APIC error

[freaknoob]

wenn ich mein debian mit grafischer oberfläche starte kommt nach kurzer zeit folgende meldung in der konsole
[datum] debian kernel :[(hier eine vortlaufende zahl)] APIC error on CPU0 :80(80)
kann mir bitte jemand sagen was das bedeutet bzw was ich dagegen machen kann


mfg ich

[towo2099]

Und welche Hardware Du so benutzt sollen wir erraten?
Aber so ins Blaue geraten, boote halt mit noapic als Kernel-Parameter.

[freaknoob]

oh sry ich hab einen atom cpu und eine emintel grafik ... wenn man das so nennen kann :D


.... hmm scheint zu funktionieren (systemm läuft schon 1h ohne fehler)

[freaknoob]

danke dir .. ich hatte bis jetzt keine weiteren fehler :D

[freaknoob]

also ... seit heute funktioniert es schon wieder nich ... das system läauft 2 min un dann kommt gleich der apic error on cpu0: 80:80 .... plz help .. mein server muss funktionieren :D

[-hanky-]

Wie wäre es wenn du detailliert die Hardware angibst und die original Fehlermeldung hier in code-Tags postest (bzw. am Besten einfach gleich die komplette Ausgabe von dmesg, d.h. auch die Zeilen vor und nach Auftreten des Fehlers)?

Mit den dürftigen Informationen die du bislang gegeben hast kann man fast nur raten...

-hanky-

[freaknoob]

