Henning14
12.11.09, 09:46
Hi Folks,
ich weiss nicht mehr weiter.
Ich bekomme unter Linux keine Connection mehr zum AP.
Unter WIN klappt es jedoch.
Ein anderer AP ist jedoch auch unter Linux gut erreichbar, es liegt also nicht grundsätzlich am Treiber oder sowas. ndiswrapper wird korrekt geladen, iwlist scan zeigt mir den AP korrekt an. Passwort ist korrekt .....
Vorher ging das jedoch
Den AP (Fritzbox FON) verwalte ich nicht selbst, kann die Einträge nicht überprüfen.
Die Debugausgabe von wpa_supplicant meint folgendes:
Die -meines Erachtens- wichtige Stelle male ich mal rot an:
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf.kocker' driver 'default' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf.kocker' -> '/etc/wpa_supplicant.conf.kocker'
Reading configuration file '/etc/wpa_supplicant.conf.kocker'
ctrl_interface='/var/run/wpa_supplicant'
Priority group 0
id=0 ssid='FRITZ!Box Fon WLAN 7113'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=18 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:0e:2e:f7:e7:51
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 240 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:24:fe:33:9f:38 ssid='FRITZ!Box Fon WLAN 7113' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
skip - no WPA/RSN IE
Try to find non-WPA AP
0: 00:24:fe:33:9f:38 ssid='FRITZ!Box Fon WLAN 7113' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Was heisst überhaupt " no WPA/RSN IE" ??
Ich poste auch mal die Ausgabe von iwlist scan:
wlan0 Scan completed :
Cell 01 - Address: 00:24:FE:33:9F:38
ESSID:"FRITZ!Box Fon WLAN 7113"
Protocol:IEEE 802.11g
Mode:Managed
Frequency:2.412 GHz (Channel 1)
Quality:59/100 Signal level:-58 dBm Noise level:-96 dBm
Encryption key:on
Bit Rate:1 Mb/s
Bit Rate:2 Mb/s
Bit Rate:5.5 Mb/s
Bit Rate:11 Mb/s
Bit Rate:6 Mb/s
Bit Rate:9 Mb/s
Bit Rate:12 Mb/s
Bit Rate:18 Mb/s
Bit Rate:24 Mb/s
Bit Rate:36 Mb/s
Bit Rate:48 Mb/s
Bit Rate:54 Mb/s
Extra:bcn_int=100
Extra:atim=0
Ich habe den richtigen Kanal, richtiges passwort, ich weiss einfach nicht mehr weiter... *heul* ;-)
Wie gesagt.... an einem anderen Access Point (auch WPA2) komme ich ohne weiteres ran .... muss wohl mal die Debugausgabe des erfolgreichen AP`s mit dem anderen vergleichen, fleischt werde isch dann schlauer *sfz*
Was ist ziemlich komisch finde: wpa_ie_len=0 rsn_ie_len=0
"Null" ist doch sehr wenig, oda????
Thx 4 any help
ich weiss nicht mehr weiter.
Ich bekomme unter Linux keine Connection mehr zum AP.
Unter WIN klappt es jedoch.
Ein anderer AP ist jedoch auch unter Linux gut erreichbar, es liegt also nicht grundsätzlich am Treiber oder sowas. ndiswrapper wird korrekt geladen, iwlist scan zeigt mir den AP korrekt an. Passwort ist korrekt .....
Vorher ging das jedoch
Den AP (Fritzbox FON) verwalte ich nicht selbst, kann die Einträge nicht überprüfen.
Die Debugausgabe von wpa_supplicant meint folgendes:
Die -meines Erachtens- wichtige Stelle male ich mal rot an:
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf.kocker' driver 'default' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf.kocker' -> '/etc/wpa_supplicant.conf.kocker'
Reading configuration file '/etc/wpa_supplicant.conf.kocker'
ctrl_interface='/var/run/wpa_supplicant'
Priority group 0
id=0 ssid='FRITZ!Box Fon WLAN 7113'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=18 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:0e:2e:f7:e7:51
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 240 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:24:fe:33:9f:38 ssid='FRITZ!Box Fon WLAN 7113' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
skip - no WPA/RSN IE
Try to find non-WPA AP
0: 00:24:fe:33:9f:38 ssid='FRITZ!Box Fon WLAN 7113' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Was heisst überhaupt " no WPA/RSN IE" ??
Ich poste auch mal die Ausgabe von iwlist scan:
wlan0 Scan completed :
Cell 01 - Address: 00:24:FE:33:9F:38
ESSID:"FRITZ!Box Fon WLAN 7113"
Protocol:IEEE 802.11g
Mode:Managed
Frequency:2.412 GHz (Channel 1)
Quality:59/100 Signal level:-58 dBm Noise level:-96 dBm
Encryption key:on
Bit Rate:1 Mb/s
Bit Rate:2 Mb/s
Bit Rate:5.5 Mb/s
Bit Rate:11 Mb/s
Bit Rate:6 Mb/s
Bit Rate:9 Mb/s
Bit Rate:12 Mb/s
Bit Rate:18 Mb/s
Bit Rate:24 Mb/s
Bit Rate:36 Mb/s
Bit Rate:48 Mb/s
Bit Rate:54 Mb/s
Extra:bcn_int=100
Extra:atim=0
Ich habe den richtigen Kanal, richtiges passwort, ich weiss einfach nicht mehr weiter... *heul* ;-)
Wie gesagt.... an einem anderen Access Point (auch WPA2) komme ich ohne weiteres ran .... muss wohl mal die Debugausgabe des erfolgreichen AP`s mit dem anderen vergleichen, fleischt werde isch dann schlauer *sfz*
Was ist ziemlich komisch finde: wpa_ie_len=0 rsn_ie_len=0
"Null" ist doch sehr wenig, oda????
Thx 4 any help