Probleme bei WLAN mit WPA

[oSonnYo]

Also:

• Den Router kann ich (erstmal) leider nicht umkonfigurieren
• Acerhk ist schon installiert, Hotekey funktioniert (leuchtet) auch

• ifconfig eth0 <ip> up
  iwconfig eth0 essid <essid>
  route add default gw <ip-router>
  ping google.de

  mit passenden Änderungen ausgeführt, keine Fehlermeldungen, aber der Ping schlägt Fehl
• rpm -qa|grep ipw gibt folgendes aus:
  

  ipw3945d-1.7.18-29
  ipw-firmware-7-31BOOTPROTO='dhcp'

• sudo cat /etc/sysconfig/network/ifcfg-wlan* gibt das hier aus:
  

  BROADCAST=''
  ETHTOOL_OPTIONS=''
  IFPLUGD_PRIORITY='10'
  IPADDR=''
  MTU=''
  NAME='Intel PRO/Wireless 2200BG Network Connection'
  NETMASK=''
  NETWORK=''
  REMOTE_IPADDR=''
  STARTMODE='ifplugd'
  UNIQUE='rBUF.9J1F3mK3OuC'
  USERCONTROL='yes'
  WIRELESS_AP=''
  WIRELESS_AUTH_MODE='psk'
  WIRELESS_BITRATE='auto'
  WIRELESS_CA_CERT=''
  WIRELESS_CHANNEL=''
  WIRELESS_CLIENT_CERT=''
  WIRELESS_CLIENT_KEY=''
  WIRELESS_CLIENT_KEY_PASSWORD=''
  WIRELESS_DEFAULT_KEY='0'
  WIRELESS_EAP_AUTH=''
  WIRELESS_EAP_MODE=''
  WIRELESS_ESSID='FRITZ!Box Fon WLAN 7170'
  WIRELESS_FREQUENCY=''
  WIRELESS_KEY=''
  WIRELESS_KEY_0=''
  WIRELESS_KEY_1=''
  WIRELESS_KEY_2=''
  WIRELESS_KEY_3=''
  WIRELESS_KEY_LENGTH='128'
  WIRELESS_MODE='Managed'
  WIRELESS_NICK=''
  WIRELESS_NWID=''
  WIRELESS_PEAP_VERSION=''
  WIRELESS_POWER='yes'
  WIRELESS_WPA_ANONID=''
  WIRELESS_WPA_IDENTITY=''
  WIRELESS_WPA_PASSWORD=''
  WIRELESS_WPA_PSK='***********'
  _nm_name='bus-pci-0000:06:04.0'

• dmesg |grep ipw gibt das hier aus:
  

  ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.1.2kmprq
  ipw2200: Copyright(c) 2003-2006 Intel Corporation
  ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
  ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
  ipw2200: Failed to send SCAN_ABORT: Command timed out.
  ipw2200: Failed to send CARD_DISABLE: Command timed out.
  ipw2200: Failed to send SCAN_ABORT: Command timed out.
  ipw2200: Failed to send CARD_DISABLE: Command timed out.

  Wobei

  ipw2200: Failed to send SCAN_ABORT: Command timed out.
  ipw2200: Failed to send CARD_DISABLE: Command timed out.

  immer auftaucht wenn ich 2mal auf den Hotkey drücke.
• sudo grep ipw /var/log/messages gibt das hier aus:
  