also erstmal dmesg

|more
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-25lenny1) (dannf@debian
.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Thu Sep
16 19:35:51 UTC 2010
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001fa50000 (usable)
[ 0.000000] BIOS-e820: 000000001fa50000 - 000000001fa60000 (reserved)
[ 0.000000] BIOS-e820: 000000001fa60000 - 000000001fa6e000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001fa6e000 - 000000001faaff90 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001faaff90 - 000000001fac0000 (reserved)
[ 0.000000] BIOS-e820: 000000001facc000 - 000000001fc00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 506MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00ff780] 000ff780
[ 0.000000] Entering add_active_range(0, 0, 129616) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 129616
[ 0.000000] HighMem 129616 -> 129616
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 129616
[ 0.000000] On node 0 totalpages: 129616
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 981 pages used for memmap
[ 0.000000] Normal zone: 124539 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F8FE0, 0024 (r2 ACPIAM)
[ 0.000000] ACPI: XSDT 1FA60100, 005C (r1 072009 XSDT1401 20090720 MSFT
97)
[ 0.000000] ACPI: FACP 1FA60290, 00F4 (r4 072009 FACP1401 20090720 MSFT
97)
[ 0.000000] ACPI: DSDT 1FA60430, 5C34 (r2 NOW1R NOW1R113 113 INTL 20051
117)
[ 0.000000] ACPI: FACS 1FA6E000, 0040
[ 0.000000] ACPI: APIC 1FA60390, 005C (r2 072009 APIC1401 20090720 MSFT
97)
[ 0.000000] ACPI: MCFG 1FA603F0, 003C (r1 072009 OEMMCFG 20090720 MSFT
97)
[ 0.000000] ACPI: OEMB 1FA6E040, 0131 (r1 072009 OEMB1401 20090720 MSFT
97)
[ 0.000000] ACPI: HPET 1FA66070, 0038 (r1 072009 OEMHPET 20090720 MSFT
97)
[ 0.000000] ACPI: GSCI 1FA6E180, 2024 (r1 072009 GMCHSCI 20090720 MSFT
97)
[ 0.000000] ACPI: SSDT 1FA70BB0, 04F0 (r1 PmRef CpuPm 3000 INTL 20051
117)
[ 0.000000] ACPI: PM-Timer IO Port: 0x908
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: Skipping IOAPIC probe due to 'noapic' option.
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI for processor (LAPIC) configuration information
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] Virtual Wire compatibility mode.
[ 0.000000] MPTABLE: OEM ID: KONTRON Product ID: Poulsbo <6>MPTABLE: Pr
oduct ID: Poulsbo <6>MPTABLE: APIC at: 0xFEE00000
[ 0.000000] I/O APIC #1 Version 32 at 0xFEC00000.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Processors: 2
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 1fc00000:df20
0000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37992 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 2
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 128603
[ 0.000000] Kernel command line: noapic root=/dev/hdb1 ro all_generic_ide qui
et
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Detected 1599.971 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Memory: 504004k/518464k available (1771k kernel code, 13884k rese
rved, 749k data, 244k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xdfa50000 ( 506 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02baebd - 0xc0376620 ( 749 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02baebd (1771 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor
mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.004000] hpet clockevent registered
[ 0.083983] Calibrating delay using timer specific routine.. 3202.98 BogoMIPS
(lpj=6405968)
[ 0.084005] Security Framework initialized
[ 0.084005] SELinux: Disabled at boot.
[ 0.084005] Capability LSM initialized
[ 0.084005] Mount-cache hash table entries: 512
[ 0.084005] Initializing cgroup subsys ns
[ 0.084005] Initializing cgroup subsys cpuacct
[ 0.084005] Initializing cgroup subsys devices
[ 0.084005] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 0.084005] CPU: L2 cache: 512K
[ 0.084005] CPU: Physical Processor ID: 0
[ 0.084005] Intel machine check architecture supported.
[ 0.084005] Intel machine check reporting enabled on CPU#0.
[ 0.084005] using mwait in idle threads.
[ 0.084005] Checking 'hlt' instruction... OK.
[ 0.100006] ACPI: Core revision 20080321
[ 0.112007] ACPI: setting ELCR to 0200 (from 8c20)
[ 0.116007] CPU0: Intel(R) Atom(TM) CPU Z530 @ 1.60GHz stepping 02
[ 0.116007] Booting processor 1/1 ip 6000
[ 0.124007] Initializing CPU#1
[ 0.124007] Calibrating delay using timer specific routine.. 3199.81 BogoMIPS
(lpj=6399626)
[ 0.124007] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 0.124007] CPU: L2 cache: 512K
[ 0.124007] CPU: Physical Processor ID: 0
[ 0.124007] Intel machine check architecture supported.
[ 0.124007] Intel machine check reporting enabled on CPU#1.
[ 0.204004] CPU1: Intel(R) Atom(TM) CPU Z530 @ 1.60GHz stepping 02
[ 0.204012] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.208013] Brought up 2 CPUs
[ 0.208013] Total of 2 processors activated (6402.79 BogoMIPS).
[ 0.208013] CPU0 attaching sched-domain:
[ 0.208013] domain 0: span 0-1
[ 0.208013] groups: 0 1
[ 0.208013] domain 1: span 0-1
[ 0.208013] groups: 0-1
[ 0.208013] CPU1 attaching sched-domain:
[ 0.208013] domain 0: span 0-1
[ 0.208013] groups: 1 0
[ 0.208013] domain 1: span 0-1
[ 0.208013] groups: 0-1
[ 0.124007] net_namespace: 660 bytes
[ 0.124007] Booting paravirtualized kernel on bare hardware
[ 0.124007] NET: Registered protocol family 16
[ 0.124007] ACPI: bus type pci registered
[ 0.124007] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.124007] PCI: Not using MMCONFIG.
[ 0.124007] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=3
[ 0.124007] PCI: Using configuration type 1 for base access
[ 0.124007] Setting up standard PCI resources
[ 0.218881] ACPI: EC: Look up EC in DSDT
[ 0.231520] ACPI: Interpreter enabled
[ 0.231529] ACPI: (supports S0 S1 S3 S5)
[ 0.231564] ACPI: Using PIC for interrupt routing
[ 0.231690] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.239950] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[ 0.239957] PCI: Using MMCONFIG for extended config space
