realtec
23.09.02, 17:44
Hallo, ich möchte bei meiner Suse Firewall2 die Ports für edonkey an Windows Clients weiterleiten. Meine Konfig sieht u.A. so aus:
#
# 5.)
# Should routing between the internet, dmz and internal network be activated?
# REQUIRES: FW_DEV_INT or FW_DEV_DMZ
#
# You need only set this to yes, if you either want to masquerade internal
# machines or allow access to the dmz (or internal machines, but this is not
# a good idea). This option supersedes IP_FORWARD from
# /etc/sysconfig/network/options
#
# Setting this option one alone doesn't do anything. Either activate
# massquerading with FW_MASQUERADE below if you want to masquerade your
# internal network to the internet, or configure FW_FORWARD to define
# what is allowed to be forwarded!
#
# Choice: "yes" or "no", defaults to "no"
#
FW_ROUTE="yes"
#
# 6.)
# Do you want to masquerade internal networks to the outside?
# REQUIRES: FW_DEV_INT or FW_DEV_DMZ, FW_ROUTE
#
# "Masquerading" means that all your internal machines which use services on
# the internet seem to come from your firewall.
# Please note that it is more secure to communicate via proxies to the
# internet than masquerading. This option is required for FW_MASQ_NETS and
# FW_FORWARD_MASQ.
#
# Choice: "yes" or "no", defaults to "no"
#
FW_MASQUERADE="yes"
#
# You must also define on which interface(s) to masquerade on. This is
# normally your external device(s) to the internet.
# Most users can leave the default below.
#
# e.g. "ippp0" or "$FW_DEV_EXT"
FW_MASQ_DEV="$FW_DEV_EXT"
#
# Which internal computers/networks are allowed to access the internet
# directly (not via proxys on the firewall)?
# Only these networks will be allowed access and will be masqueraded!
#
# Choice: leave empty or any number of hosts/networks seperated by a space.
# Every host/network may get a list of allowed services, otherwise everything
# is allowed. A target network, protocol and service is appended by a comma to
# the host/network. e.g. "10.0.0.0/8" allows the whole 10.0.0.0 network with
# unrestricted access. "10.0.1.0/24,0/0,tcp,80 10.0.1.0/24,0/0tcp,21" allows
# the 10.0.1.0 network to use www/ftp to the internet.
# "10.0.1.0/24,tcp,1024:65535 10.0.2.0/24" is OK too.
# Set this variable to "0/0" to allow unrestricted access to the internet.
#
FW_MASQ_NETS="0/0"
#
# 7.)
# Do you want to protect the firewall from the internal network?
# REQUIRES: FW_DEV_INT
#
# If you set this to "yes", internal machines may only access services on
# the machine you explicitly allow. They will be also affected from the
# FW_AUTOPROTECT_SERVICES option.
# If you set this to "no", any user can connect (and attack) any service on
# the firewall.
#
# Choice: "yes" or "no", defaults to "yes"
#
# "yes" is a good choice
FW_PROTECT_FROM_INTERNAL="no"
#
# 8.)
# Do you want to autoprotect all running network services on the firewall?
#
# If set to "yes", all network access to services TCP and UDP on this machine
# will be prevented (except to those which you explicitly allow, see below:
# FW_SERVICES_{EXT,DMZ,INT}_{TCP,UDP})
#
# Choice: "yes" or "no", defaults to "yes"
#
FW_AUTOPROTECT_SERVICES="yes"
