PDA

Archiv verlassen und diese Seite im Standarddesign anzeigen : Suse10.3 + Fehler Zugriff auf Internet-Zugang



nomad
09.04.10, 13:35
hi,
ich bins wieder mal.

>> zuletzt im thema System installieren
Posting: Probleme bei Win7 + Suse11.2

da hatte ich mich zu frueh gefreut, mit dem Internet-zugang

hardware toshiba Rtl8111 , pci8168 pci express Gigabit Ethernet-controler
mit DHCP
Kernel modul r8169

einwahl mit knetworkmanager

zur zeit hab ich nicht einmal auf der taskleiste ein networkmanager symbol

in den letzten zwei tagen kam ich ab und zu ins web
zur zeit keinerlei zugang
gemaess meiner posting vom 27.03.2010

hab ich folgende versuch und tests gemacht:

1)


--> rcnetwork restart -o nm
Shutting down the NetworkManager done
Shutting down the DHCP DBUS Daemon done
Shutting down the NetworkManagerDispatcdone
Starting the DHCP DBUS Daemon done
Starting the NetworkManagerDispatcher done
Starting the NetworkManager done


vermutlich schon 1.fehler : DBUS
da letztes mal folgendes 27.03. -> selbes System mit



Shutting down the NetworkManager done
Shutting down network interfaces:
eth0 device: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
eth0 done
Shutting down service network . . . . . . . . . done
Starting the NetworkManager done
mycomputer:~/Desktop #


Frage: wie bekomm ich den DBUS raus ???


2)


linux-uctf:~ # ifconfig
eth0 Link encap:Ethernet HWaddr 00:23:18:59:AC:5A
inet addr:169.254.124.101 Bcast:169.254.255.255 Mask:255.255.0.0
inet6 addr: fe80::223:18ff:fe59:ac5a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:562640715645 overruns:0 frame:0
TX packets:0 errors:0 dropped:94 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:17

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1002 errors:0 dropped:0 overruns:0 frame:0
TX packets:1002 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:73212 (71.4 Kb) TX bytes:73212 (71.4 Kb)

linux-uctf:~ #


3) dann test mit collectNWData.sh



collectNWData.sh V0.6.3.4 (Rev: 1.220, Build: 2010/04/05 13:36:33 UTC)
--- Which type of your network connection should be tested?
--- (1) Wired connection
--- What's the type of networktopology?
--- (2) DSL HW router <---> LinuxClient
--- On which host is the script executed?
--- (1) LinuxClient

--- NWEliza is analyzing the system for common network configuration errors ...

!!! CND0210W: APIPA IP address 169.254.124.101 detected on network card eth0
!!! CND0180I: The system can't ping external IP address 195.135.220.3
!!! CND0140E: No default gateway set on your system
!!! CND0230W: IPV6 enabled
!!! CND0240E: knetworkmanager for network configuration enabled but a YAST network card configuration for eth0 exist

--- Go to http://www.linux-tips-and-tricks.de/CND#English to get more detailed instructions
--- about the error/warning messages and how to fix the problems on your own.

--- If you are unsuccessful then place the contents of file collectNWData.txt in the net
--- (see http://www.linux-tips-and-tricks.de/CND_UPL#English for links)
--- and then paste the nopaste link on your favorite Linux forum.

