Hi zusammen
Ich habe eben mal wieder die Erfahrung gemacht das Hardware nicht ewig hält.
Und zwar folgendes:
In meinem System nutze ich verschiedene Partitionen fürs Filesharing (nur legales
versteht sich). o_0 Nu is mir aufgefallen das alle rar Archive die ich runter lade defekt
sind. Darauf hin habe ich mit smartctl die Platte gecheckt und ne menge Errormeldungen
bekommen.
Code:
server:/# smartctl -a /dev/hda
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG SV2044D
Serial Number: 0218J1FN584013
Firmware Version: MM200-52
Device is: In smartctl database [for details use: -P show]
ATA Version is: 4
ATA Standard is: ATA/ATAPI-4 T13 1153D revision 17
Local Time is: Thu Jul 29 17:18:04 2004 CEST
==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details.
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 960) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 16) minutes.
SMART Attributes Data Structure revision number: 9
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000a 100 100 051 Old_age Always - 15
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2798
5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000a 253 253 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 253 253 000 Old_age Offline - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1250812
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1533
197 Current_Pending_Sector 0x0032 253 253 010 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 253 253 010 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 051 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 100 100 051 Old_age Always - 0
SMART Error Log Version: 1
Warning: ATA error count 235 inconsistent with error log pointer 2
ATA Error Count: 235 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 235 occurred at disk power-on lifetime: 10422 hours (434 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 88 00 00 4f c2 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 da 00 00 4f c2 e0 00 49d+12:44:33.296 SMART RETURN STATUS
20 00 08 5f 50 b0 e0 00 49d+12:44:33.296 READ SECTOR(S)
20 00 08 a7 00 b0 e0 00 49d+12:44:33.296 READ SECTOR(S)
20 00 08 ef 29 b0 e0 00 49d+12:44:33.296 READ SECTOR(S)
ec 00 00 66 00 20 e0 00 49d+12:44:33.296 IDENTIFY DEVICE
Error 234 occurred at disk power-on lifetime: 8765 hours (365 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 80 00 3f 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
de 00 00 3f 00 00 a0 00 00:00:35.000 MEDIA LOCK
ca 00 01 3f 00 00 e0 00 00:00:35.000 WRITE DMA
c8 00 08 6d 65 18 e0 00 00:00:35.000 READ DMA
c8 00 40 95 4d 19 e0 00 00:00:35.000 READ DMA
c8 00 40 6d 65 18 e0 00 00:00:35.000 READ DMA
Error 233 occurred at disk power-on lifetime: 8765 hours (365 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 80 00 9c 3c 22 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
de 00 00 9c 3c 22 a0 00 00:00:30.000 MEDIA LOCK
c8 00 08 95 3c 22 e0 00 00:00:30.000 READ DMA
c8 00 25 95 3c 22 e0 00 00:00:30.000 READ DMA
c8 00 08 a5 d6 0f e0 00 00:00:30.000 READ DMA
c8 00 08 5d 6f 09 e0 00 00:00:30.000 READ DMA
Error 232 occurred at disk power-on lifetime: 8765 hours (365 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 80 00 3f 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
de 00 00 3f 00 00 a0 00 00:00:31.000 MEDIA LOCK
ca 00 01 3f 00 00 e0 00 00:00:31.000 WRITE DMA
c8 00 08 6d 65 18 e0 00 00:00:31.000 READ DMA
c8 00 40 95 4d 19 e0 00 00:00:31.000 READ DMA
c8 00 40 6d 65 18 e0 00 00:00:31.000 READ DMA
Error 231 occurred at disk power-on lifetime: 8765 hours (365 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 80 00 61 08 0f a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d5 01 01 4f c2 e0 00 49d+13:13:46.296 SMART READ LOG
b0 d1 01 01 4f c2 e0 00 49d+13:13:46.296 SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
b0 d0 01 00 4f c2 e0 00 49d+13:13:46.296 SMART READ DATA
b0 da 00 00 4f c2 00 00 49d+13:13:46.296 SMART RETURN STATUS
b0 da 00 00 4f c2 e0 00 49d+13:13:46.296 SMART RETURN STATUS
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging
Wie man sieht ne menge *******e
Hat einer von euch ne Ahnung wie ich das noch hinbiegen kann?
Danke schonmal
bye
sxe
Lesezeichen