#
# 9.)
# Which services ON THE FIREWALL should be accessible from either the internet
# (or other untrusted networks), the dmz or internal (trusted networks)?
# (see no.13 & 14 if you want to route traffic through the firewall) XXX
#
# Enter all ports or known portnames below, seperated by a space.
# TCP services (e.g. SMTP, WWW) must be set in FW_SERVICES_*_TCP, and
# UDP services (e.g. syslog) must be set in FW_SERVICES_*_UDP.
# e.g. if a webserver on the firewall should be accessible from the internet:
# FW_SERVICES_EXT_TCP="www"
# e.g. if the firewall should receive syslog messages from the dmz:
# FW_SERVICES_DMZ_UDP="syslog"
# For IP protocols (like GRE for PPTP, or OSPF for routing) you need to set
# FW_SERVICES_*_IP with the protocol name or number (see /etc/protocols)
#
# Choice: leave empty or any number of ports, known portnames (from
# /etc/services) and port ranges seperated by a space. Port ranges are
# written like this: allow port 1 to 10 -> "1:10"
# e.g. "", "smtp", "123 514", "3200:3299", "ftp 22 telnet 512:514"
# For FW_SERVICES_*_IP enter the protocol name (like "igmp") or number ("2")
#
# Common: smtp domain
FW_SERVICES_EXT_TCP="4661 4662 4663 4664 4665 http https imap imaps pop3 pop3s smtp ssh"
# Common: domain
FW_SERVICES_EXT_UDP=""
# Common: domain
# For VPN/Routing which END at the firewall!!
FW_SERVICES_EXT_IP=""
#
# Common: smtp domain
FW_SERVICES_DMZ_TCP=""
# Common: domain
FW_SERVICES_DMZ_UDP=""
# For VPN/Routing which END at the firewall!!
FW_SERVICES_DMZ_IP=""
#
# Common: ssh smtp domain
FW_SERVICES_INT_TCP=""
# Common: domain syslog
FW_SERVICES_INT_UDP=""
# For VPN/Routing which END at the firewall!!
FW_SERVICES_INT_IP=""
#
# 10.)
# Which services should be accessible from trusted hosts/nets?
#
# Define trusted hosts/networks (doesnt matter if they are internal or
# external) and the TCP and/or UDP services they are allowed to use.
# Please note that a trusted host/net is *not* allowed to ping the firewall
# until you set it to allow also icmp!
#
# Choice: leave FW_TRUSTED_NETS empty or any number of computers and/or
# networks, seperated by a space. e.g. "172.20.1.1 172.20.0.0/16"
# Optional, enter a protocol after a comma, e.g. "1.1.1.1,icmp"
# Optional, enter a port after a protocol, e.g. "2.2.2.2,tcp,22"
#
FW_TRUSTED_NETS=""
#
# 11.)
# How is access allowed to high (unpriviliged [above 1023]) ports?
#
# You may either allow everyone from anyport access to your highports ("yes"),
# disallow anyone ("no"), anyone who comes from a defined port (portnumber or
# known portname) [note that this is easy to circumvent!], or just your
# defined nameservers ("DNS").
# Note that you can't use rpc requests (e.g. rpcinfo, showmount) as root
# from a firewall using this script (well, you can if you include range
# 600:1023 in FW_SERVICES_EXT_UDP ...).
# Please note that with v2.1 "yes" is not mandatory for active FTP from
# the firewall anymore.
#
# Choice: "yes", "no", "DNS", portnumber or known portname, defaults to "no"
# if not set
#
# Common: "ftp-data", better is "yes" to be sure that everything else works :-(
FW_ALLOW_INCOMING_HIGHPORTS_TCP="no"
# Common: "DNS" or "domain ntp", better is "yes" to be sure ...
FW_ALLOW_INCOMING_HIGHPORTS_UDP="DNS"
#
# 12.)
# Are you running some of the services below?
# They need special attention - otherwise they won´t work!
#
# Set services you are running to "yes", all others to "no", defaults to "no"
# if not set.
#
FW_SERVICE_AUTODETECT="yes"
# Autodetect the services below when starting
#
# If you are running bind/named set to yes. Remember that you have to open
# port 53 (or "domain") as udp/tcp to allow incoming queries.
# Also FW_ALLOW_INCOMING_HIGHPORTS_UDP needs to be "yes"
FW_SERVICE_DNS="no"
#
# if you use dhclient to get an ip address you have to set this to "yes" !
FW_SERVICE_DHCLIENT="no"
#
# set to "yes" if this server is a DHCP server
FW_SERVICE_DHCPD="no"
#
# set to "yes" if this server is running squid. You still have to open the
# tcp port 3128 to allow remote access to the squid proxy service.
FW_SERVICE_SQUID="no"
#
# set to "yes" if this server is running a samba server. You still have to open
# the tcp port 139 to allow remote access to SAMBA.
FW_SERVICE_SAMBA="no"
