebuffer at 0xd4000000, mapped to 0xdc880000, using 3750k, total 16384k
<6>vesafb: mode is 800x600x16, linelength=1600, pages=16
<6>vesafb: protected mode interface info at c000:53f8
<6>vesafb: pmi: set display start = c00c5466, set palette = c00c54a0
<6>vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4
<6>vesafb: scrolling: redraw
<6>vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
<6>bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 82985 bytes,<6>...found (800x600, 49016 bytes, v3).
<4>Console: switching to colour frame buffer device 96x33
<6>fb0: VESA VGA frame buffer device
<6>isapnp: Scanning for PnP cards...
<6>isapnp: No Plug & Play device found
<6>Real Time Clock Driver v1.12ac
<6>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
<4>floppy0: no floppy controllers found
<4>RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
<6>PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSS0] at 0x60,0x64 irq 1,12
<6>i8042.c: Detected active multiplexing controller, rev 1.1.
<6>serio: i8042 AUX0 port at 0x60,0x64 irq 12
<6>serio: i8042 AUX1 port at 0x60,0x64 irq 12
<6>serio: i8042 AUX2 port at 0x60,0x64 irq 12
<6>serio: i8042 AUX3 port at 0x60,0x64 irq 12
<6>serio: i8042 KBD port at 0x60,0x64 irq 1
<6>mice: PS/2 mouse device common for all mice
<6>input: PC Speaker as /class/input/input0
<6>md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: bitmap version 4.39
<6>NET: Registered protocol family 1
<4>Using IPI No-Shortcut mode
<6>ACPI: (supports S0 S3 S4 S5)
<6>Time: tsc clocksource has been installed.
<6>Freeing unused kernel memory: 196k freed
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
<4>ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
<3>ACPI: Getting cpuindex for acpiid 0x1
<6>Time: acpi_pm clocksource has been installed.
<4>ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707]
<6>ACPI: Thermal Zone [THRM] (42 C)
<6>ATIIXP: IDE controller at PCI slot 0000:00:14.1
<6>ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 209
<6>ATIIXP: chipset revision 128
<6>ATIIXP: not 100% native mode: will probe irqs later
<6> ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hda:DMA, hdb:DMA
<6>ATIIXP: simplex device: DMA disabled
<6>ide1: ATIIXP Bus-Master DMA disabled (BIOS)
<7>Probing IDE interface ide0...
<6>input: AT Translated Set 2 keyboard as /class/input/input1
<4>hda: TOSHIBA MK1234GAX, ATA DISK drive
<4>hdb: PHILIPS DVD-RAM SDVD8821, ATAPI CD/DVD-ROM drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<6>Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1280b1, caps: 0xa04713/0x204000
<6>hda: max request size: 512KiB
<6>hda: 234441648 sectors (120034 MB), CHS=16383/255/63, UDMA(100)
<6>hda: cache flushes supported
<6> hda: hda1 hda2 <<6>input: SynPS/2 Synaptics TouchPad as /class/input/input2
<4> hda5<4>psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
<4> hda6 hda7 hda8 >
<7>Probing IDE interface ide1...
<6>BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
<4>Attempting manual resume
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on hda6, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1280b1, caps: 0xa04713/0x204000
<6>input: SynPS/2 Synaptics TouchPad as /class/input/input3
<4>snd_page_alloc: disagrees about version of symbol struct_module
<4>soundcore: disagrees about version of symbol struct_module
<4>snd: disagrees about version of symbol struct_module
<4>i2c_core: disagrees about version of symbol struct_module
<4>snd_timer: disagrees about version of symbol struct_module
<4>snd_pcm: disagrees about version of symbol struct_module
<4>snd_hda_codec: disagrees about version of symbol struct_module
<4>snd_hda_intel: disagrees about version of symbol struct_module
<4>usbcore: disagrees about version of symbol struct_module
<4>usbcore: disagrees about version of symbol struct_module
<4>usbcore: disagrees about version of symbol struct_module
<4>ath_hal: module license 'Proprietary' taints kernel.