[ 0.253836] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.254805] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.255228] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.POP4._PRT]
[ 0.255468] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.POP5._PRT]
[ 0.269837] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.269837] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.269837] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.269837] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[ 0.269837] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *
0, disabled.
[ 0.269837] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *
0, disabled.
[ 0.270125] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *
0, disabled.
[ 0.271984] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *
0, disabled.
[ 0.274536] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.274907] pnp: PnP ACPI init
[ 0.274927] ACPI: bus type pnp registered
[ 0.281439] pnp: PnP ACPI: found 13 devices
[ 0.281446] ACPI: ACPI bus type pnp unregistered
[ 0.281454] PnPBIOS: Disabled by ACPI PNP
[ 0.283417] PCI: Using ACPI for IRQ routing
[ 0.289191] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.289202] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.290295] ACPI: RTC can wake from S4
[ 0.297198] system 00:01: iomem range 0x20000000-0x7fffffff has been reserved
[ 0.297205] system 00:01: iomem range 0x1fc00000-0x1fffffff has been reserved
[ 0.297220] system 00:05: ioport range 0xa00-0xa8f has been reserved
[ 0.297233] system 00:06: ioport range 0x4d0-0x4d1 has been reserved
[ 0.297238] system 00:06: ioport range 0x900-0x9f3 has been reserved
[ 0.297244] system 00:06: ioport range 0x400-0x43f has been reserved
[ 0.297250] system 00:06: ioport range 0x480-0x4bf has been reserved
[ 0.297256] system 00:06: iomem range 0xf0000000-0xf0003fff has been reserved
[ 0.297277] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.297283] system 00:0a: iomem range 0xfee00000-0xfee00fff could not be rese
rved
[ 0.297296] system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.297308] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 0.297314] system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
[ 0.297320] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
[ 0.297326] system 00:0c: iomem range 0x100000-0x1fbfffff could not be reserv
ed
[ 0.328513] PCI: Bridge: 0000:00:1c.0
[ 0.328513] IO window: c000-cfff
[ 0.328513] MEM window: 0xbf500000-0xbfcfffff
[ 0.328513] PREFETCH window: 0x00000000fcb00000-0x00000000feafffff
[ 0.328513] PCI: Bridge: 0000:00:1c.1
[ 0.328513] IO window: d000-dfff
[ 0.328513] MEM window: 0xbfd00000-0xbfdfffff
[ 0.328513] PREFETCH window: disabled.
[ 0.328513] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
[ 0.328513] PCI: setting IRQ 10 as level-triggered
[ 0.328513] ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> GSI 10 (lev
el, low) -> IRQ 10
[ 0.328513] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.328513] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[ 0.328513] PCI: setting IRQ 11 as level-triggered
[ 0.328513] ACPI: PCI Interrupt 0000:00:1c.1[B] -> Link [LNKB] -> GSI 11 (lev
el, low) -> IRQ 11
[ 0.328513] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.328513] NET: Registered protocol family 2
[ 0.340656] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.344506] TCP established hash table entries: 16384 (order: 5, 131072 bytes
)
[ 0.344621] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.344731] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.344737] TCP reno registered
[ 0.352072] NET: Registered protocol family 1
[ 0.352506] checking if image is initramfs...<7>Switched to high resolution m
ode on CPU 1
[ 0.512154] Switched to high resolution mode on CPU 0
[ 0.708142] it is
[ 1.108977] Freeing initrd memory: 6077k freed
[ 1.112961] audit: initializing netlink socket (disabled)
[ 1.112961] type=2000 audit(1286785300.100:1): initialized
[ 1.112961] Total HugeTLB memory allocated, 0
[ 1.112961] VFS: Disk quotas dquot_6.5.1
[ 1.112961] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.112961] msgmni has been set to 996
[ 1.112961] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2
53)
[ 1.112961] io scheduler noop registered
[ 1.112961] io scheduler anticipatory registered
[ 1.112961] io scheduler deadline registered
[ 1.112961] io scheduler cfq registered (default)
[ 1.113000] pci 0000:00:02.0: Boot video device
[ 1.116958] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 1.116958] Allocate Port Service[0000:00:1c.0:pcie00]
[ 1.116958] Allocate Port Service[0000:00:1c.0:pcie02]
[ 1.116958] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 1.116958] Allocate Port Service[0000:00:1c.1:pcie00]
[ 1.116958] Allocate Port Service[0000:00:1c.1:pcie02]
[ 1.116958] isapnp: Scanning for PnP cards...
[ 1.472382] isapnp: No Plug & Play device found
[ 1.480388] hpet_resources: 0xfed00000 is busy
[ 1.480388] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
enabled
[ 1.484748] brd: module loaded
[ 1.484748] PNP: No PS/2 controller found. Probing ports directly.
[ 1.484748] i8042.c: No controller found.
[ 1.484748] mice: PS/2 mouse device common for all mice
[ 1.484748] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 1.484748] rtc0: alarms up to one month, y3k
[ 1.484748] cpuidle: using governor ladder
[ 1.484748] cpuidle: using governor menu
[ 1.484748] No iBFT detected.
[ 1.485616] TCP cubic registered
[ 1.485616] NET: Registered protocol family 17
[ 1.485616] Using IPI No-Shortcut mode
[ 1.485616] registered taskstats version 1
[ 1.485616] rtc_cmos 00:02: setting system clock to 2010-10-11 08:21:41 UTC (
1286785301)
[ 1.485687] Freeing unused kernel memory: 244k freed
[ 1.620384] Uniform Multi-Platform E-IDE driver
[ 1.620384] ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
[ 1.620384] ide_generic: please use "probe_mask=0x3f" module parameter for pr
