USB-Stick will einfach nicht

**juergen123** · 28.01.05, 18:44

Hallo,

ich habe einen neuen Stick und bekomme das Teil einfach nicht zum laufen. Ein anderer Stick sowie meine Digicam und der Drucker funzen an dem Rechner.
Der Stick funzt auch unter Win. Nur unter Linux nicht.

Hier die Meldung des Kernel mit: tail -f /var/log/messages

Code:

Jan 28 18:44:08 linux kernel: hub.c: new USB device 00:03.1-2, assigned address 6
Jan 28 18:44:08 linux kernel: usb.c: USB device not accepting new address=6 (error=-110)
Jan 28 18:44:09 linux kernel: hub.c: new USB device 00:03.1-2, assigned address 7
Jan 28 18:44:09 linux kernel: usb.c: USB device not accepting new address=7 (error=-110)

"modprobe usb-storage" nutzt auch nichts

ich habe SuSe 9.0 Prof mit Kernel 2.4

Vielen Dank für Eure Hilfe!

Gruß
Jürgen

**juergen123** · 30.01.05, 21:17

Hat niemand einen guten Rat für mich ?

Ich komme allein nicht mehr weiter...

Gruß
Jürgen

**ProfBunny** · 30.01.05, 21:23

hi,

was sagt den lsusb zu den teil?

mfg

**juergen123** · 30.01.05, 21:44

Hallo,

lsusb sagt:

Code:

linux:/home/Juergen # lsusb
Bus 003 Device 001: ID 0000:0000
Bus 003 Device 002: ID 03f0:1104 Hewlett-Packard Deskjet 959C
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
linux:/home/Juergen #

dmesg sagt:

Code:

linux:/home/Juergen # dmesg
Linux version 2.4.21-273-athlon (root@i386.suse.de) (gcc version 3.3.1 (SuSE Linux)) #1 Mon Jan 17 13:03:46 UTC 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
 BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
 BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
 BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
501MB vmalloc/ioremap area available.
0MB HIGHMEM available.
511MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 AMI                        ) @ 0x000fab80
ACPI: RSDT (v001 AMIINT SiS740XX 00000.04096) @ 0x1fff0000
ACPI: FADT (v001 AMIINT SiS740XX 00000.00017) @ 0x1fff0030
ACPI: MADT (v001 AMIINT SiS740XX 00000.04096) @ 0x1fff00c0
ACPI: DSDT (v001    SiS      746 00000.00256) @ 0x00000000
ACPI: Skipping APIC setup
Kernel command line: root=/dev/hda3 vga=0x31a desktop hdc=ide-scsi hdclun=0 splash=silent
ide_setup: hdc=ide-scsi
ide_setup: hdclun=0
bootsplash: silent mode.
Building zonelist for node : 0
Initializing CPU#0
Detected 1916.293 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 3792.89 BogoMIPS
Memory: 514260k/524224k available (1732k kernel code, 9576k reserved, 606k data, 176k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU:             Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU: AMD Athlon(tm) XP 2600+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20030619
PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=2
PCI: Using configuration type 1
Looking for DSDT in initrd ... not found!
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15)
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
00:00:01[A] -> IRQ 11 Mode 1 Trigger 1
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
00:00:01[B] -> IRQ 10 Mode 1 Trigger 1
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
00:00:01[C] -> IRQ 5 Mode 1 Trigger 1
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PIC: IRQ (11) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (10) already programmed
PIC: IRQ (5) already programmed
PIC: IRQ (11) already programmed
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 3
00:00:03[A] -> IRQ 3 Mode 1 Trigger 1
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5
PIC: IRQ (5) already programmed
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
PIC: IRQ (10) already programmed
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
PIC: IRQ (10) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (10) already programmed
PIC: IRQ (5) already programmed
PIC: IRQ (10) already programmed
PIC: IRQ (5) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (5) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (10) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (10) already programmed
PIC: IRQ (5) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (10) already programmed
PIC: IRQ (5) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (10) already programmed
PIC: IRQ (5) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (5) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (11) already programmed
PIC: IRQ (10) already programmed
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd
bigpage subsystem: allocated 0 bigpages (=0MB).
kinoded started
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 32764
aio_setup: sizeof(struct page) = 48
vesafb: framebuffer at 0xc0000000, mapped to 0xe0817000, size 65536k
vesafb: mode is 1280x1024x16, linelength=2560, pages=1
vesafb: protected mode interface info at c000:f090
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.0.9-2003/09/08: looking for picture.... silenjpeg size 30981 bytes, found (1280x1024, 15663 bytes, v3).
bootsplash: silent jpeg found.
bootsplash: silent jpeg found.
Console: switching to colour frame buffer device 148x51
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 16 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
    ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6Y120L0, ATA DISK drive
blk: queue c03e86c0, I/O limit 4095Mb (mask 0xffffffff)
hdc: ATAPI CD-RW 52XMax, ATAPI CD/DVD-ROM drive
hdd: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=14593/255/63, UDMA(133)
ide-floppy driver 0.99.newide
Partition check:
 hda: hda1 hda2 hda3
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
cryptoapi: loaded
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 291k freed
VFS: Mounted root (ext2 filesystem).
reiserfs: found format "3.6" with standard journal
reiserfs: enabling write barrier flush mode
reiserfs: using ordered data mode
reiserfs: checking transaction log (device ide0(3,3)) ...
for (ide0(3,3))
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
hda: cache flushing failed. disable write back cacheing for journalled file systems
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
hda: cache flushing failed. disable write back cacheing for journalled file systems
Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 176k freed
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
reiserfs: enabling write barrier flush mode
device-mapper: 4.0.1-ioctl (2003-07-12) initialised: dm@uk.sistina.com
reiserfs: enabling write barrier flush mode
reiserfs: enabling write barrier flush mode
lvm-mp: allocating 42 lowmem entries at c2a02000
LVM version 1.0.5+(mp-v6d)(22/07/2002) module loaded
reiserfs: enabling write barrier flush mode
reiserfs: enabling write barrier flush mode
reiserfs: enabling write barrier flush mode
NTFS driver 2.1.4a [Flags: R/O MODULE].
NTFS volume version 3.1.
Adding Swap: 1036184k swap-space (priority 42)
hdd: attached ide-cdrom driver.
hdd: ATAPI 16X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
  Vendor: ATAPI     Model: CD-RW52XMAX       Rev: 1.0
  Type:   CD-ROM                             ANSI SCSI revision: 02
bootsplash: silent jpeg found.
sis900.c: v1.08.06 9/24/2002
eth0: Realtek RTL8201 PHY transceiver found at address 1.
eth0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xdc00, IRQ 11, 00:0b:6a:14:d0:e0.
eth0: Media Link On 100mbps full-duplex
raw1394: /dev/raw1394 device initialized
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci_hcd 00:03.2: PCI device 1039:7002 (Silicon Integrated Systems [SiS])
ehci_hcd 00:03.2: irq 10, pci mem e48e8000
usb.c: new USB bus registered, assigned bus number 1
PCI: 00:03.2 PCI cache line size set incorrectly (32 bytes) by BIOS/FW.
PCI: 00:03.2 PCI cache line size corrected to 64.
ehci_hcd 00:03.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
hub.c: USB hub found
hub.c: 6 ports detected
usb-uhci.c: $Revision: 1.275 $ time 13:38:10 Jan 17 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
uhci.c: USB Universal Host Controller Interface driver v1.1
usb-ohci.c: USB OHCI at membase 0xe48ea000, IRQ 5
usb-ohci.c: usb-00:03.1, Silicon Integrated Systems [SiS] 7001 (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xe48ec000, IRQ 3
usb-ohci.c: usb-00:03.0, Silicon Integrated Systems [SiS] 7001
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 3 ports detected
mice: PS/2 mouse device common for all mice
hub.c: new USB device 00:03.0-2, assigned address 2
usb.c: USB device 2 (vend/prod 0x3f0/0x1104) is not claimed by any active driver.
hub.c: new USB device 00:03.1-2, assigned address 2
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: new USB device 00:03.1-2, assigned address 3
usb.c: USB device not accepting new address=3 (error=-110)
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 0x/52x writer cd/rw xa/form2 cdda tray
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU1] (supports C1)
IPsec Security Association Database (SADB): initialized.
IPsec Security Policy Database (SPD): initialized.
IPsec PF_KEY V2: initialized
IPv6 v0.8 (usagi-cvs/IPsec6 based StS) for NET4.0
IPv6 over IPv4 tunneling driver
usb.c: registered new driver usblp
printer.c: Disabling reads from problem bidirectional printer on usblp0
printer.c: usblp0: USB Unidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1104
printer.c: v0.11: USB Printer Device Class driver
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
bootsplash: silent jpeg found.
lp0: using parport0 (polling).
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
eth0: no IPv6 routers present
hub.c: new USB device 00:03.2-4, assigned address 2
usb.c: USB device 2 (vend/prod 0xea0/0x2168) is not claimed by any active driver.
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module  1.0-4496  Wed Jul 16 19:03:09 PDT 2003
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi1 : SCSI emulation for USB Mass Storage devices
  Vendor:           Model:                   Rev: 2.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Trying generic SiS routines for device id: 0746
agpgart: AGP aperture is 128M @ 0xd0000000
SCSI device sda: 128000 512-byte hdwr sectors (66 MB)
sda: Write Protect is off
 sda: sda1
Linux video capture interface: v1.00
usb.c: USB disconnect on device 00:03.2-4 address 2
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 08
Info fld=0xa00 (nonstd), Current sd00:00: sense key Not Ready
sda : block size assumed to be 512 bytes, disk size 1GB.
sda: test WP failed, assume Write Enabled
 sda: I/O error: dev 08:00, sector 0
 I/O error: dev 08:00, sector 0
 I/O error: dev 08:00, sector 2097144
 I/O error: dev 08:00, sector 2097144
 I/O error: dev 08:00, sector 0
 I/O error: dev 08:00, sector 0
 unable to read partition table
 I/O error: dev 08:00, sector 0
bootsplash: silent jpeg found.
hub.c: new USB device 00:03.1-2, assigned address 4
usb.c: USB device not accepting new address=4 (error=-110)
hub.c: new USB device 00:03.1-2, assigned address 5
usb.c: USB device not accepting new address=5 (error=-110)
linux:/home/Juergen #

