fw114
01.06.10, 14:16
Hallo zusammen,
@ mods sollte der post hier nicht richtig sein bitte moved ! danke !
nach nun 7 tagen des bauens un probierens hat es avant fax nun geschafft, dass ich mich in einem forum anmelde...
zur sache:
hylafax läuft soweit und ich kann faxe emfpangen.. allerdings werden die faxe nicht von avantfax weiterverarbeitet. sie bleiben also schlicht in der queue liegen.
der fax empfang sieht so aus:
Jun 1 15:00:19 samba3 FaxGetty[24388]: --> [4:RING]
Jun 1 15:00:22 samba3 FaxGetty[24388]: --> [4:RING]
Jun 1 15:00:23 samba3 FaxGetty[24388]: --> [4:RING]
Jun 1 15:00:23 samba3 FaxGetty[24388]: DynamicConfig: bin/dynconf.php "/dev/ttyS0"
Jun 1 15:00:37 samba3 FaxGetty[24388]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Jun 1 15:01:07 samba3 FaxGetty[24388]: RECV FAX (000000002): from +++, page 1 in 0:00:21, INF, 3.85 line/mm, 1-D MH, 9600 bit/s
Jun 1 15:01:07 samba3 FaxGetty[24388]: RECV FAX (000000002): recvq/fax000000002.tif from +++, route to <unspecified>, 1 pages in 0:00:30
Jun 1 15:01:07 samba3 FaxGetty[24388]: RECV FAX: bin/faxrcvd.php "recvq/fax000000002.tif" "ttyS0" "000000002" ""
Jun 1 15:01:07 samba3 FaxGetty[24388]: <-- [5:ATH0\r]
Jun 1 15:01:12 samba3 FaxGetty[24388]: MODEM TIMEOUT: reading line from modem
Jun 1 15:01:12 samba3 FaxGetty[24388]: MODEM <Timeout>
Jun 1 15:01:12 samba3 FaxGetty[24388]: MODEM set DTR OFF
Jun 1 15:01:13 samba3 FaxGetty[24388]: MODEM set DTR OFF
Jun 1 15:01:13 samba3 FaxGetty[24388]: DELAY 75 ms
Jun 1 15:01:13 samba3 FaxGetty[24388]: MODEM set DTR ON
Jun 1 15:01:13 samba3 FaxGetty[24388]: DELAY 2600 ms
Jun 1 15:01:17 samba3 FaxGetty[24388]: MODEM set baud rate: 19200 baud, input flow RTS/CTS, output flow RTS/CTS
Jun 1 15:01:17 samba3 FaxGetty[24388]: DELAY 10 ms
Jun 1 15:01:17 samba3 FaxGetty[24388]: MODEM flush i/o
Jun 1 15:01:17 samba3 FaxGetty[24388]: <-- [4:ATZ\r]
Jun 1 15:01:17 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:17 samba3 FaxGetty[24388]: DELAY 3000 ms
Jun 1 15:01:20 samba3 FaxGetty[24388]: MODEM flush i/o
Jun 1 15:01:20 samba3 FaxGetty[24388]: <-- [7:ATS0=0\r]
Jun 1 15:01:20 samba3 FaxGetty[24388]: --> [6:ATS0=0]
Jun 1 15:01:20 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:20 samba3 FaxGetty[24388]: <-- [5:ATE0\r]
Jun 1 15:01:20 samba3 FaxGetty[24388]: --> [4:ATE0]
Jun 1 15:01:20 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:20 samba3 FaxGetty[24388]: <-- [5:ATV1\r]
Jun 1 15:01:20 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:20 samba3 FaxGetty[24388]: <-- [7:ATQ0X4\r]
Jun 1 15:01:20 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:20 samba3 FaxGetty[24388]: <-- [7:ATS8=2\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [8:ATS7=60\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [12:AT&H1&I0&R2\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [11:ATS13=1&D2\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [6:AT&C1\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [12:AT+FCLASS=?\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [7:0,1,2.0]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [14:AT+FCLASS=2.0\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [8:AT+FMI?\r]
Jun 1 15:01:22 samba3 FaxGetty[24388]: --> [21:U.S. Robotics 56K FAX]
Jun 1 15:01:22 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:22 samba3 FaxGetty[24388]: <-- [8:AT+FMM?\r]
Jun 1 15:01:22 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:22 samba3 FaxGetty[24388]: <-- [8:AT+FMR?\r]
Jun 1 15:01:22 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:22 samba3 FaxGetty[24388]: <-- [9:AT+FCC=?\r]
