hallo allerseits,
hab da ein kleines problem mit yaps... ich habe hier ein notebook mit ne avm fritzcard und suse 9.1. das notebook überwacht mit hilfe von nagios das netz und soll über yaps ne sms rausschicken wenn server x down geht. das ganze funktioniert bereits wunderbar mit modem. allerdings mit isdn kriege ich des net hin.
mein hauptproblem ist das ich nicht weiß welches device die karte hat.. modem kann ich ja unter /dev/modem ansprechen.... aber wo finde ich die isdn karte..bzw was/wie muss ich configurieren .... jemand ne idee wie ich da weiterkomme...
hier noch meine momentane yaps.rc für modem ^^
----------------------------------------------------------------------------------------------
# -*- sh -*-
#
# General yaps example configuration file
#
#########################################
# global section #
#########################################
#
# This is a comma seperated list of available services. This
# is required for autodetect the matching service for a
# pager-id
services D1-0160, D1-0170, D1-0171, D1-0175
+services D2-0172, D2-0173, D2-0174, D2-0174
+services E+0177, E+0178
+services Telmi,Telmi-Fun,Telmi-Family,Telmi-Top,Telmi-Pro
+services Skyper,Quix
#
# This is the default caller-id. If the protocol/service allowes
# it, this is inserted in the message (and the receiver gets this
# as the sender's number)
call-id 0123-4567890
#
# If you forget to sign your message, you can automatically append
# this string to each message.
signature NAME
#
# You can either switch the use of the signature here on for all
# services or in each service section for that particular service.
#use-signature True
#
# To get more verbose output when running yaps increase this value.
# Currently 4 is the highest supported value.
verbose 4
#
# If you'd like to log every sending session define this. It should
# point to a writeable file. If you install the software setgid, then
# change the group of this file to the same yaps uses and make it
# group writeable.
logfile /var/log/yaps.log
#
# A comma seperated list of modem sections. You can also define this
# in each service section.
modems standard
#
# some global defaults for the serial interface (even if the most
# protocols are assuming 7e1, these settings seem to work well)
speed 38400
bits-per-byte 8
parity none
stopbits 1
#
# To calculate the cost for each call, you can define some globales
# here and do the fine tuning in each protocol
cost cost=0.12,unit=DM,remainder=2,dial-overhead=13
#
# These are two example of internal conversion tables. The can be
# used using the `convert' entry (see below).
cv-default {
�[
�\
�]
�{
�|
}
�~
}
cv-extend {
\l \s
\n \s
\r \s
\f \s
\t \s
}
#
# These values are normally only found in each service section,
# but are listen here with an explaination for completeness.
#
# This is the phone number of the modem gateway for this service
#phone 0015559876
#
# This is the protocol the service uses. Currently this can be
# either ascii, script, ucp or tap. Each protocol has a set of
# special configuration parameters, see below.
#protocol tap
#
# Most services limit the length of a message to a specific length.
# Enter the value here to check valid messages
max-size 160
#
# If a message is longer than max-size, you can set this to split
# it off into several single messages of allowed length
may-split True
#
# If a message is longer than max-size, you can set this to truncate
# the message to the allowed length. The remaining part is discarded.
#truncate True
#
# Some services allow to send more than one message per session. If
# it is limited, set it using this parameter
#max-messages 1
#
# If the service allows using your caller-id set this to True.
use-call-id True
#
# If the service is reachable over a phonenumber where the pager-id
# is part of the phone number, define this and add a `%P' anywehere
# in the `phone' number.
#insert-pager-id True
#
# Remove these characters from the pager-id, as they are not valid
rm-invalids-pid + (-)
#
# Dito for caller id
rm-invalids-cid + (-)
#
# Check for valid call id (see below for more details) While
# valid-pid is required, this is optional
#valid-cid ^(001|1)
#change-cid 001
#
# Depending on your system the value for this parameter is either a
# regular expression or a simple list of strings (seperated by bars)
# which must match the prefix of the pager-id.
#valid-pid ^(0171|0049171)
#valid-pid 0171|0049171
# Use these paramters in the global section if you want do not want
# to check pager-ids (and do not set change-pid):
#valid-pid .