obing all legacy ISA IDE ports
[ 1.620384] Probing IDE interface ide0...
[ 1.908589] hda: 2GB NANDrive, ATA DISK drive
[ 2.188588] hdb: WDC WD10EARS-00Y5B1, ATA DISK drive
[ 2.248381] Probing IDE interface ide1...
[ 3.060344] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 3.060344] ide1 at 0x170-0x177,0x376 on irq 15
[ 3.144316] ACPI: SSDT 1FA70280, 023C (r1 PmRef Cpu0Ist 3000 INTL 20051
117)
[ 3.144316] ACPI: SSDT 1FA70550, 065D (r1 PmRef Cpu0Cst 3001 INTL 20051
117)
[ 3.144316] Monitor-Mwait will be used to enter C-1 state
[ 3.144316] Monitor-Mwait will be used to enter C-2 state
[ 3.144316] Monitor-Mwait will be used to enter C-3 state
[ 3.144316] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 3.144316] ACPI: ACPI0007:00 is registered as cooling_device0
[ 3.144818] ACPI: SSDT 1FA701B0, 00CC (r1 PmRef Cpu1Ist 3000 INTL 20051
117)
[ 3.147483] ACPI: SSDT 1FA704C0, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20051
117)
[ 3.147483] Marking TSC unstable due to: TSC halts in idle.
[ 3.150305] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 3.150305] ACPI: ACPI0007:01 is registered as cooling_device1
[ 3.152457] ACPI: Expecting a [Reference] package element, found type C
[ 3.152457] ACPI: Expecting a [Reference] package element, found type C
[ 3.152458] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 3.153588] ACPI: Thermal Zone [THRM] (39 C)
[ 3.624252] hda: max request size: 128KiB
[ 3.624261] hda: 4000752 sectors (2048 MB) w/1KiB Cache, CHS=3969/16/63
[ 3.624272] hda: cache flushes not supported
[ 3.624348] hda:
[ 3.629487] hdb: max request size: 512KiB
[ 3.641493] hdb: 1953525168 sectors (1000204 MB), CHS=65535/255/63
[ 3.657495] hdb: cache flushes supported
[ 3.657495] hdb: hdb1 hdb2 < hdb5 > hdb3
[ 4.148882] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
[ 4.148882] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[ 4.148882] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKB] -> GSI 11 (lev
el, low) -> IRQ 11
[ 4.148882] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 4.231156] usbcore: registered new interface driver usbfs
[ 4.231156] usbcore: registered new interface driver hub
[ 4.231156] usbcore: registered new device driver usb
[ 4.251862] USB Universal Host Controller Interface driver v3.0
[ 4.271866] No dock devices found.
[ 4.299861] eth0: (PCI Express:2.5GB/s:Width x1) 00:e0:4b:2a:28:e3
[ 4.299861] eth0: Intel(R) PRO/1000 Network Connection
[ 4.299861] eth0: MAC: 3, PHY: 8, PBA No: ffffff-0ff
[ 4.299861] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 10 (lev
el, low) -> IRQ 10
[ 4.299884] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 4.299894] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 4.300960] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus numbe
r 1
[ 4.300960] uhci_hcd 0000:00:1d.0: irq 10, io base 0x0000e480
[ 4.300960] usb usb1: configuration #1 chosen from 1 choice
[ 4.300960] hub 1-0:1.0: USB hub found
[ 4.300960] hub 1-0:1.0: 2 ports detected
[ 4.299862] SCSI subsystem initialized
[ 4.301264] sdhci: Secure Digital Host Controller Interface driver
[ 4.301272] sdhci: Copyright(c) Pierre Ossman
[ 4.332954] libata version 3.00 loaded.
[ 4.404840] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.404850] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 4.404858] usb usb1: Product: UHCI Host Controller
[ 4.404864] usb usb1: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 4.404871] usb usb1: SerialNumber: 0000:00:1d.0
[ 4.404974] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKB] -> GSI 11 (lev
el, low) -> IRQ 11
[ 4.404996] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 4.405005] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 4.405079] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus numbe
r 2
[ 4.405120] uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000e080
[ 4.405320] usb usb2: configuration #1 chosen from 1 choice
[ 4.405396] hub 2-0:1.0: USB hub found
[ 4.405418] hub 2-0:1.0: 2 ports detected
[ 4.512477] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.512485] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 4.512490] usb usb2: Product: UHCI Host Controller
[ 4.512494] usb usb2: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 4.512499] usb usb2: SerialNumber: 0000:00:1d.1
[ 4.512609] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
[ 4.512609] PCI: setting IRQ 5 as level-triggered
[ 4.512609] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 5 (leve
l, low) -> IRQ 5
[ 4.512609] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 4.512609] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 4.512609] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus numbe
r 3
[ 4.512609] uhci_hcd 0000:00:1d.2: irq 5, io base 0x0000ef00
[ 4.512609] usb usb3: configuration #1 chosen from 1 choice
[ 4.512609] hub 3-0:1.0: USB hub found
[ 4.512609] hub 3-0:1.0: 2 ports detected
[ 4.616647] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.616656] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 4.616662] usb usb3: Product: UHCI Host Controller
[ 4.616667] usb usb3: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 4.616672] usb usb3: SerialNumber: 0000:00:1d.2
[ 4.617529] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 15
[ 4.617536] PCI: setting IRQ 15 as level-triggered
[ 4.617543] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKD] -> GSI 15 (lev
el, low) -> IRQ 15
[ 4.617570] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 4.617579] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 4.617640] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus numbe
r 4
[ 4.621596] ehci_hcd 0000:00:1d.7: debug port 1
[ 4.621609] PCI: cache line size of 32 is not supported by device 0000:00:1d.
7
[ 4.621617] ehci_hcd 0000:00:1d.7: request interrupt 15 failed
[ 4.621733] ehci_hcd 0000:00:1d.7: USB bus 4 deregistered
[ 4.621903] ACPI: PCI interrupt for device 0000:00:1d.7 disabled