#
# 13.)
# Which services accessed from the internet should be allowed to the
# dmz (or internal network - if it is not masqueraded)?
# REQUIRES: FW_ROUTE
#
# With this option you may allow access to e.g. your mailserver. The
# machines must have valid, non-private, IP addresses which were assigned to
# you by your ISP. This opens a direct link to your network, so only use
# this option for access to your dmz!!!!
#
# Choice: leave empty (good choice!) or use the following explained syntax
# of forwarding rules, seperated each by a space.
# A forwarding rule consists of 1) source IP/net and 2) destination IP
# seperated by a comma. e.g. "1.1.1.1,2.2.2.2 3.3.3.3/16,4.4.4.4/24"
# Optional is a protocol, seperated by a comma, e.g. "5.5.5.5,6.6.6.6,igmp"
# Optional is a port after the protocol with a comma, e.g. "0/0,0/0,udp,514"
#
FW_FORWARD=""
# Beware to use this!
#
# 14.)
# Which services accessed from the internet should be allowed to masqueraded
# servers (on the internal network or dmz)?
# REQUIRES: FW_ROUTE
#
# With this option you may allow access to e.g. your mailserver. The
# machines must be in a masqueraded segment and may not have public IP addesses!
# Hint: if FW_DEV_MASQ is set to the external interface you have to set
# FW_FORWARD from internal to DMZ for the service as well to allow access
# from internal!
#
# Please note that this should *not* be used for security reasons! You are
# opening a hole to your precious internal network. If e.g. the webserver there
# is compromised - your full internal network is compromised!!
#
# Choice: leave empty (good choice!) or use the following explained syntax
# of forward masquerade rules, seperated each by a space.
# A forward masquerade rule consists of 1) source IP/net, 2) destination IP
# (dmz/intern), 3) a protocol (tcp/udp only!) and 4) destination port,
# seperated by a comma (","), e.g. "4.0.0.0/8,1.1.1.1,tcp,80"
# Optional is a port after the destination port, to redirect the request to
# a different destination port on the destination IP, e.g.
# "4.0.0.0/8,1.1.1.1,tcp,80,81"
#
# Freigaben für EDonkey, alle Rechner im Netz
FW_FORWARD_MASQ="0.0/0,192.168.x.x,tcp,4661:4662 0.0/0,192.168.x.x,udp,4665"
# FW_FORWARD_MASQ=""
# Beware to use this!
Wo aber liegt der Fehler, die Port sind auf Linux offen, werden aber nicht an die Windows Kisten weitergegeben???
#
# 5.)
# Should routing between the internet, dmz and internal network be activated?
# REQUIRES: FW_DEV_INT or FW_DEV_DMZ
#
# You need only set this to yes, if you either want to masquerade internal
# machines or allow access to the dmz (or internal machines, but this is not
# a good idea). This option supersedes IP_FORWARD from
# /etc/sysconfig/network/options
#
# Setting this option one alone doesn't do anything. Either activate
# massquerading with FW_MASQUERADE below if you want to masquerade your
# internal network to the internet, or configure FW_FORWARD to define
# what is allowed to be forwarded!
#
# Choice: "yes" or "no", defaults to "no"
#
FW_ROUTE="yes"
#
# 6.)
# Do you want to masquerade internal networks to the outside?
# REQUIRES: FW_DEV_INT or FW_DEV_DMZ, FW_ROUTE
#
# "Masquerading" means that all your internal machines which use services on
# the internet seem to come from your firewall.
# Please note that it is more secure to communicate via proxies to the
# internet than masquerading. This option is required for FW_MASQ_NETS and
# FW_FORWARD_MASQ.
#
# Choice: "yes" or "no", defaults to "no"
#
FW_MASQUERADE="yes"
#
# You must also define on which interface(s) to masquerade on. This is
# normally your external device(s) to the internet.
# Most users can leave the default below.
#
# e.g. "ippp0" or "$FW_DEV_EXT"
FW_MASQ_DEV="$FW_DEV_EXT"