================================================== ================================================== ==============
================================================== ================================================== ==============
*** uname -a
Linux linux-uctf 2.6.22.5-31-default #1 SMP 2007/09/21 22:29:00 UTC x86_64 x86_64 x86_64 GNU/Linux
================================================== ================================================== ==============
*** cat /etc/*[-_]release || cat /etc/*[-_]version
/etc/SuSE-release
/etc/lsb-release
openSUSE 10.3 (X86-64)
VERSION = 10.3
LSB_VERSION="core-2.0-noarch:core-3.0-noarch:core-2.0-x86_64:core-3.0-x86_64"
================================================== ================================================== ==============
*** cat /etc/resolv | grep -i "nameserver"
================================================== ================================================== ==============
*** cat /etc/hosts
127.0.0.1 localhost
127.0.0.2 linux-uctf.site linux-uctf
================================================== ================================================== ==============
*** route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
================================================== ================================================== ==============
*** ifconfig
eth0 Link encap:Ethernet HWaddr ##:##:##:##:##:#1
inet addr:169.254.124.101 Bcast:169.254.255.255 Mask:255.255.0.0
inet6 addr: fe80::223:18ff:fe59:ac5a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:824633720640 overruns:0 frame:0
TX packets:0 errors:0 dropped:94 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:17
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1118 errors:0 dropped:0 overruns:0 frame:0
TX packets:1118 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:81500 (79.5 Kb) TX bytes:81500 (79.5 Kb)
================================================== ================================================== ==============
*** ping tests
connect: Network is unreachable
Ping of 195.135.220.3 failed
ping: unknown host www.suse.de
Ping of www.suse.de failed
================================================== ================================================== ==============
*** dhcpcd-test
eth0: No DHCP server detected dhcpcd: MAC address = ##:##:##:##:##:#1
================================================== ================================================== ==============
*** lspci
03:00.0 Network controller [Class 0280]: Realtek Semiconductor Co., Ltd. Unknown device [10ec:8172] (rev 10)
06:00.0 Ethernet controller [Class 0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03)
================================================== ================================================== ==============
*** lsusb
Bus 002 Device 002: ID 8087:0020
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 004: ID 04f2:b130 Chicony Electronics Co., Ltd
Bus 001 Device 003: ID 1164:0871 YUAN High-Tech Development Co., Ltd
Bus 001 Device 002: ID 8087:0020
Bus 001 Device 001: ID 0000:0000
================================================== ================================================== ==============
*** hwinfo (filtered)
29: PCI 300.0: 0280 Network controller
Model: "Realtek Network controller"
Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
Device: pci 0x8172
SubVendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
SubDevice: pci 0x8182
30: PCI 600.0: 0200 Ethernet controller
Model: "Toshiba America Info RTL8111/8168B PCI Express Gigabit Ethernet controller"
Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
Device: pci 0x8168 "RTL8111/8168B PCI Express Gigabit Ethernet controller"
SubVendor: pci 0x1179 "Toshiba America Info Systems"
SubDevice: pci 0x0002
Driver: "r8169"
Driver Modules: "r8169"
Device File: eth0
Link detected: yes
Driver Status: r8169 is active
Driver Activation Cmd: "modprobe r8169"
================================================== ================================================== ==============
*** lsmod # (filtered)
| ac | acpi_cpufreq | af_packet | ahci | apparmor |
| battery | compat_ioctl32 | cpufreq_conservative| cpufreq_powersave| cpufreq_userspace |
| edd | ehci_hcd | fat | firmware_class | ip6t_LOG |
| ip6t_REJECT | iptable_mangle | iptable_nat | jbd | libata |
| mbcache | microcode | mmc_core | nf_conntrack_ipv4| nf_nat |
| nfnetlink | nls_cp437 | nls_iso8859_1 | r8169 | scsi_mod |
| sd_mod | sdhci | sg | sr_mod | thermal |
| usb_storage | uvcvideo | v4l1_compat | v4l2_common | vfat |
| xt_limit | xt_pkttype | xt_state | xt_tcpudp |
================================================== ================================================== ==============
*** cat /etc/sysconfig/network/ifcfg-[earwd]*
--- /etc/sysconfig/network/ifcfg-eth0
BOOTPROTO='dhcp'
BROADCAST=''
ETHTOOL_OPTIONS=''
IFPLUGD_PRIORITY='20'
IPADDR=''
MTU=''
NAME='Toshiba America Info RTL8111/8168B PCI Express Gigabit Ethernet controller'
NETMASK=''
NETWORK=''
REMOTE_IPADDR=''
STARTMODE='ifplugd'
USERCONTROL='no'
================================================== ================================================== ==============
*** NWElizaStates
IF:eth0 IM:1 DI:1 NIC:0 cNiC:1:0 NI:0 cNI:0 PNG:1 DR:0 MTU:1 NISS:0 IP6:1 KM:1 WLW:0 RTDT:SuSE


hier die fehler-beschreibung von cnd
t


CND0210E APIPA IP ADRESSE WURDE AN NETZWERKKART %1 ENTDECKT
ip adress 169.254.124.101 detected

CND0180i DAS SYSTEM KANN KEINE EXTERNE IP PINGEN

CND0140E NO DEFAULT GATEWAY SET ON YOUR SYSTEM

CND0230W IPV6 ENABLED (erledigt)

CND0240E Knetworkmanager wird für die Netzwerkkonfiguration benutzt aber die Netzwerkkartenkonfiguration %1 existiert
CND0210E APIPA IP ADRESSE WURDE AN NETZWERKKART %1 ENTDECKT
ip adress 169.254.124.101 detected

CND0180i DAS SYSTEM KANN KEINE EXTERNE IP PINGEN
bespiel ping 195.135.220.3

CND0140E NO DEFAULT GATEWAY SET ON YOUR SYSTEM


CND0230W IPV6 ENABLED

CND0240E Knetworkmanager wird für die Netzwerkkonfiguration benutzt aber die Netzwerkkartenkonfiguration %1 existier


noch mehr fehler als letztes mal
die IPV6 ist jetzt draussen
auch bei FireFox

jetzt weiss ich ueberhaupt nicht mehr weiter

um hilfe waere ich sehr dankbar,
gruss nomad

stefan.becker
09.04.10, 16:31
Warum suchst du bei ollen Kamellen nach WLAN Fehlern? Installiere 11.2 und löse dort die Probleme, das macht wenigstens Sinn.

nomad
09.04.10, 16:55
hi,
wer spricht da ueber WLAN
Falls du den DBUS meinst den hab ich nirgends ausgewaehlt

iich hab nur die tests durch gefuehrt, welche mir am 27.03. vom forum vorgeschlagen
wurde.... wie michs mach, mach ichs falsch -> schoooench.

2. also ich finde 10.3. keine allten kammellen,
ich bin nicht ganz freiwillig zu 10.3. zurueckgekehrt
sondern, weil einige dutzend recht komplexe opencv und opengl progs
unter 11.2. nicht mehr gelaufen sind. Speicherzugriffs-fehler
und ich hab keine zeit und auch keine lust dazu die programme an 11.2.
anzupassen. das war ein mannjahr an arbeit
und durch einen wechsel wuerd ich mir noch mehr probleme einfangen
guck mal bei google -> ehci-project ;-)

es waere aber schoen, wenn ihr mir trotzdem helfen koenntet ???
auch wenn ich nicht das neueste OS benutze.
gruss
nomad