Hallo Gemeinde,
nach dem Booten werden mir zwar sda1 und sdb1 und sdb2 (und die gleich zweimal !!!) angezeigt, aber ich kann noch nicht darauf zugreifen. Erst wenn ich die beiden ab-- und wieder anstöpsele ist alles ok. Wie kann ich das so einrichten, dass die beim Booten schonn richtig erkannt und gemounted werden ?
vielen Dank im voraus
Gruß Stradti
Wie lautet die Ausgabe von "dmesg" nach dem Booten und nach dem Wiederanstöpseln?
Und welche Distribution verwendest Du überhaupt?
Gruß Oli.
Hallo Oli,
danke für Deine schnelle Antwort. Da ich neu hier im Forum bin, weiss ich nicht, wie ich die 1000 Zeilen, die demsg herausgibt, hier posten kann. Übrigens benutze ich Suse Linux 9.2
Gruß Stradti
Hallo Oli,
ich kann im Moment nur folgendes berichten:
beim Booten wird angezeigt
mount: /dev/sda1 is not a valid block device
mount: /dev/sdb1 is not a valid block device
mount: /dev/sdb2 is not a valid block device
Wie gesagt, es werden sda1, sdb1, und das ist das seltsame, sdb2 zweimal angezeigt. Alle als Windows-Laufwerke dargestellt, doch die zweite sdb2 als USB-Laufwerk, und auf die kann ich auch schon zugreifen.
Gruß Stradti
Hallo Oli,
ich habe mal einen filecompare zw. dmesg direkt nach dem Booten und nach dem neuen einstöpseln gemacht :
Vergleichen der Dateien dmesg_vor.txt und DMESG_NACH.TXT
***** dmesg_vor.txt
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1406.565 MHz processor.
Using pmtmr for high-res timesource
***** DMESG_NACH.TXT
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1563.511 MHz processor.
Using pmtmr for high-res timesource
*****
***** dmesg_vor.txt
audit: initializing netlink socket (disabled)
audit(1160051531.4294966247:0): initialized
Total HugeTLB memory allocated, 0
***** DMESG_NACH.TXT
audit: initializing netlink socket (disabled)
audit(1160042023.900:0): initialized
Total HugeTLB memory allocated, 0
*****
***** dmesg_vor.txt
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
evdev_connect: evdev effcdaa0 handle effcdabc name event0
evdev_connect: evdev effcd9a0 handle effcd9bc name event1
evdev_connect: evdev effcd8a0 handle effcd8bc name event2
***** DMESG_NACH.TXT
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
evdev_connect: evdev effcd9a0 handle effcd9bc name event0
evdev_connect: evdev effcdaa0 handle effcdabc name event1
evdev_connect: evdev effcd8a0 handle effcd8bc name event2
*****
***** dmesg_vor.txt
NET: Registered protocol family 23
via_ircc: module not supported by Novell, setting U taint flag.
Linux agpgart interface v0.100 (c) Dave Jones
***** DMESG_NACH.TXT
NET: Registered protocol family 23
Linux agpgart interface v0.100 (c) Dave Jones
*****
***** dmesg_vor.txt
agpgart: AGP aperture is 128M @ 0xd0000000
USB Universal Host Controller Interface driver v2.2
***** DMESG_NACH.TXT
agpgart: AGP aperture is 128M @ 0xd0000000
via_ircc: module not supported by Novell, setting U taint flag.
ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: irq 11, pci mem f161e000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.8-24.25-default ehci_hcd
usb usb1: SerialNumber: 0000:00:10.3
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
*****
***** dmesg_vor.txt
uhci_hcd 0000:00:10.0: irq 5, io base 0000d400
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.8-24.25-default uhci_hcd
usb usb1: SerialNumber: 0000:00:10.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[B] -> GSI 5 (level, low) -> IRQ 5
***** DMESG_NACH.TXT
uhci_hcd 0000:00:10.0: irq 5, io base 0000d400
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.8-24.25-default uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[B] -> GSI 5 (level, low) -> IRQ 5
*****
***** dmesg_vor.txt
uhci_hcd 0000:00:10.1: irq 5, io base 0000d800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.8-24.25-default uhci_hcd
usb usb2: SerialNumber: 0000:00:10.1
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 11 (level, low) -> IRQ 11
***** DMESG_NACH.TXT
uhci_hcd 0000:00:10.1: irq 5, io base 0000d800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.8-24.25-default uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 11 (level, low) -> IRQ 11
*****
***** dmesg_vor.txt
uhci_hcd 0000:00:10.2: irq 11, io base 0000dc00
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.8-24.25-default uhci_hcd
usb usb3: SerialNumber: 0000:00:10.2
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: irq 11, pci mem f168c000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
usb usb4: Product: EHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.8-24.25-default ehci_hcd
usb usb4: SerialNumber: 0000:00:10.3
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 4-5: new high speed USB device using address 3
usb 4-5: Product: USB TO IDE
usb 4-6: new high speed USB device using address 4
usb 4-6: Product: USB Mass Storage Device
usb 4-6: Manufacturer: Myson Century, Inc.