#valid-pid -
#
# If a pagerid has matched the expression above, then the matching part
# may be replaced by this string
#change-pid 0171
#
# As the services do not use (in general) the ISO 8859/1 character set,
# one can define convertion tables. you can either specify a file which
# contains the convertion rules:
#conv-table /usr/local/lib/yaps/iso2din.tab
# or use predefined convertion rules
#convert *no-control,*no-8bit,cv-default,cv-extended
#
# If this is set, send a message even if a requested feature is
# not available
#force True
#
# If the provider supportes to set a delay for sending the message,
# set this
#can-delay True
#
# If the provider can delete a buffered message after a period of time,
# set this
#can-expire True
#
# If the provider can report a delivery status, set this.
#can-rds True
#
# To check wether a call-id/pager-id is valid use these paramters.
# For the exact syntax see the documentation
#check-call-id >1111111111111111<
#check-pager-id >1111111111111111<
#check-call-id +minimum=0,maximum=16,type=numeric
#
# These values are typically found in a modem section, but can also
# appear in the global section to set some defaults
#
# Set this to the modem device you wish to use
#device /dev/modem
device /dev/ttyS0
#device /dev/ttyI5
#device /dev/cua1
#device /dev/cua/a
#
# Set this to the prefix of the lockfile use for the device. There
# are several places, and two common formats:
#lock-prefix /usr/spool/uucp/LCK..
lock-prefix /var/spool/lock/LCK..
#lock-prefix /var/spool/locks/LK.
#
# The different format of the part which is appended to the lockfile
# and the contents can be specified here. See documentation for a
# full list inclusive explaination
#lock-method sysv4
#lock-method binary
#lock-method timeout=10
#
# These are send/expect sequences to talk to the modem. For an exact
# definition see (again) the documentation. Following entries are
# supported:
# init: to initialize the modem
# local-init: a second initialization string, used to customize
# already defined modems for different handling
# dial: to dial a phone number %L is replaced with the
# phone number itself
# timeout: the default timeout in seconds to wait for answers
# reset: to reset the modem
#########################################
# service section #
#########################################
#
# D1 (by Deutsche Telekom)
#
[D1-0160]
protocol tap
valid-pid 0160|0049160|49160
#change-pid 0160
convert *no-8bit,cv-d1
cv-d1 {
�[
�\
�~
�{
�|
~
�^]
}
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
phone 01712092522
# use this number for isdn-dialin:
# phone 01712521001
max-size 160
may-split True
use-call-id False
tap-old True
#
#----------------------------------------------------------
#
[D1-0170]
protocol tap
valid-pid 0170|0049170|49170
change-pid 0170
convert *no-8bit,cv-d1
cv-d1 {
�[
�\
�~
�{
�|
~
�^]
}
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
phone 01712092522
# use this number for isdn-dialin:
# phone 01712521001
max-size 160
may-split True
use-call-id False
tap-old True
#
#----------------------------------------------------------
#
[D1-0171]
protocol tap
valid-pid 0171|0049171|49171
change-pid 0171
convert *no-8bit,cv-d1
cv-d1 {
�[
�\
�~
�{
�|
~
�^]
}
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
phone 01712092522
# use this number for isdn-dialin:
# phone 01712521001
max-size 160
may-split True
use-call-id False
tap-old True
#
#----------------------------------------------------------
#
[D1-0175]
protocol tap
valid-pid 0175|0049175|49175
change-pid 0175
convert *no-8bit,cv-d1
cv-d1 {
�[
�\
�~
�{
�|
~
�^]
}
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
phone 01712092522
# use this number for isdn-dialin:
# phone 01712521001
max-size 160
may-split True
use-call-id False
tap-old True
#
#----------------------------------------------------------
#
#
# D2 (by Mannesmann Mobilfunk)
#
[D2-0162]
modem standard
protocol ucp
valid-pid 0162|0049162|49162
change-pid 0162
convert *no-8bit,cv-default
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
# phone 01722278020
# use this number for isdn-dialin:
phone 01722278010
max-size 160
may-split True
use-call-id True
can-delay True
can-expire True
can-rds True
check-call-id >1111111111111111<
check-pager-id >1111111111111111<
ucp-extend True
#
#----------------------------------------------------------
#
[D2-0172]
modem standard
protocol ucp
valid-pid 0172|0049172|49172
change-pid 0172
convert *no-8bit,cv-default
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
# phone 01722278020
# use this number for isdn-dialin:
phone 01722278010
max-size 160
may-split True
use-call-id True
can-delay True
can-expire True
can-rds True
check-call-id >1111111111111111<
check-pager-id >1111111111111111<
ucp-extend True
#
#----------------------------------------------------------
#
[D2-0173]
modem standard
protocol ucp
valid-pid 0173|0049173|49173|173
change-pid 0173
convert *no-8bit,cv-default
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
# phone 01722278020
# use this number for isdn-dialin:
phone 01722278010
max-size 160
may-split True
use-call-id True
can-delay True
can-expire True
can-rds True
check-call-id >1111111111111111<
check-pager-id >1111111111111111<
ucp-extend True
#
#----------------------------------------------------------
#
[D2-0174]