  Jan  6 14:51:29 linux kernel: ipw2200: Failed to send CARD_DISABLE: Command timed out.
  Jan  6 15:53:08 nb-stefan kernel: ipw2200: Failed to send SCAN_ABORT: Command timed out.
  Jan  6 15:53:08 nb-stefan kernel: ipw2200: Firmware error detected.  Restarting.
  Jan  6 16:03:07 nb-stefan kernel: ipw2200: Failed to send CARD_DISABLE: Command timed out.
  Jan  6 18:00:52 nb-stefan kernel: ipw2200: Firmware error detected.  Restarting.
  Jan  6 18:01:33 nb-stefan kernel: ipw2200: Firmware error detected.  Restarting.
  Jan  6 18:31:00 nb-stefan kernel: ipw2200: Failed to send CARD_DISABLE: Command timed out.
  Jan  6 19:24:58 nb-stefan kernel: ipw2200: Firmware error detected.  Restarting.
  Jan  6 19:24:59 nb-stefan kernel: ipw2200: Firmware error detected.  Restarting.
  Jan  7 17:39:23 nb-stefan kernel: ipw2200: Firmware error detected.  Restarting.
  Jan  7 17:52:28 nb-stefan kernel: ipw2200: Failed to send CARD_DISABLE: Command timed out.
  Jan  7 17:54:02 nb-stefan kernel: ipw2200: Failed to send SCAN_ABORT: Command timed out.
  Jan  7 17:54:03 nb-stefan kernel: ipw2200: Failed to send CARD_DISABLE: Command timed out.
  Jan  7 18:11:17 nb-stefan kernel: ipw2200: Failed to send SCAN_ABORT: Command timed out.
  Jan  7 18:11:18 nb-stefan kernel: ipw2200: Failed to send CARD_DISABLE: Command timed out.
  Jan  7 18:13:44 nb-stefan kernel: ipw2200: Firmware error detected.  Restarting.
  Jan  7 18:22:57 nb-stefan kernel: ipw2200: Firmware error detected.  Restarting.
  Jan  7 18:28:31 nb-stefan kernel: ipw2200: Firmware error detected.  Restarting.
  Jan  7 18:33:37 nb-stefan kernel: ipw2200: Firmware error detected.  Restarting.
  Jan  7 19:24:09 nb-stefan kernel: ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.1.2kmprq
  Jan  7 19:24:09 nb-stefan kernel: ipw2200: Copyright(c) 2003-2006 Intel Corporation
  Jan  7 19:24:09 nb-stefan kernel: ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
  Jan  7 19:24:09 nb-stefan kernel: ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
  Jan  7 22:33:43 nb-stefan kernel: ipw2200: Failed to send SCAN_ABORT: Command timed out.
  Jan  7 22:33:45 nb-stefan kernel: ipw2200: Failed to send CARD_DISABLE: Command timed out.
  Jan  8 13:16:11 nb-stefan kernel: ipw2200: Failed to send SCAN_ABORT: Command timed out.
  Jan  8 13:16:13 nb-stefan kernel: ipw2200: Failed to send CARD_DISABLE: Command timed out.
  Jan  8 13:23:07 nb-stefan kernel: ipw2200: Failed to send SCAN_ABORT: Command timed out.
  Jan  8 13:23:08 nb-stefan kernel: ipw2200: Failed to send CARD_DISABLE: Command timed out.
  Jan  8 13:24:25 nb-stefan kernel: ipw2200: Failed to send SCAN_ABORT: Command timed out.
  Jan  8 13:24:26 nb-stefan kernel: ipw2200: Failed to send CARD_DISABLE: Command timed out.
  Jan  8 13:24:59 nb-stefan kernel: ipw2200: Failed to send CARD_DISABLE: Command timed out.
  Jan  8 13:25:54 nb-stefan sudo:     root : TTY=pts/1 ; PWD=/home/stefan ; USER=root ; COMMAND=/usr/bin/grep ipw /var/log/messages

• wpa_supplicant -Dipw -ieth2 -cDocuments/wpa_supplicant.conf -dd gibt das aus und wiederholt es regelmäßig:
  

