So, ich habe mal smartctl -a /dev/hda (Hier hda, weil mit Knoppix gebootet) ausgeführt.
Code:
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: HDS722580VLAT20
Serial Number: VNR2GEC2U0NPZL
Firmware Version: V32OA63A
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 3a
Local Time is: Sat Oct 22 20:35:06 2005 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 247) Self-test routine in progress...
70% of test remaining.
Total time to complete Offline
data collection: (1828) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 31) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 091 091 060 Pre-fail Always- 1966109
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline- 0
3 Spin_Up_Time 0x0007 113 113 024 Pre-fail Always- 175 (Average 178)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always- 131
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1883
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always- 0
8 Seek_Time_Performance 0x0005 100 100 020 Pre-fail Offline- 0
9 Power_On_Hours 0x0012 099 099 000 Old_age Always- 10367
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always- 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always- 131
192 Power-Off_Retract_Count 0x0032 100 100 050 Old_age Always- 539
193 Load_Cycle_Count 0x0012 100 100 050 Old_age Always- 539
194 Temperature_Celsius 0x0002 157 157 000 Old_age Always- 35 (Lifetime Min/Max 17/47)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always- 2261
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always- 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline- 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always- 3
SMART Error Log Version: 1
ATA Error Count: 164 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 164 occurred at disk power-on lifetime: 10365 hours (431 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 6e 5c ad 6f e6 Error: IDNF at LBA = 0x066fad5c = 107982172
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
39 00 a0 2a ad 6f e0 00 2d+01:35:49.900 WRITE MULTIPLE EXT
39 00 30 ca ac 6f e0 00 2d+01:35:49.800 WRITE MULTIPLE EXT
39 00 08 ba ac 6f e0 00 2d+01:35:49.800 WRITE MULTIPLE EXT
29 00 00 3f ae 54 e0 00 2d+01:35:49.800 READ MULTIPLE EXT
39 00 08 5a 16 6e e0 00 2d+01:35:49.800 WRITE MULTIPLE EXT
Error 163 occurred at disk power-on lifetime: 10365 hours (431 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 79 19 5e ca e3 Error: IDNF at LBA = 0x03ca5e19 = 63594009
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
39 00 a0 f2 5d ca e0 00 2d+01:31:28.000 WRITE MULTIPLE EXT
29 00 00 3f ec 33 e0 00 2d+01:31:27.900 READ MULTIPLE EXT
29 00 00 3f ea 33 e0 00 2d+01:31:27.800 READ MULTIPLE EXT
39 00 08 aa 03 ae e0 00 2d+01:31:27.800 WRITE MULTIPLE EXT
39 00 08 72 a8 6f e0 00 2d+01:31:27.800 WRITE MULTIPLE EXT
Error 162 occurred at disk power-on lifetime: 10365 hours (431 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 10 02 60 ca e3 Error: IDNF at LBA = 0x03ca6002 = 63594498
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
39 00 10 02 60 ca e0 00 2d+00:57:30.900 WRITE MULTIPLE EXT
39 00 70 a2 5f ca e0 00 2d+00:57:29.000 WRITE MULTIPLE EXT
39 00 08 7a 8d b1 e0 00 2d+00:57:24.100 WRITE MULTIPLE EXT
39 00 08 9a 5f ca e0 00 2d+00:57:24.000 WRITE MULTIPLE EXT
39 00 10 8a 5f ca e0 00 2d+00:57:24.000 WRITE MULTIPLE EXT
Error 161 occurred at disk power-on lifetime: 10365 hours (431 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 18 fa 5f ca e3 Error: IDNF at LBA = 0x03ca5ffa = 63594490
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
39 00 70 a2 5f ca e0 00 2d+00:57:29.000 WRITE MULTIPLE EXT
39 00 08 7a 8d b1 e0 00 2d+00:57:24.100 WRITE MULTIPLE EXT
39 00 08 9a 5f ca e0 00 2d+00:57:24.000 WRITE MULTIPLE EXT
39 00 10 8a 5f ca e0 00 2d+00:57:24.000 WRITE MULTIPLE EXT
39 00 08 52 83 c9 e0 00 2d+00:57:19.400 WRITE MULTIPLE EXT
Error 160 occurred at disk power-on lifetime: 10365 hours (431 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 05 ed 3d ca e3 Error: IDNF at LBA = 0x03ca3ded = 63585773
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
39 00 10 e2 3d ca e0 00 2d+00:54:14.000 WRITE MULTIPLE EXT
39 00 10 e2 3d ca e0 00 2d+00:54:12.800 WRITE MULTIPLE EXT
39 00 a0 52 3c ca e0 00 2d+00:54:12.100 WRITE MULTIPLE EXT
39 00 08 5a ee ad e0 00 2d+00:54:12.100 WRITE MULTIPLE EXT
39 00 08 92 e3 ad e0 00 2d+00:54:12.100 WRITE MULTIPLE EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging
Leider kann ich damit nichts anfangen.
Könnte mir vielleicht jemand die Ausgabe erklären?
Big THX.
Lesezeichen