Jun 1 15:01:22 samba3 FaxGetty[24388]: --> [35:(0,1),(0-5),(0-2),(0-2),0,0,0,(0-7)]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:23 samba3 FaxGetty[24388]: <-- [9:AT+FSP=?\r]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [5:(0,1)]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:23 samba3 FaxGetty[24388]: <-- [9:AT+FLO=2\r]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:23 samba3 FaxGetty[24388]: <-- [9:AT+FPP=0\r]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:23 samba3 FaxGetty[24388]: <-- [9:AT+FBO=0\r]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:23 samba3 FaxGetty[24388]: <-- [10:AT+FCT=30\r]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:23 samba3 FaxGetty[24388]: <-- [15:AT+FNR=1,1,1,0\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [9:AT+FIE=0\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [9:AT+FBU=0\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: MODEM U.S. ROBOTICS 56K FAX /
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [5:ATM0\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [30:AT+FLI="Mein Fax "\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [9:AT+FCR=1\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [9:AT+FAA=1\r]
Jun 1 15:01:25 samba3 FaxGetty[24388]: --> [2:OK]
wobei ich sagen würde, das das proplem hier liegt:
route to <unspecified>
denn wenn ich manuell das fax an den
bin/faxrcvd.php mit
cd /var/spool/hylafax; for i in `ls recvq/*`; do bin/faxrcvd.php $i ttyS0; done
geht es und die faxe werden richtig verarbeitet und mail versand...
was also sehe ich nicht ?
wenn noch config files gewünscht werden, bitte kurzer hinweis, wollte jetzt nicht alles hier reinsetzten !
DANKE ! für jede hilfe oder hinweis
@ mods sollte der post hier nicht richtig sein bitte moved ! danke !
nach nun 7 tagen des bauens un probierens hat es avant fax nun geschafft, dass ich mich in einem forum anmelde...
zur sache:
hylafax läuft soweit und ich kann faxe emfpangen.. allerdings werden die faxe nicht von avantfax weiterverarbeitet. sie bleiben also schlicht in der queue liegen.
der fax empfang sieht so aus:
Jun 1 15:00:19 samba3 FaxGetty[24388]: --> [4:RING]
Jun 1 15:00:22 samba3 FaxGetty[24388]: --> [4:RING]
Jun 1 15:00:23 samba3 FaxGetty[24388]: --> [4:RING]
Jun 1 15:00:23 samba3 FaxGetty[24388]: DynamicConfig: bin/dynconf.php "/dev/ttyS0"
Jun 1 15:00:37 samba3 FaxGetty[24388]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Jun 1 15:01:07 samba3 FaxGetty[24388]: RECV FAX (000000002): from +++, page 1 in 0:00:21, INF, 3.85 line/mm, 1-D MH, 9600 bit/s
Jun 1 15:01:07 samba3 FaxGetty[24388]: RECV FAX (000000002): recvq/fax000000002.tif from +++, route to <unspecified>, 1 pages in 0:00:30
Jun 1 15:01:07 samba3 FaxGetty[24388]: RECV FAX: bin/faxrcvd.php "recvq/fax000000002.tif" "ttyS0" "000000002" ""
Jun 1 15:01:07 samba3 FaxGetty[24388]: <-- [5:ATH0\r]
Jun 1 15:01:12 samba3 FaxGetty[24388]: MODEM TIMEOUT: reading line from modem
Jun 1 15:01:12 samba3 FaxGetty[24388]: MODEM <Timeout>
Jun 1 15:01:12 samba3 FaxGetty[24388]: MODEM set DTR OFF
Jun 1 15:01:13 samba3 FaxGetty[24388]: MODEM set DTR OFF
Jun 1 15:01:13 samba3 FaxGetty[24388]: DELAY 75 ms
Jun 1 15:01:13 samba3 FaxGetty[24388]: MODEM set DTR ON
Jun 1 15:01:13 samba3 FaxGetty[24388]: DELAY 2600 ms
Jun 1 15:01:17 samba3 FaxGetty[24388]: MODEM set baud rate: 19200 baud, input flow RTS/CTS, output flow RTS/CTS
Jun 1 15:01:17 samba3 FaxGetty[24388]: DELAY 10 ms
Jun 1 15:01:17 samba3 FaxGetty[24388]: MODEM flush i/o
Jun 1 15:01:17 samba3 FaxGetty[24388]: <-- [4:ATZ\r]
