-13-
30.01.03, 15:14
Habe folgendes Problem wozu ich hier im forum noch keine fehlerlösung gefunden habe.
Und zwar habe ich unter gentoo keine mouse. Habe eine "Microsoft Wireless Optical Mouse Blue" (welch ein schweres Wort :)) Habe bei kernel kompilieren meine Red Hat Config verglichen und USB soweit meiner meinung nach richtig eingestellt. Habe die USB Module fest geladen. Sooooo. Erkannt wird diese auch meiner meinung nach richtig beim start. Habe hier mal die message :
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
hcd.c: ehci-hcd @ 00:1d.7, Intel Corp. 82801DB USB EHCI Controller
hcd.c: irq 3, pci mem e0848000
usb.c: new USB bus registered, assigned bus number 1
ehci-hcd.c: restricting 64bit DMA mappings to segment 0 ...
ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0
hub.c: USB hub found
hub.c: 6 ports detected
usb-uhci.c: $Revision: 1.275 $ time 05:47:42 Dec 12 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 4
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
hub.c: USB new device connect on bus4/1, assigned device number 2
usb-uhci.c: interrupt, status 3, frame# 552
hiddev0: USB HID v1.00 Gamepad [Microsoft SideWinder Game Voice] on usb4:2.0
hub.c: USB new device connect on bus4/2, assigned device number 3
usb.c: USB device 3 (vend/prod 0x3f0/0x3002) is not claimed by any active driver.
hub.c: USB new device connect on bus2/1, assigned device number 2
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: USB new device connect on bus2/2, assigned device number 3
usb-uhci.c: interrupt, status 3, frame# 258
input0: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse® 1.0A] on usb2:3.0
hub.c: USB new device connect on bus2/1/1, assigned device number 4
input1: USB HID v1.00 Joystick [Microsoft Microsoft SideWinder Precision Pro (USB)] on usb2:4.0
hub.c: USB new device connect on bus2/1/2, assigned device number 5
usb.c: USB device 5 (vend/prod 0x733/0x401) is not claimed by any active driver.
hub.c: USB new device connect on bus2/1/3, assigned device number 6
usb.c: registered new driver usblp
printer.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 1 proto 2 vid 0x03F0 pid 0x3002
Aber irgendwie funktioniert die nicht. Kann in der XF86Config auswählen was ich will bei dem Device. Aber nix regt sich :( Hat jemand einen Rat für mich??
Und zwar habe ich unter gentoo keine mouse. Habe eine "Microsoft Wireless Optical Mouse Blue" (welch ein schweres Wort :)) Habe bei kernel kompilieren meine Red Hat Config verglichen und USB soweit meiner meinung nach richtig eingestellt. Habe die USB Module fest geladen. Sooooo. Erkannt wird diese auch meiner meinung nach richtig beim start. Habe hier mal die message :
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
hcd.c: ehci-hcd @ 00:1d.7, Intel Corp. 82801DB USB EHCI Controller
hcd.c: irq 3, pci mem e0848000
usb.c: new USB bus registered, assigned bus number 1
ehci-hcd.c: restricting 64bit DMA mappings to segment 0 ...
ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0
hub.c: USB hub found
hub.c: 6 ports detected
usb-uhci.c: $Revision: 1.275 $ time 05:47:42 Dec 12 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 4
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
hub.c: USB new device connect on bus4/1, assigned device number 2
usb-uhci.c: interrupt, status 3, frame# 552
hiddev0: USB HID v1.00 Gamepad [Microsoft SideWinder Game Voice] on usb4:2.0
hub.c: USB new device connect on bus4/2, assigned device number 3
usb.c: USB device 3 (vend/prod 0x3f0/0x3002) is not claimed by any active driver.
hub.c: USB new device connect on bus2/1, assigned device number 2
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: USB new device connect on bus2/2, assigned device number 3
usb-uhci.c: interrupt, status 3, frame# 258
input0: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse® 1.0A] on usb2:3.0
hub.c: USB new device connect on bus2/1/1, assigned device number 4
input1: USB HID v1.00 Joystick [Microsoft Microsoft SideWinder Precision Pro (USB)] on usb2:4.0
hub.c: USB new device connect on bus2/1/2, assigned device number 5
usb.c: USB device 5 (vend/prod 0x733/0x401) is not claimed by any active driver.
hub.c: USB new device connect on bus2/1/3, assigned device number 6
usb.c: registered new driver usblp
printer.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 1 proto 2 vid 0x03F0 pid 0x3002
Aber irgendwie funktioniert die nicht. Kann in der XF86Config auswählen was ich will bei dem Device. Aber nix regt sich :( Hat jemand einen Rat für mich??