#
# Which internal computers/networks are allowed to access the internet
# directly (not via proxys on the firewall)?
# Only these networks will be allowed access and will be masqueraded!
#
# Choice: leave empty or any number of hosts/networks seperated by a space.
# Every host/network may get a list of allowed services, otherwise everything
# is allowed. A target network, protocol and service is appended by a comma to
# the host/network. e.g. "10.0.0.0/8" allows the whole 10.0.0.0 network with
# unrestricted access. "10.0.1.0/24,0/0,tcp,80 10.0.1.0/24,0/0tcp,21" allows
# the 10.0.1.0 network to use www/ftp to the internet.
# "10.0.1.0/24,tcp,1024:65535 10.0.2.0/24" is OK too.
# Set this variable to "0/0" to allow unrestricted access to the internet.
#
FW_MASQ_NETS="0/0"
#
# 7.)
# Do you want to protect the firewall from the internal network?
# REQUIRES: FW_DEV_INT
#
# If you set this to "yes", internal machines may only access services on
# the machine you explicitly allow. They will be also affected from the
# FW_AUTOPROTECT_SERVICES option.
# If you set this to "no", any user can connect (and attack) any service on
# the firewall.
#
# Choice: "yes" or "no", defaults to "yes"
#
# "yes" is a good choice
FW_PROTECT_FROM_INTERNAL="no"
#
# 8.)
# Do you want to autoprotect all running network services on the firewall?
#
# If set to "yes", all network access to services TCP and UDP on this machine
# will be prevented (except to those which you explicitly allow, see below:
# FW_SERVICES_{EXT,DMZ,INT}_{TCP,UDP})
#
# Choice: "yes" or "no", defaults to "yes"
#
FW_AUTOPROTECT_SERVICES="yes"
#
# 9.)
# Which services ON THE FIREWALL should be accessible from either the internet
# (or other untrusted networks), the dmz or internal (trusted networks)?
# (see no.13 & 14 if you want to route traffic through the firewall) XXX
#
# Enter all ports or known portnames below, seperated by a space.
# TCP services (e.g. SMTP, WWW) must be set in FW_SERVICES_*_TCP, and
# UDP services (e.g. syslog) must be set in FW_SERVICES_*_UDP.
# e.g. if a webserver on the firewall should be accessible from the internet:
# FW_SERVICES_EXT_TCP="www"
# e.g. if the firewall should receive syslog messages from the dmz:
# FW_SERVICES_DMZ_UDP="syslog"
# For IP protocols (like GRE for PPTP, or OSPF for routing) you need to set
# FW_SERVICES_*_IP with the protocol name or number (see /etc/protocols)
#
# Choice: leave empty or any number of ports, known portnames (from
# /etc/services) and port ranges seperated by a space. Port ranges are
# written like this: allow port 1 to 10 -> "1:10"
# e.g. "", "smtp", "123 514", "3200:3299", "ftp 22 telnet 512:514"
# For FW_SERVICES_*_IP enter the protocol name (like "igmp") or number ("2")
#
# Common: smtp domain
FW_SERVICES_EXT_TCP="4661 4662 4663 4664 4665 http https imap imaps pop3 pop3s smtp ssh"
# Common: domain
FW_SERVICES_EXT_UDP=""
# Common: domain
# For VPN/Routing which END at the firewall!!
FW_SERVICES_EXT_IP=""
#
# Common: smtp domain
FW_SERVICES_DMZ_TCP=""
# Common: domain
FW_SERVICES_DMZ_UDP=""
# For VPN/Routing which END at the firewall!!
FW_SERVICES_DMZ_IP=""
#
# Common: ssh smtp domain
FW_SERVICES_INT_TCP=""
# Common: domain syslog
FW_SERVICES_INT_UDP=""
# For VPN/Routing which END at the firewall!!
FW_SERVICES_INT_IP=""
#
# 10.)
# Which services should be accessible from trusted hosts/nets?
#
# Define trusted hosts/networks (doesnt matter if they are internal or
# external) and the TCP and/or UDP services they are allowed to use.
# Please note that a trusted host/net is *not* allowed to ping the firewall
# until you set it to allow also icmp!
#
# Choice: leave FW_TRUSTED_NETS empty or any number of computers and/or
# networks, seperated by a space. e.g. "172.20.1.1 172.20.0.0/16"
# Optional, enter a protocol after a comma, e.g. "1.1.1.1,icmp"
# Optional, enter a port after a protocol, e.g. "2.2.2.2,tcp,22"
#
FW_TRUSTED_NETS=""