Jun 1 15:01:17 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:17 samba3 FaxGetty[24388]: DELAY 3000 ms
Jun 1 15:01:20 samba3 FaxGetty[24388]: MODEM flush i/o
Jun 1 15:01:20 samba3 FaxGetty[24388]: <-- [7:ATS0=0\r]
Jun 1 15:01:20 samba3 FaxGetty[24388]: --> [6:ATS0=0]
Jun 1 15:01:20 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:20 samba3 FaxGetty[24388]: <-- [5:ATE0\r]
Jun 1 15:01:20 samba3 FaxGetty[24388]: --> [4:ATE0]
Jun 1 15:01:20 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:20 samba3 FaxGetty[24388]: <-- [5:ATV1\r]
Jun 1 15:01:20 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:20 samba3 FaxGetty[24388]: <-- [7:ATQ0X4\r]
Jun 1 15:01:20 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:20 samba3 FaxGetty[24388]: <-- [7:ATS8=2\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [8:ATS7=60\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [12:AT&H1&I0&R2\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [11:ATS13=1&D2\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [6:AT&C1\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [12:AT+FCLASS=?\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [7:0,1,2.0]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [14:AT+FCLASS=2.0\r]
Jun 1 15:01:21 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:21 samba3 FaxGetty[24388]: <-- [8:AT+FMI?\r]
Jun 1 15:01:22 samba3 FaxGetty[24388]: --> [21:U.S. Robotics 56K FAX]
Jun 1 15:01:22 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:22 samba3 FaxGetty[24388]: <-- [8:AT+FMM?\r]
Jun 1 15:01:22 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:22 samba3 FaxGetty[24388]: <-- [8:AT+FMR?\r]
Jun 1 15:01:22 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:22 samba3 FaxGetty[24388]: <-- [9:AT+FCC=?\r]
Jun 1 15:01:22 samba3 FaxGetty[24388]: --> [35:(0,1),(0-5),(0-2),(0-2),0,0,0,(0-7)]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:23 samba3 FaxGetty[24388]: <-- [9:AT+FSP=?\r]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [5:(0,1)]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:23 samba3 FaxGetty[24388]: <-- [9:AT+FLO=2\r]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:23 samba3 FaxGetty[24388]: <-- [9:AT+FPP=0\r]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:23 samba3 FaxGetty[24388]: <-- [9:AT+FBO=0\r]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:23 samba3 FaxGetty[24388]: <-- [10:AT+FCT=30\r]
Jun 1 15:01:23 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:23 samba3 FaxGetty[24388]: <-- [15:AT+FNR=1,1,1,0\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [9:AT+FIE=0\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [9:AT+FBU=0\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: MODEM U.S. ROBOTICS 56K FAX /
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [5:ATM0\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [30:AT+FLI="Mein Fax "\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [9:AT+FCR=1\r]
Jun 1 15:01:24 samba3 FaxGetty[24388]: --> [2:OK]
Jun 1 15:01:24 samba3 FaxGetty[24388]: <-- [9:AT+FAA=1\r]
Jun 1 15:01:25 samba3 FaxGetty[24388]: --> [2:OK]
wobei ich sagen würde, das das proplem hier liegt:
route to <unspecified>
denn wenn ich manuell das fax an den
bin/faxrcvd.php mit
cd /var/spool/hylafax; for i in `ls recvq/*`; do bin/faxrcvd.php $i ttyS0; done
geht es und die faxe werden richtig verarbeitet und mail versand...
was also sehe ich nicht ?
wenn noch config files gewünscht werden, bitte kurzer hinweis, wollte jetzt nicht alles hier reinsetzten !
DANKE ! für jede hilfe oder hinweis