modem standard
protocol ucp
valid-pid 0174|0049174|49174|174
change-pid 0174
convert *no-8bit,cv-default
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
# phone 01722278020
# use this number for isdn-dialin:
phone 01722278010
max-size 160
may-split True
use-call-id True
can-delay True
can-expire True
can-rds True
check-call-id >1111111111111111<
check-pager-id >1111111111111111<
ucp-extend True
#
#----------------------------------------------------------
#
#
#
# E+ (by ???)
# !! UNTESTED !!
#
[E+0177]
protocol tap
valid-pid 0177|0049177|49177
change-pid 0177
convert *no-8bit,cv-default
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
phone 01771167
max-size 160
may-split True
use-call-id False
#
#----------------------------------------------------------
#
[E+0178]
protocol tap
valid-pid 0178|0049178|49178|0178|0163|0049163|49163
#change-pid 0178
convert *no-8bit,cv-default
+cost timetable=Wk0800-1800=5.7;Wk1800-0800=11.4;Ss=11.4
phone 01771167
max-size 160
may-split True
use-call-id False
#
#----------------------------------------------------------
#
#
# Telmi, Telmi-* (by Deutsche Funkruf)
# !! ONLY TESTED FOR TELMI-FUN !!
#
[Telmi]
protocol tap
valid-pid 01661|01665|00491661|00491665|491661|491665
change-pid -
convert *no-control,*no-8bit,cv-default,cv-extend
+cost entity-length=5.2
phone 016601010101
max-size 114
may-split True
max-messages 1
use-call-id False
check-pager-id 1111111
tap-old True
[Telmi-Fun] Telmi
[Telmi-Family] Telmi
[Telmi-Top] Telmi
max-size 240
[Telmi-Pro] Telmi-Top
#
# Skyper (by Deutsche Telekom)
# !! UNTESTED !!
#
[Skyper]
protocol tap
valid-pid 01692|00491692|491692
change-pid -
convert *no-8bit,cv-default,cv-extend
+cost fixed,cost=0.96
phone 01692%P
max-size 80
use-call-id False
insert-pager-id True
#
# Quix (by Miniruf)
# !! UNTESTED !!
#
[Quix]
protocol ucp
valid-pid 01653|00491653|491653
change-pid -
+cost fixed,timetable=Wk0800-1800=1.20;Al=0.96
convert *no-8bit,cv-default,cv-extend
phone 016593
max-size 80
use-call-id True
#########################################
# modem section #
#########################################
[standard]
#
# Locking
#
# Older Unix versions
#lock-prefix /usr/spool/uucp/LCK..
# Newer Unix versions
#lock-prefix /var/spool/uucp/LCK..
lock-prefix /var/spool/locks/LCK..
# SysV4
#lock-prefix /var/spool/locks/LK.
#lock-method sysv4
#
# Device
#
# Typical a symbolic link to the real device
device /dev/modem
# "normal" call-out device
#device /dev/cua1
# Solaris convention
#device /dev/cua/a
# use the following device for isdn-dialout:
#device /dev/ttyI6
#
#
# Modem talk
#
#init \\r !200D AT&F2\r <OK ATE0Q0V1M1L1X3\r <OK
#init \\r !200D AT&F2\r <OK ATV1M1L1X3\r <OK
init \\r !200D ATZ\r <OK
# use the following init-string for isdn:
# and change MSN to your MSN (what else...:-))
#init \\r !200D ATZ\r <OK AT&E9879356\r <OK
dial ATDT0,%L\r <60CONNECT|OK|BUSY|NO\sDIALTONE|NO\sCARRIER
reset ATH\r <OK
timeout 10
# Customizing an existing modem entry
#[standard-d2] standard
#local-init AT\%C2\r <OK
#
# alias section
#
[alias]
#name tel
admins 0171xxxxxxxxxxxxxxx