[ 4.621910] ehci_hcd 0000:00:1d.7: init 0000:00:1d.7 fail, -16
[ 4.622020] ehci_hcd: probe of 0000:00:1d.7 failed with error -16
[ 4.622020] sdhci: SDHCI controller found at 0000:00:1e.0 [8086:811c] (rev 7)
[ 4.622020] ACPI: PCI Interrupt 0000:00:1e.0[A] -> Link [LNKA] -> GSI 10 (lev
el, low) -> IRQ 10
[ 4.622020] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 4.622020] mmc0: SDHCI at 0xdff3b800 irq 10 DMA
[ 4.629770] pata_sch 0000:00:1f.1: version 0.2
[ 4.629822] PCI: Unable to reserve I/O region #1:8@1f0 for device 0000:00:1f.
1
[ 4.629829] pata_sch 0000:00:1f.1: failed to request/iomap BARs for port 0 (e
rrno=-16)
[ 4.629838] PCI: Unable to reserve I/O region #3:8@170 for device 0000:00:1f.
1
[ 4.629844] pata_sch 0000:00:1f.1: failed to request/iomap BARs for port 1 (e
rrno=-16)
[ 4.629850] pata_sch 0000:00:1f.1: no available native port
[ 4.704315] usb 1-2: new low speed USB device using uhci_hcd and address 2
[ 4.880704] usb 1-2: configuration #1 chosen from 1 choice
[ 4.884771] usb 1-2: New USB device found, idVendor=046d, idProduct=c501
[ 4.884781] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.884789] usb 1-2: Product: USB Receiver
[ 4.884794] usb 1-2: Manufacturer: Logitech
[ 5.124360] usb 3-2: new low speed USB device using uhci_hcd and address 2
[ 5.279085] Clocksource tsc unstable (delta = -312514830 ns)
[ 5.299031] usb 3-2: configuration #1 chosen from 1 choice
[ 5.304034] usb 3-2: New USB device found, idVendor=046d, idProduct=c315
[ 5.304044] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.304052] usb 3-2: Product: Logitech USB Keyboard
[ 5.304057] usb 3-2: Manufacturer: Logitech
[ 5.306783] usbcore: registered new interface driver hiddev
[ 5.328025] input: Logitech USB Receiver as /class/input/input0
[ 5.332547] input,hidraw0: USB HID v1.10 Mouse [Logitech USB Receiver] on usb
-0000:00:1d.0-2
[ 5.344101] input: Logitech Logitech USB Keyboard as /class/input/input1
[ 5.367946] input,hidraw1: USB HID v1.10 Keyboard [Logitech Logitech USB Keyb
oard] on usb-0000:00:1d.2-2
[ 5.367946] usbcore: registered new interface driver usbhid
[ 5.367946] usbhid: v2.6:USB HID core driver
[ 5.560268] PM: Starting manual resume from disk
[ 5.602513] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 5.602513] EXT3-fs: write access will be enabled during recovery.
[ 12.774782] kjournald starting. Commit interval 5 seconds
[ 12.776582] EXT3-fs: hdb1: orphan cleanup on readonly fs
[ 12.776582] ext3_orphan_cleanup: deleting unreferenced inode 1148318
[ 12.776582] EXT3-fs: hdb1: 1 orphan inode deleted
[ 12.776582] EXT3-fs: recovery complete.
[ 12.799183] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.082286] udevd version 125 started
[ 18.357333] ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKA] -> GSI 10 (lev
el, low) -> IRQ 10
[ 18.357333] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 18.370791] input: PC Speaker as /class/input/input2
[ 18.388399] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS.
..
[ 20.302472] input: Power Button (CM) as /class/input/input3
[ 20.356092] ACPI: Power Button (CM) [PWRB]
[ 20.415691] ACPI: device:05 is registered as cooling_device2
[ 20.415691] ACPI: device:06 is registered as cooling_device3
[ 20.415986] input: Video Bus as /class/input/input4
[ 20.464579] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 20.562608] ACPI: AC Adapter [ADP1] (on-line)
[ 22.294081] Adding 1172704k swap on /dev/hdb5. Priority:-1 extents:1 across:
1172704k
[ 23.489584] EXT3 FS on hdb1, internal journal
[ 23.835404] loop: module loaded
[ 26.944518] kjournald starting. Commit interval 5 seconds
[ 26.950561] EXT3 FS on hdb3, internal journal
[ 26.950561] EXT3-fs: mounted filesystem with ordered data mode.
[ 32.490538] NET: Registered protocol family 10
[ 32.490796] lo: Disabled Privacy Extensions
[ 32.490796] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 37.060360] APIC error on CPU0: 00(80)
[ 37.565387] APIC error on CPU0: 80(80)
[ 45.030098] APIC error on CPU0: 80(80)
[ 45.065365] APIC error on CPU0: 80(80)
[ 45.146359] APIC error on CPU0: 80(80)
[ 45.146359] APIC error on CPU0: 80(80)
[ 45.184154] APIC error on CPU0: 80(80)
[ 45.223733] APIC error on CPU0: 80(80)
[ 45.227018] APIC error on CPU0: 80(80)
[ 45.265070] APIC error on CPU0: 80(80)
[ 45.285161] APIC error on CPU0: 80(80)
[ 45.329080] APIC error on CPU0: 80(80)
[ 45.443942] APIC error on CPU0: 80(80)
[ 45.464969] APIC error on CPU0: 80(80)
[ 45.594607] APIC error on CPU0: 80(80)
[ 45.610868] APIC error on CPU0: 80(80)
[ 45.641255] APIC error on CPU0: 80(80)
[ 45.654840] APIC error on CPU0: 80(80)
[ 45.674812] APIC error on CPU0: 80(80)
[ 45.744032] APIC error on CPU0: 80(80)
[ 45.768211] APIC error on CPU0: 80(80)
[ 45.792218] APIC error on CPU0: 80(80)
[ 45.792218] APIC error on CPU0: 80(80)
[ 45.818068] APIC error on CPU0: 80(80)
[ 45.826117] APIC error on CPU0: 80(80)
[ 45.836059] APIC error on CPU0: 80(80)
[ 45.951176] APIC error on CPU0: 80(80)
[ 45.967001] APIC error on CPU0: 80(80)
[ 46.010702] APIC error on CPU0: 80(80)
[ 46.023242] APIC error on CPU0: 80(80)
[ 46.032488] APIC error on CPU0: 80(80)
[ 46.063121] APIC error on CPU0: 80(80)
[ 46.138991] APIC error on CPU0: 80(80)
[ 49.191837] APIC error on CPU0: 80(80)
[ 49.297774] APIC error on CPU0: 80(80)
[ 50.958728] APIC error on CPU0: 80(80)
[ 50.966843] APIC error on CPU0: 80(80)
[ 50.991428] APIC error on CPU0: 80(80)
[ 51.012149] APIC error on CPU0: 80(80)
[ 51.646800] RPC: Registered udp transport module.
[ 51.646800] RPC: Registered tcp transport module.
[ 51.904338] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 52.022641] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery d
irectory
[ 52.034110] NFSD: starting 90-second grace period
[ 52.119521] APIC error on CPU0: 80(80)
[ 52.207938] APIC error on CPU0: 80(80)
[ 52.266933] APIC error on CPU0: 80(80)
[ 52.273813] APIC error on CPU0: 80(80)
[ 52.345038] APIC error on CPU0: 80(80)
[ 52.393868] APIC error on CPU0: 80(80)
[ 52.414454] APIC error on CPU0