Ich hoffe damit kann jemand was anfangen. Ich bin mit meinem Latein am Ende.

Gruß

Jürgen

**ProfBunny** · 30.01.05, 22:04

hi,

bei mir gibts aus
Bus 001 Device 003: ID 126f:2168 TwinMOS Mobile Disk III

wenn du noch auf 2.4.x fährst wäre zu empfehlen mal den 2.6.x zu testen, da hat sich doch einiges getan in richtung usb devices.

mehr kann ich auch nicht sagen. evtl noch ein
cat /proc/bus/usb/devices

sonst ist alle.

PS: meinstick läuft auch nur mit 2.6.x kernels

mfg

**amues** · 31.01.05, 19:00

Hallo zusammen !

Ich hatte ein ähnliches Problem mit einem No Name USB Stick.
Mit modconf bei Debian hatte ich das Modul für USB 2 Support entfernt
und dann ging es wunderbar. (nach langer Suche und probieren)
Leider nistete sich das Modul immer wieder neu ein.
-> mit modconf Modul entladen
-> Modul gelöscht + update-modules = ruhe
-> Module sind in /lib/modules/2.4.27-1-k7/kernel/drivers/usb

**juergen123** · 31.01.05, 20:35

Hallo,

danke für die Tips. Leider bin ich noch nicht weiter.
Ich hab noch nie einen Kernel gebacken, aber das kann man ja nachlesen. Ich hab nur keinen Bock, die Kiste komplett neu zu machen...

cat /proc/bus/usb/devices:

Code:

juergen@linux:~> cat /proc/bus/usb/devices
T:  Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 3
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 0.00
S:  Product=USB OHCI Root Hub
S:  SerialNumber=e48ec000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms
T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=03f0 ProdID=1104 Rev= 1.00
S:  Manufacturer=Hewlett-Packard
S:  Product=DeskJet 950C
S:  SerialNumber=ES12R19111DF
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  2mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=01 Driver=usblp
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:  If#= 0 Alt= 1 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=usblp
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 3
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 0.00
S:  Product=USB OHCI Root Hub
S:  SerialNumber=e48ea000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 6
B:  Alloc=  0/800 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.04
S:  Manufacturer=Linux 2.4.21-273-athlon ehci_hcd
S:  Product=PCI device 1039:7002 (Silicon Integrated Systems [SiS])
S:  SerialNumber=00:03.2
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=256ms
juergen@linux:~>

Ich habe den Stick unter Knoppix mit 2.6er Kernel versucht. Auch nix... Daher sehe ich die Chancen nicht gut, daß er unter meinem Linux mit dem 2.6er rennt.

@amues
Welches sind die Module für den 2.0 Support? Da stehen viele drin...
Danke!

Gruß
Jürgen

**amues** · 01.02.05, 17:13

Hallo zusammen !

Es heißt ehci-hcd und befindet sich in:

/lib/modules/2.4.27-1-k7/kernel/drivers/usb/host

Wie schon erwähnt ich benutze Debian und dort gibt es zur
Modul Konfiguration das Programm modconf ,
bei dir dann eventuell mit Yast.

**juergen123** · 03.02.05, 20:35

Ich komme leider nicht weiter.

Hat noch jemand einen Tip für mich?

Gruß

Jürgen

**amues** · 17.02.05, 18:09

Hallo zusammen !

Habe den Namen des störenden Moduls noch gefunden !
(siehe geänderten Beitrag)
Beim Kernel Update war es wieder dabei und der USB Stick
konnte wieder nicht eingebunden werden.(Kernel 2.4.27-2-k7)
Nach dem oben beschriebenen Verfahren funktionierte er wieder wie immer.

**UTGMK** · 03.03.05, 15:12

Also ich finde es imer wieder traurig, dass so viele Probleme mit USB Geräten auftreten. Das kann ja wohl nicht so schwer sein, dass ordnetlich hin zu bekommen?? Oder lieg ich da falsch??

Also mir geht es da zumindest so ich will meine USB Stick reinstecken und benutzen können! Und nicht 5 Stunden lang irgendwo in Konfigdateien herum zu suchen.