usb 4-6: SerialNumber: 100
usb 1-2: new full speed USB device using address 2
usb 1-2: Product: CanoScan
usb 1-2: Manufacturer: Canon
Initializing USB Mass Storage driver...
***** DMESG_NACH.TXT
uhci_hcd 0000:00:10.2: irq 11, io base 0000dc00
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.8-24.25-default uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
usb 1-5: new high speed USB device using address 3
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-5: Product: USB TO IDE
usb 1-6: new high speed USB device using address 4
usb 1-6: Product: USB Mass Storage Device
usb 1-6: Manufacturer: Myson Century, Inc.
usb 1-6: SerialNumber: 100
usb 2-2: new full speed USB device using address 2
usb 2-2: Product: CanoScan
usb 2-2: Manufacturer: Canon
Initializing USB Mass Storage driver...
*****
***** dmesg_vor.txt
sda: assuming drive cache: write through
sda:hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
sda1 sda2
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
***** DMESG_NACH.TXT
sda: assuming drive cache: write through
sda: sda1 sda2
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
*****
***** dmesg_vor.txt
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: SAMSUNG Model: SP2514N Rev: VF10
***** DMESG_NACH.TXT
scsi1 : SCSI emulation for USB Mass Storage devices
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Vendor: SAMSUNG Model: SP2514N Rev: VF10
*****
***** dmesg_vor.txt
Type: Direct-Access ANSI SCSI revision: 02
hdd: ATAPI 48X DVD-ROM drive, 254kB Cache
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
***** DMESG_NACH.TXT
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
*****
***** dmesg_vor.txt
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
USB Mass Storage device found at 4
***** DMESG_NACH.TXT
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
USB Mass Storage device found at 4
*****
***** dmesg_vor.txt
USB Mass Storage support registered.
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
st: Version 20040403, fixed bufsize 32768, s/g segs 256
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
***** DMESG_NACH.TXT
USB Mass Storage support registered.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
*****
***** dmesg_vor.txt
NET: Registered protocol family 17
BIOS EDD facility v0.16 2004-Jun-25, 3 devices found
***** DMESG_NACH.TXT
NET: Registered protocol family 17
hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 254kB Cache
st: Version 20040403, fixed bufsize 32768, s/g segs 256
BIOS EDD facility v0.16 2004-Jun-25, 3 devices found
*****
***** dmesg_vor.txt
powernow-k8: Processor cpuid 662 not supported
Non-volatile memory driver v1.2
Disabled Privacy Extensions on device eefb3c00(sit0)
eth0: no IPv6 routers present
end_request: I/O error, dev fd0, sector 72
***** DMESG_NACH.TXT
powernow-k8: Processor cpuid 662 not supported
eth0: no IPv6 routers present
Non-volatile memory driver v1.2
Disabled Privacy Extensions on device ed2cb000(sit0)
end_request: I/O error, dev fd0, sector 72
*****
Neusynchronisation fehlgeschlagen. Dateien sind zu verschieden.
***** dmesg_vor.txt
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
NTFS-fs warning (device sda2): parse_options(): Option iocharset is deprecated.Please use option nls=<charsetname> in the futur
.
NTFS volume version 3.1.
NTFS-fs warning (device sda2): parse_options(): Option iocharset is deprecated.Please use option nls=<charsetname> in the futur
.
NTFS volume version 3.1.
NTFS-fs warning (device sda2): parse_options(): Option iocharset is deprecated.Please use option nls=<charsetname> in the futur
.
NTFS volume version 3.1.