[ 64.995675] APIC error on CPU0: 80(80)
[ 65.121762] APIC error on CPU0: 80(80)
[ 65.700616] APIC error on CPU0: 80(80)
[ 65.708544] APIC error on CPU0: 80(80)
[ 65.738877] APIC error on CPU0: 80(80)
[ 67.561354] mtrr: type mismatch for 1ffa0000,10000 old: write-back new: write
-combining
[ 67.561445] mtrr: type mismatch for 1ff80000,20000 old: write-back new: write
-combining
[ 67.561522] mtrr: type mismatch for 1ff00000,80000 old: write-back new: write
-combining
[ 67.561597] mtrr: type mismatch for 1fe00000,100000 old: write-back new: writ
e-combining
[ 67.561671] mtrr: type mismatch for 1fc00000,200000 old: write-back new: writ
e-combining
[ 68.277418] APIC error on CPU0: 80(80)
[ 68.301550] APIC error on CPU0: 80(80)
[ 68.545459] APIC error on CPU0: 80(80)
[ 68.557488] APIC error on CPU0: 80(80)
[ 68.563411] APIC error on CPU0: 80(80)
[ 68.569829] APIC error on CPU0: 80(80)

[ 105.199779] APIC error on CPU0: 80(80)
[ 105.209194] APIC error on CPU0: 80(80)
[ 105.238342] APIC error on CPU0: 80(80)
[ 105.259681] APIC error on CPU0: 80(80)
[ 105.275456] APIC error on CPU0: 80(80)
[ 105.291744] APIC error on CPU0: 80(80)
[ 105.293552] APIC error on CPU0: 80(80)
[ 105.304256] APIC error on CPU0: 80(80)
[ 105.309778] APIC error on CPU0: 80(80)
[ 105.311959] APIC error on CPU0: 80(80)
[ 105.327056] APIC error on CPU0: 80(80)
[ 105.336007] APIC error on CPU0: 80(80)