  No keys have been configured - skip key clearing
  wpa_driver_ipw_set_drop_unencrypted: enabled=1
  ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
  State: ASSOCIATING -> ASSOCIATING
  ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
  ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
  Setting authentication timeout: 10 sec 0 usec
  EAPOL: External notification - EAP success=0
  EAPOL: External notification - EAP fail=0
  EAPOL: External notification - portControl=Auto
  Wireless event: cmd=0x8b1a len=32
  Wireless event: cmd=0x8b19 len=8
  Received 272 bytes of scan results (1 BSSes)
  Scan results: 1
  Selecting BSS from priority group 0
  0: 00:15:0c:98:ad:f6 ssid='FRITZ!Box Fon WLAN 7170' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
     selected based on WPA IE
  Trying to associate with 00:15:0c:98:ad:f6 (SSID='FRITZ!Box Fon WLAN 7170' freq=0 MHz)
  Cancelling scan request
  WPA: clearing own WPA/RSN IE
  Automatic auth_alg selection: 0x1
  wpa_driver_ipw_set_auth_alg: auth_alg=0x1
  ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
  WPA: using IEEE 802.11i/D3.0
  WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
  WPA: set AP WPA IE - hexdump(len=26): dd 18 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 00 00
  WPA: clearing AP RSN IE
  WPA: using GTK TKIP
  WPA: using PTK TKIP
  WPA: using KEY_MGMT WPA-PSK
  WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
  No keys have been configured - skip key clearing
  wpa_driver_ipw_set_drop_unencrypted: enabled=1
  ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
  State: ASSOCIATING -> ASSOCIATING
  ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
  ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
  Setting authentication timeout: 10 sec 0 usec
  EAPOL: External notification - EAP success=0
  EAPOL: External notification - EAP fail=0
  EAPOL: External notification - portControl=Auto
  Wireless event: cmd=0x8b1a len=32
  CTRL-EVENT-TERMINATING - signal 2 received
  Removing interface eth2
  State: ASSOCIATING -> DISCONNECTED
  No keys have been configured - skip key clearing
  EAPOL: External notification - portEnabled=0
  EAPOL: External notification - portValid=0
  wpa_driver_ipw_set_wpa: enabled=0
  ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
  ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
  wpa_driver_ipw_set_drop_unencrypted: enabled=0
  ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
  wpa_driver_ipw_set_countermeasures: enabled=0
  ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
  No keys have been configured - skip key clearing
  Cancelling scan request

Danke erstmal für die ganze Hilfe. Ich denke hieraus kann man ein paar Fehler ablesen (ich kann sie bloß nicht erkennen). Ich habe während der Befehle auch ein paar mal die Hotkey Taste ausprobiert (was die Wiederholungen erklärt?). Vielleicht ist der acerhk Treiber falsch installiert? Ich weiß es nicht.

Danke für eure Hilfe

[oSonnYo]

Was ich grade noch bemerkt hab:
Als ich vorhin den Laptop anhatte war die Wireless Schnittstelle eth2, ich hab ihn nun grade nochmal angemacht, nun ist sie eth0

[Rain_maker]

Aha.

Dann gib uns mal ein:

cat /etc/udev/rules.d/*net_persistent*

und lies Dir noch das hier durch.

http://www.root-forum.org/kompiliere...ghlight=acerhk

BTW:

Karte mit Networkmanager eingerichtet oder Traditionell mit ifup?

ESSID versteckt?

Greetz,

RM

[oSonnYo]

Karte ist traditionell eingerichtet.

Der Befehl gibt folgende Ausgabe:

# This rules are autogenerated from /lib/udev/rename_netiface.
# But you can modify them, but make sure that you don't use an interface name
# twice. Also add such interface name rules only in this rules file. Otherwise
# rename_netiface will create wrong rules for new interfaces.
# It is safe to delete a rule, as long as you did not disable automatic rule
# generation. Only if all interfaces get a rule the renaming will work
# flawlessly. See also /etc/udev/rules.d/31-net_create_names.rules.
#
# Read /usr/share/doc/packages/sysconfig/README.Persistent_Interface_Names for
# further information.
#
# Use only a-z, A-Z and 0-9 for interface names!
#
SUBSYSTEM=="net", ACTION=="add", SYSFS{address}=="00:16:6f:b8:18:b2", IMPORT="/lib/udev/rename_netiface %k eth0"
SUBSYSTEM=="net", ACTION=="add", SYSFS{address}=="00:16:36:32:e6:f4", IMPORT="/lib/udev/rename_netiface %k eth1"
SUBSYSTEM=="net", ACTION=="add", SYSFS{address}=="00:16:6f:b8:18:b2", IMPORT="/lib/udev/rename_netiface %k eth2"