<6>ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
<4>mii: disagrees about version of symbol struct_module
<4>ehci_hcd: disagrees about version of symbol struct_module
<4>agpgart: disagrees about version of symbol struct_module
<4>i2c_piix4: disagrees about version of symbol struct_module
<6>wlan: 0.8.4.2 (0.9.3)
<4>cdrom: disagrees about version of symbol struct_module
<4>ohci_hcd: disagrees about version of symbol struct_module
<4>ohci_hcd: disagrees about version of symbol struct_module
<4>8139too: disagrees about version of symbol struct_module
<4>ati_agp: disagrees about version of symbol struct_module
<6>ath_pci: 0.9.4.5 (0.9.3)
<6>ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 22 (level, low) -> IRQ 217
<4>ide_cd: disagrees about version of symbol struct_module
<6>ath_rate_sample: 1.2 (0.9.3)
<4>wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
<4>wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
<4>wifi0: H/W encryption support: WEP AES AES_CCM TKIP
<4>wifi0: mac 7.8 phy 4.5 radio 5.6
<4>wifi0: Use hw queue 1 for WME_AC_BE traffic
<4>wifi0: Use hw queue 0 for WME_AC_BK traffic
<4>wifi0: Use hw queue 2 for WME_AC_VI traffic
<4>wifi0: Use hw queue 3 for WME_AC_VO traffic
<4>wifi0: Use hw queue 8 for CAB traffic
<4>wifi0: Use hw queue 9 for beacons
<6>wifi0: Atheros 5212: mem=0xd0200000, irq=217
<6>Adding 1534168k swap on /dev/hda7. Priority:-1 extents:1 across:1534168k
<4>loop: disagrees about version of symbol struct_module
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on hda8, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<4>ntfs: disagrees about version of symbol struct_module
<4>fat: disagrees about version of symbol struct_module
<4>vfat: disagrees about version of symbol struct_module
<4>aamatch_pcre: disagrees about version of symbol struct_module
<4>apparmor: disagrees about version of symbol struct_module
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.
Boot logging started on /dev/tty1(/dev/console) at Mon Apr 16 17:30:07 2007
Trying manual resume from /dev/hda7
Creating device nodes with udev
Loading ide-core
Loading ide-disk
Loading processor
Loading thermal
Loading atiixp
Loading fan
Loading edd
Loading jbd
Loading mbcache
Loading ext3
Invoking userspace resume from /dev/hda7
resume: Could not stat configuration file
resume: libgcrypt version: 1.2.3
resume: Could not read the image
Invoking in-kernel resume from /dev/hda7
Waiting for device /dev/hda6 to appear: ok
fsck 1.39 (29-May-2006)
[/bin/fsck.ext3 (1) -- /] fsck.ext3 -a -C0 /dev/hda6
/dev/hda6: clean, 440057/1330368 files, 2493976/2658749 blocks
fsck succeeded. Mounting root device read-write.
Mounting root /dev/hda6
Boot logging started on /dev/tty1(/dev/console (deleted)) at Mon Apr 16 19:30:12 2007
<notice>boot.udev start
Starting udevd done
<notice>'boot.udev start' exits with status 0
<notice>boot.rootfsck start
Activating swap-devices in /etc/fstab...
done<notice>'boot.rootfsck start' exits with status 0
<notice>boot.loadmodules start
Loading required kernel modules
done<notice>'boot.loadmodules start' exits with status 0
<notice>boot.preload_early start
done
<notice>'boot.preload_early start' exits with status 0
<notice>boot.device-mapper start
Activating device mapper...
FATAL: Module dm_mod not found.
failed
<notice>'boot.device-mapper start' exits with status 0
<notice>boot.md start
Starting MD Raid done
<notice>'boot.md start' exits with status 0
<notice>boot.lvm start
Waiting for udev to settle...
Scanning for LVM volume groups...
Reading all physical volumes. This may take a while...
No volume groups found
No volume groups found
/proc/misc: No entry for device-mapper found
Is device-mapper driver missing from kernel?
Failure to communicate with kernel device-mapper driver.
Activating LVM volume groups...
No volume groups found
done
<notice>'boot.lvm start' exits with status 0
<notice>boot.localfs start
Checking file systems...
fsck 1.39 (29-May-2006)
/dev/hda8: clean, 94983/1778880 files, 2275431/3554373 blocks
donedone
Mounting local file systems...