... usw (zwischendrinn hab ich n biss was weggelassen heißt bei dem apic error)


so jetzt zu hw cpu :

processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 28
model name : Intel(R) Atom(TM) CPU Z530 @ 1.60GHz
stepping : 2
cpu MHz : 800.000
cache size : 512 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
apicid : 0
initial apicid : 0
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx est tm2 ssse3 xtpr lahf_lm
bogomips : 3202.98
clflush size : 64
power management:

processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 28
model name : Intel(R) Atom(TM) CPU Z530 @ 1.60GHz
stepping : 2
cpu MHz : 800.000
cache size : 512 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
apicid : 1
initial apicid : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx est tm2 ssse3 xtpr lahf_lm
bogomips : 3199.81
clflush size : 64
power management:


graka weis ich grade nicht .. ist aber eine von intel ... wenn ich was finde poste ich das noch

[-hanky-]

Hi,

die Grafikkarte ist für das Problem denke ich nicht relevant, wird wohl eine onboard-Karte sein.

Könntest du aber noch die Ausgabe von lspci und "cat /proc/interrupts" hier posten?

-hanky-

[freaknoob]

also

lspci
00:00.0 Host bridge: Intel Corporation System Controller Hub (SCH Poulsbo) (rev 07)
00:02.0 VGA compatible controller: Intel Corporation System Controller Hub (SCH Poulsbo) Graphics Controller (rev 07)
00:1b.0 Audio device: Intel Corporation System Controller Hub (SCH Poulsbo) HD Audio Controller (rev 07)
00:1c.0 PCI bridge: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 1 (rev 07)
00:1c.1 PCI bridge: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 2 (rev 07)
00:1d.0 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #1 (rev 07)
00:1d.1 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #2 (rev 07)
00:1d.2 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #3 (rev 07)
00:1d.7 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB EHCI #1 (rev 07)
00:1e.0 SD Host controller: Intel Corporation System Controller Hub (SCH Poulsbo) SDIO Controller #1 (rev 07)
00:1f.0 ISA bridge: Intel Corporation System Controller Hub (SCH Poulsbo) LPC Bridge (rev 07)
00:1f.1 IDE interface: Intel Corporation System Controller Hub (SCH Poulsbo) IDE Controller (rev 07)
03:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection

und


cat /proc/interrupts
CPU0 CPU1
0: 10784 0 XT-PIC-XT timer
2: 0 0 XT-PIC-XT cascade
5: 37 0 XT-PIC-XT uhci_hcd:usb3
8: 5 0 XT-PIC-XT rtc0
9: 6 0 XT-PIC-XT acpi
10: 172 0 XT-PIC-XT uhci_hcd:usb1, mmc0, HDA Intel
11: 0 0 XT-PIC-XT uhci_hcd:usb2
14: 153365 0 XT-PIC-XT ide0
15: 1 0 XT-PIC-XT ide1
221: 3 0 PCI-MSI-edge eth0
222: 171 0 PCI-MSI-edge eth0-tx0
223: 199 0 PCI-MSI-edge eth0-rx0
NMI: 0 0 Non-maskable interrupts
LOC: 6190 9098 Local timer interrupts
RES: 2033 3067 Rescheduling interrupts
CAL: 78 143 function call interrupts
TLB: 34 37 TLB shootdowns
TRM: 0 0 Thermal event interrupts
SPU: 0 0 Spurious interrupts
ERR: 49
MIS: 0


und ja die graka is onboard

also .. ich hatte ja am anfang noch keine grafische oberfläche installiert ... und da ging es (ohne den fehler) ....

jetzt hab ich mal die grafische oberfläche wieder deinstalliert und es scheint zu funktionieren ... aber da ich einen vnc server darauf machen möchte brauche ich die grafische oberfläche sonnst würde ich die weglassen(das hier nur zur information)

[-hanky-]

Hm, so spontan fällt mir da jetzt auch kein Ansatz ein... hast du mal probeweise eine andere Distribution ausprobiert? Dein Board samt Chipsatz sowie die CPU sind ja relativ neu, der Kernel der verwendet wird hingegen schon ziemlich alt. Vielleicht wurde das Problem ja in einer neueren Kernelversion behoben?

-hanky-

[freaknoob]

ja genau .. das hat vorhin n kumpel von mir auch gemeint und er vermutet das es ein problem des grafikteibers ist ... hmm gibts schon einen neueren stabel kernel ??

[-hanky-]

Hab mal kurz recherchiert, dein Kumpel hat recht, es liegt wohl doch am Grafiktreiber. Siehe auch [1] und [2].

Der neueste stabile Kernel ist 2.6.35.7, ich habe aber keine Ahnung wie die Unterstützung des GMA500 (das ist die verwendete Grafik auf deinem Board) sich entwickelt hat, kann mir gut vorstellen dass viele Distributoren ihre Kernel mit extra Treibern diesbezüglich ausgestattet haben. Generell ist die Unterstützung des GMA500 wohl nicht gerade sonderlich ausgereift...

Wie gesagt, am Besten mal ein paar Distributionen mit halbwegs aktuellem Kernel ausprobieren.

-hanky-

[1] http://en.wikipedia.org/wiki/System_Controller_Hub
[2] https://wiki.ubuntu.com/HardwareSupportComponentsVideoCardsPoulsbo/

[freaknoob]

jop mach ich ...erstmal vielen dank für deine hilfe

[freaknoob]

also ich hab bis jetzt nur die linux-image-2.6.26 stable gefunden ... und ich wollte mir jetzt nicht extra nen neuen kernel komilieren deswegen ne linux image... ich hab mir volgende imgae ausgesucht ..http://packages.debian.org/squeeze/i386/linux-image-2.6.32-5-686/download aber den kann ich leider nicht installieren.. fehler kann ich grade nicht sagen ... aber poste den so schnell wie möglich

[-hanky-]

Das Kernelpaket ist aber aus "Squeeze", dem Testing-Zweig von Debian. Vermutlich wird die Installation daher an irgendwelchen nicht erfüllten Abhängigkeiten scheitern. Um die aufzulösen müsstest du entweder auf Testing wechseln oder versuchsweise nur die Pakete upgraden, von denen die Installation abhängt - wovon ich aber abrate, das gibt nur Wirrwarr, zumal im Extremfall jedes Paket dann selbst auch noch weitere Abhängigkeiten hat...

-hanky-

[freaknoob]

ja genau das problem ist aufgetreten ... habe dann das gesammte system auf testing geupdatet und dann ging es