lese grad noch den anderen thread durch

[oSonnYo]

Ich habe jetzt die Tipps befolgt, aber keine Änderungen: es geht immernoch nicht.

wpa_supplicant -Dipw -i eth0 -c Documents/wpa_supplicant.conf -w gibt das aus:

Trying to associate with 00:15:0c:98:ad:f6 (SSID='FRITZ!Box Fon WLAN 7170' freq=0 MHz)
Trying to associate with 00:15:0c:98:ad:f6 (SSID='FRITZ!Box Fon WLAN 7170' freq=0 MHz)
Trying to associate with 00:15:0c:98:ad:f6 (SSID='FRITZ!Box Fon WLAN 7170' freq=0 MHz)
Trying to associate with 00:15:0c:98:ad:f6 (SSID='FRITZ!Box Fon WLAN 7170' freq=0 MHz)
Trying to associate with 00:15:0c:98:ad:f6 (SSID='FRITZ!Box Fon WLAN 7170' freq=0 MHz)
Trying to associate with 00:15:0c:98:ad:f6 (SSID='FRITZ!Box Fon WLAN 7170' freq=0 MHz)
Trying to associate with 00:15:0c:98:ad:f6 (SSID='FRITZ!Box Fon WLAN 7170' freq=0 MHz)
Trying to associate with 00:15:0c:98:ad:f6 (SSID='FRITZ!Box Fon WLAN 7170' freq=0 MHz)
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys

Bis ich dann irgenwann abbreche...

Und das wenn ich statt wext ipw als treiber nutze:

Trying to associate with 00:15:0c:98:ad:f6 (SSID='FRITZ!Box Fon WLAN 7170' freq=0 MHz)
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.

Wieder bis ich abbreche.
Weiß jemand was das "Failed to set encryption" bedeutet/wie man es löst?

[Rain_maker]

WAS hast Du gemacht?

So macht das keinen Sinn, beschreibe GENAU, was Du gemacht hast.

Welche Dateien hast Du verändert? Wie sehen diese JETZT aus?

Ich bin kein Wahrsager, also liefere Infos.

BTW:

wpa_supplicant -Dipw -i eth0 -c Documents/wpa_supplicant.conf -w

Du benutzt SuSE, also brauchst Du keine eigene wpa_supplicant.conf anlegen, das macht das System dynamisch aus dem Config-File von Yast.

Greetz,

RM

[oSonnYo]

Ich habe es geschafft: Ich hab nun eine Verbindung. SO hab ichs gemacht:

• In Yast die Konfiguration gelöscht.
• Den "doppelten" Eintrag in /etc/udev/rules.d/*net_persistent* gelöscht.
• Im Router WPA ausgeschaltet.
• In Yast die Schnittstelle neu eingerichtet mit DHCP und bei Verschlüsselung "Öffnen", Kennwort keines. Eingerichtet habe ich das über den Networkmanager
• Verbindung mit dem Frontend KNetworkmanager getestet => funktionierte
• Router umkonfiguriert => WPA aktiviert.
• Bei KNetworkmanager versucht wieder zuverbinden, dabei musste ich dann die Verschlüsselungsmethode und das Kennwort eingeben.

Und dann funktionierte es. Endlich kann ich mit WLAN surfen. Danke allen für ihr Hilfe und ihr Tipps!

Gruß und Dank,
Sonny