***** DMESG_NACH.TXT
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
usb 1-6: USB disconnect, address 4
usb 1-5: USB disconnect, address 3
usb 1-6: new high speed USB device using address 5
usb 1-6: Product: USB Mass Storage Device
usb 1-6: Manufacturer: Myson Century, Inc.
usb 1-6: SerialNumber: 100
scsi2 : SCSI emulation for USB Mass Storage devices
Vendor: SAMSUNG Model: SP2514N Rev: VF10
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: assuming drive cache: write through
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: assuming drive cache: write through
sda: sda1
Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi2, channel 0, id 0, lun 0, type 0
USB Mass Storage device found at 5
usb 1-5: new high speed USB device using address 6
usb 1-5: Product: USB TO IDE
scsi3 : SCSI emulation for USB Mass Storage devices
Vendor: Genesys Model: USB to IDE Disk Rev: 0033
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 117266688 512-byte hdwr sectors (60041 MB)
sdb: test WP failed, assume Write Enabled
sdb: assuming drive cache: write through
SCSI device sdb: 117266688 512-byte hdwr sectors (60041 MB)
sdb: test WP failed, assume Write Enabled
sdb: assuming drive cache: write through
sdb: sdb1 sdb2
Attached scsi removable disk sdb at scsi3, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi3, channel 0, id 0, lun 0, type 0
USB Mass Storage device found at 6
NTFS-fs warning (device sda1): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sdb2): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sda1): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sda1): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sda1): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sda1): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sda1): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will b
e case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will b
e case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will b
e case sensitive!
NTFS-fs warning (device sdb2): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sdb2): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sdb2): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sdb2): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sdb2): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sdb2): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sdb2): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sda1): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device sdb2): parse_options(): Option iocharset is deprecated.
Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will b
e case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will b
e case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will b
e case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
*****
ich hoffe Du kannst da da etwas draus erkennen, was mir helfen könnte.
Gruß Stradti
Hallo Oli,
hier kommt (hoffentlich) die komprimierte FileComapere-Datei
(wäre schön,, wenn Du mir weiterhelfennn könntest !)
Gruß Stradti
Um mal etwas Struktur in Deine Info zu bekommen:
Boote ohne die Platten angeklemmt zu haben, öffne im Anschluß eine Konsole und laß "tail -f /var/log/messages" laufen. Klemme dann die beiden Platten an und poste die daraufhin erfolgende Ausgabe, am besten per copy&paste unter Verwendung der vB-Tags aus meiner Sig. Das tail kannst Du mit <strg><c> abbrechen.
Zugleich poste bitte die Ausgabe von "cat /etc/fstab" und "mount", den mount-Befehl bitte nach dem Anklemmen der Platten ausführen.
Kreol
Beim posten von Dateien oder Ausgaben bitte [code]Text[/code] verwenden. Nähere Info über vB-Tags gibt es hier
I just want to know God's thoughts. The rest are details. (A. Einstein)
Hallo Kreol,
danke erst einmal für Deine Antwort.
hier kommen die Ausgaben:
vor dem Anstöpseln:
Oct 5 16:56:30 HajoLin xinetd[4459]: No such internal service: servers/stream - DISABLING
Oct 5 16:56:30 HajoLin xinetd[4459]: No such internal service: services/stream- DISABLING
Oct 5 16:56:30 HajoLin xinetd[4459]: bind failed (Address already in use (errno = 98)). service = pop3
Oct 5 16:56:30 HajoLin xinetd[4459]: Service pop3 failed to start and is deactivated.
Oct 5 16:56:30 HajoLin xinetd[4459]: xinetd Version 2.3.13 started with libwrap loadavg options compiled in.