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
debugfs on /sys/kernel/debug type debugfs (rw)
udev on /dev type tmpfs (rw)
FATAL: Error inserting loop (/lib/modules/2.6.18.8-0.1-default/kernel/drivers/block/loop.ko): Invalid module format
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/hda8 on /home type ext3 (rw,acl,user_xattr)
modprobe: FATAL: Error inserting ntfs (/lib/modules/2.6.18.8-0.1-default/kernel/fs/ntfs/ntfs.ko): Invalid module format
mount: unknown filesystem type 'ntfs'
modprobe: WARNING: Error inserting fat (/lib/modules/2.6.18.8-0.1-default/kernel/fs/fat/fat.ko): Invalid module format
modprobe: FATAL: Error inserting vfat (/lib/modules/2.6.18.8-0.1-default/kernel/fs/vfat/vfat.ko): Invalid module format
mount: unknown filesystem type 'vfat'
failed<notice>'boot.localfs start' exits with status 0
<notice>boot.apparmor start
WARNING: Error inserting aamatch_pcre (/lib/modules/2.6.18.8-0.1-default/kernel/security/apparmor/match/aamatch_pcre.ko): Invalid module format
FATAL: Error inserting apparmor (/lib/modules/2.6.18.8-0.1-default/kernel/security/apparmor/apparmor.ko): Invalid module format
Loading AppArmor module failed
- could not start AppArmorfailed
<notice>'boot.apparmor start' exits with status 255
<notice>boot.cleanup start
<notice>'boot.cleanup start' exits with status 0
<notice>boot.clock start
Setting up the hardware clockdone
<notice>'boot.clock start' exits with status 0
<notice>boot.klog start
Creating /var/log/boot.msg
done<notice>killproc: kill(894,29)
<notice>'boot.klog start' exits with status 0
<notice>boot.proc start
<notice>'boot.proc start' exits with status 0
<notice>boot.scpm start
<notice>'boot.scpm start' exits with status 0
<notice>boot.sysctl start
Setting current sysctl status from /etc/sysctl.conf
net.ipv4.icmp_echo_ignore_broadcasts = 1
net.ipv4.conf.all.rp_filter = 1
done
<notice>'boot.sysctl start' exits with status 0
<notice>boot.udev_retry start
Retry device configurationdone
<notice>'boot.udev_retry start' exits with status 0
<notice>boot.videobios start
<notice>'boot.videobios start' exits with status 0
<notice>boot.crypto start
<notice>'boot.crypto start' exits with status 0
<notice>boot.ipconfig start
Enabling syn flood protectiondone
Enabling IP forwardingdone
done
<notice>'boot.ipconfig start' exits with status 0
<notice>boot.localnet start
Setting up hostname 'linux-lhm8'done
Setting up loopback interface lo
lo IP address: 127.0.0.1/8
done
<notice>'boot.localnet start' exits with status 0
<notice>boot.preload start
done
<notice>'boot.preload start' exits with status 0
<notice>boot.swap start
Activating remaining swap-devices in /etc/fstab...
done<notice>'boot.swap start' exits with status 0
<notice>SuSEfirewall2_init start
Starting Firewall Initialization (phase 1 of 2) SuSEfirewall2: Warning: ip6tables does not support state matching. Extended IPv6 support disabled.
SuSEfirewall2: Warning: Kernel lacks support for IPv6 REJECT target! Using DROP for IPv6 instead.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
WARNING: Error inserting nfnetlink (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/nfnetlink.ko): Invalid module format
FATAL: Error inserting ip_conntrack (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_conntrack.ko): Invalid module format
FATAL: Module ip6table_filter not found.
FATAL: Module ip6table_mangle not found.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables-batch v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
SuSEfirewall2: Error: iptables-batch failed, re-running using iptables
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `nat': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `nat': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `mangle': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `mangle': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
WARNING: Error inserting x_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/netfilter/x_tables.ko): Invalid module format
FATAL: Error inserting ip_tables (/lib/modules/2.6.18.8-0.1-default/kernel/net/ipv4/netfilter/ip_tables.ko): Invalid module format
iptables v1.3.6: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
done
<notice>'SuSEfirewall2_init start' exits with status 0
<notice>boot.ldconfig start
<notice>'boot.ldconfig start' exits with status 0
System Boot Control: The system has been set up
System Boot Control: Running /etc/init.d/boot.local
done<notice>killproc: kill(894,3)
INIT:
Boot logging started on /dev/tty1(/dev/console) at Mon Apr 16 17:30:36 2007
Master Resource Control: previous runlevel: N, switching to runlevel: 5
Entering runlevel: 5
modprobe: FATAL: Error inserting ac (/lib/modules/2.6.18.8-0.1-default/kernel/drivers/acpi/ac.ko): Invalid module format
WARNING: Error inserting aamatch_pcre
SuSE 10.2 : Kernel Disaster!
Zitieren
Lesezeichen