#
# 11.)
# How is access allowed to high (unpriviliged [above 1023]) ports?
#
# You may either allow everyone from anyport access to your highports ("yes"),
# disallow anyone ("no"), anyone who comes from a defined port (portnumber or
# known portname) [note that this is easy to circumvent!], or just your
# defined nameservers ("DNS").
# Note that you can't use rpc requests (e.g. rpcinfo, showmount) as root
# from a firewall using this script (well, you can if you include range
# 600:1023 in FW_SERVICES_EXT_UDP ...).
# Please note that with v2.1 "yes" is not mandatory for active FTP from
# the firewall anymore.
#
# Choice: "yes", "no", "DNS", portnumber or known portname, defaults to "no"
# if not set
#
# Common: "ftp-data", better is "yes" to be sure that everything else works :-(
FW_ALLOW_INCOMING_HIGHPORTS_TCP="no"
# Common: "DNS" or "domain ntp", better is "yes" to be sure ...
FW_ALLOW_INCOMING_HIGHPORTS_UDP="DNS"
#
# 12.)
# Are you running some of the services below?
# They need special attention - otherwise they won´t work!
#
# Set services you are running to "yes", all others to "no", defaults to "no"
# if not set.
#
FW_SERVICE_AUTODETECT="yes"
# Autodetect the services below when starting
#
# If you are running bind/named set to yes. Remember that you have to open
# port 53 (or "domain") as udp/tcp to allow incoming queries.
# Also FW_ALLOW_INCOMING_HIGHPORTS_UDP needs to be "yes"
FW_SERVICE_DNS="no"
#
# if you use dhclient to get an ip address you have to set this to "yes" !
FW_SERVICE_DHCLIENT="no"
#
# set to "yes" if this server is a DHCP server
FW_SERVICE_DHCPD="no"
#
# set to "yes" if this server is running squid. You still have to open the
# tcp port 3128 to allow remote access to the squid proxy service.
FW_SERVICE_SQUID="no"
#
# set to "yes" if this server is running a samba server. You still have to open
# the tcp port 139 to allow remote access to SAMBA.
FW_SERVICE_SAMBA="no"
#
# 13.)
# Which services accessed from the internet should be allowed to the
# dmz (or internal network - if it is not masqueraded)?
# REQUIRES: FW_ROUTE
#
# With this option you may allow access to e.g. your mailserver. The
# machines must have valid, non-private, IP addresses which were assigned to
# you by your ISP. This opens a direct link to your network, so only use
# this option for access to your dmz!!!!
#
# Choice: leave empty (good choice!) or use the following explained syntax
# of forwarding rules, seperated each by a space.
# A forwarding rule consists of 1) source IP/net and 2) destination IP
# seperated by a comma. e.g. "1.1.1.1,2.2.2.2 3.3.3.3/16,4.4.4.4/24"
# Optional is a protocol, seperated by a comma, e.g. "5.5.5.5,6.6.6.6,igmp"
# Optional is a port after the protocol with a comma, e.g. "0/0,0/0,udp,514"
#
FW_FORWARD=""
# Beware to use this!
#
# 14.)
# Which services accessed from the internet should be allowed to masqueraded
# servers (on the internal network or dmz)?
# REQUIRES: FW_ROUTE
#
# With this option you may allow access to e.g. your mailserver. The
# machines must be in a masqueraded segment and may not have public IP addesses!
# Hint: if FW_DEV_MASQ is set to the external interface you have to set
# FW_FORWARD from internal to DMZ for the service as well to allow access
# from internal!
#
# Please note that this should *not* be used for security reasons! You are
# opening a hole to your precious internal network. If e.g. the webserver there
# is compromised - your full internal network is compromised!!
#
# Choice: leave empty (good choice!) or use the following explained syntax
# of forward masquerade rules, seperated each by a space.
# A forward masquerade rule consists of 1) source IP/net, 2) destination IP
# (dmz/intern), 3) a protocol (tcp/udp only!) and 4) destination port,
# seperated by a comma (","), e.g. "4.0.0.0/8,1.1.1.1,tcp,80"
# Optional is a port after the destination port, to redirect the request to
# a different destination port on the destination IP, e.g.
# "4.0.0.0/8,1.1.1.1,tcp,80,81"
#
# Freigaben für EDonkey, alle Rechner im Netz
FW_FORWARD_MASQ="0.0/0,192.168.x.x,tcp,4661:4662 0.0/0,192.168.x.x,udp,4665"
# FW_FORWARD_MASQ=""
# Beware to use this!
Wo aber liegt der Fehler, die Port sind auf Linux offen, werden aber nicht an die Windows Kisten weitergegeben???