Oct 5 16:56:30 HajoLin xinetd[4459]: Started working: 28 available services
Oct 5 16:56:38 HajoLin kdm: :0[4354]: pam_unix2: session started for user hajo01, service xdm-np
Oct 5 16:58:53 HajoLin su: (to root) hajo01 on /dev/pts/1
Oct 5 16:58:53 HajoLin su: pam_unix2: session started for user root, service su
Oct 5 16:59:01 HajoLin /usr/sbin/cron[4663]: (root) CMD ( rm -f /var/spool/cron/lastrun/cron.hourly)
nach dem Anstöpseln:
Oct 5 17:06:13 HajoLin /etc/dev.d/block/51-subfs.dev[5244]: mount block device/block/sda/sda1
Oct 5 17:06:15 HajoLin /etc/dev.d/block/50-hwscan.dev[5399]: new block device /block/sdb/sdb2
Oct 5 17:06:15 HajoLin /etc/dev.d/block/50-hwscan.dev[5400]: new block device /block/sdb/sdb1
Oct 5 17:06:15 HajoLin /etc/dev.d/block/51-subfs.dev[5415]: mount block device/block/sdb/sdb2
Oct 5 17:06:15 HajoLin /etc/dev.d/block/51-subfs.dev[5420]: mount block device/block/sdb/sdb1
Oct 5 17:06:16 HajoLin /etc/dev.d/block/50-hwscan.dev[5515]: new block device /block/sdb
Oct 5 17:06:16 HajoLin /etc/dev.d/block/51-subfs.dev[5526]: mount block device/block/sdb
Oct 5 17:06:25 HajoLin /etc/dev.d/block/51-subfs.dev[5244]: mount disk/by-path/usb-100:0:0:0p1
Oct 5 17:06:26 HajoLin /etc/dev.d/block/51-subfs.dev[5415]: mount disk/by-path/usb-0x05e3-0x0702:0:0:0p2
Oct 5 17:06:26 HajoLin /etc/dev.d/block/51-subfs.dev[5420]: mount disk/by-path/usb-0x05e3-0x0702:0:0:0p1
fstab hat dann folgende Einträge:
/dev/hdb2 / reiserfs acl,user_xattr 1 1
/dev/hda1 /windows/C vfat users,gid=users,umask=0002,iocharset=utf8 0 0
/dev/hda2 /windows/D ntfs ro,users,gid=users,umask=0002,nls=utf8 0 0
/dev/hda3 /windows/E ntfs ro,users,gid=users,umask=0002,nls=utf8 0 0
/dev/sda1 /windows/F ntfs ro,users,gid=users,umask=0002,nls=utf8 0 0
/dev/sdb1 /windows/G vfat users,gid=users,umask=0002,iocharset=utf8 0 0
/dev/sdb2 /windows/H ntfs ro,users,gid=users,umask=0002,nls=utf8 0 0
/dev/hdb1 swap swap pri=42 0 0
devpts /dev/pts devpts mode=0620,gid=5 0 0
proc /proc proc defaults 0 0
usbfs /proc/bus/usb usbfs noauto 0 0
sysfs /sys sysfs noauto 0 0
/dev/dvd /media/dvd subfs fs=cdfss,ro,procuid,nosuid,nodev,exec,iocharset=ut f8 0 0
/dev/dvdram /media/dvdram subfs fs=cdfss,ro,procuid,nosuid,nodev,exec,iocharset=ut f8 0 0
/dev/fd0 /media/floppy subfs fs=floppyfss,procuid,nodev,nosuid,sync 0 0
und mount zeigt das hier:
/dev/hdb2 on / type reiserfs (rw,acl,user_xattr)
proc on /proc type proc (rw)
tmpfs on /dev/shm type tmpfs (rw)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/hda1 on /windows/C type vfat (rw,noexec,nosuid,nodev,gid=100,umask=0002,iochars et=utf8)
/dev/hda2 on /windows/D type ntfs (ro,noexec,nosuid,nodev,gid=100,umask=0002,nls=utf 8)
/dev/hda3 on /windows/E type ntfs (ro,noexec,nosuid,nodev,gid=100,umask=0002,nls=utf 8)
/dev/hdd on /media/dvd type subfs (ro,nosuid,nodev,fs=cdfss,procuid,iocharset=utf8)
/dev/hdc on /media/dvdram type subfs (ro,nosuid,nodev,fs=cdfss,procuid,iocharset=utf8)
/dev/fd0 on /media/floppy type subfs (rw,nosuid,nodev,sync,fs=floppyfss,procuid)
/dev/sda1 on /media/usb-100:0:0:0p1 type subfs (rw,noexec,nosuid,nodev,sync,procuid,iocharset=utf 8)
/dev/sdb2 on /media/usb-0x05e3-0x0702:0:0:0p2 type subfs (rw,noexec,nosuid,nodev,sync,procuid,iocharset=utf 8)
/dev/sdb1 on /media/usb-0x05e3-0x0702:0:0:0p1 type subfs (rw,noexec,nosuid,nodev,sync,procuid,iocharset=utf 8)
Hoffentlich kanst Du mir da helfen,, denn ich habe nicht immer die Lust die externen Festplatten an- und wieder anzustöpslen.
Gruß und Dank
Stradti
Hallo Gemeinde,
das Problem ist gelöst. Im YAST unter System bin ich auf "Editor für /etc/sysconfig-Dateien" gegangen und habe unter Hardware/Hotplug den Eintrag "HOTPLUG_LOAD_MULTIPLE_MODULES" gewählt und den Wert von no auf yes gesetzt. Nach dem nächsten Booten wurden alle externe Festplatten korrekt angezeigt und ich kann darauf zugreifen.
Gruß Stradti
Berechtigungen
Zitieren
Lesezeichen