dexter0
30.09.09, 00:58
Hallo!
Ich versuche eine Bluetooth-Verbindung zwischen meinem Laptop und meinem neuen Motorola VE538 herzustellen. Ich lege also den Schalter für den Bluetooth-Adapter an meinem Laptop um, und bekomme folgende Ausgabe bei dmesg
[ 3578.392959] atkbd.c: Unknown key pressed (translated set 2, code 0xf1 on isa0060/serio0).
[ 3578.392959] atkbd.c: Use 'setkeycodes e071 <keycode>' to make it known.
[ 3578.400796] atkbd.c: Unknown key released (translated set 2, code 0xf1 on isa0060/serio0).
[ 3578.400796] atkbd.c: Use 'setkeycodes e071 <keycode>' to make it known.
[ 3578.994878] usb 2-1: new full speed USB device using uhci_hcd and address 3
[ 3579.150754] usb 2-1: configuration #1 chosen from 1 choice
[ 3579.153170] usb 2-1: New USB device found, idVendor=0a5c, idProduct=2101
[ 3579.153185] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3579.153191] usb 2-1: Product: Foxconn Bluetooth 2.0 plus EDR
[ 3579.153195] usb 2-1: Manufacturer: Broadcom Corp
[ 3579.220218] Bluetooth: HCI USB driver ver 2.9
[ 3579.221925] usbcore: registered new interface driver hci_usb
hciconfig -a
hci0: Type: USB
BD Address: 00:19:7D:E4:0E:C9 ACL MTU: 1017:8 SCO MTU: 64:8
UP RUNNING PSCAN
RX bytes:9282 acl:0 sco:0 events:313 errors:0
TX bytes:677 acl:0 sco:0 commands:99 errors:0
Features: 0xff 0xff 0x8f 0xfe 0x9b 0xf9 0x00 0x80
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH HOLD SNIFF PARK
Link mode: SLAVE ACCEPT
Name: 'Stefan-0'
Class: 0x4a010c
Service Classes: Networking, Capturing, Telephony
Device Class: Computer, Laptop
HCI Ver: 2.0 (0x3) HCI Rev: 0x213b LMP Ver: 2.0 (0x3) LMP Subver: 0x41d3
Manufacturer: Broadcom Corporation (15)
# /etc/init.d/bluetooth status
bluetooth is running.
Aber das Icon in der Notification Area erscheint nicht, wenn ich bei bluetooth-properties auswähle Nur zeigen, wenn ein Adapter vorhanden ist, obwohl der ja vorhanden ist. Mein Handy findet auch meinen Adapter nicht, wohl aber andere PCs.
# hcitool scan
Scanning ...
00:17:CA:5A:D8:F6 VE538
00:22:FD:3E:CA:C1 N95jags
# hcitool info 00:17:CA:5A:D8:F6
Requesting information ...
BD Address: 00:17:CA:5A:D8:F6
Device Name: VE538
LMP Version: 2.0 (0x3) LMP Subversion: 0xc5c
Manufacturer: Cambridge Silicon Radio (10)
Features: 0xff 0xff 0x8f 0xf8 0x1b 0x18 0x00 0x80
<3-slot packets> <5-slot packets> <encryption> <slot offset>
<timing accuracy> <role switch> <hold mode> <sniff mode>
<park state> <RSSI> <channel quality> <SCO link> <HV2 packets>
<HV3 packets> <u-law log> <A-law log> <CVSD> <paging scheme>
<power control> <transparent SCO> <broadcast encrypt>
<enhanced iscan> <interlaced iscan> <interlaced pscan>
<inquiry with RSSI> <extended SCO> <EV4 packets> <EV5 packets>
<AFH cap. slave> <AFH class. slave> <AFH cap. master>
<AFH class. master> <extended features>
Hat vielleicht jemand eine Lösung parat?
Ich versuche eine Bluetooth-Verbindung zwischen meinem Laptop und meinem neuen Motorola VE538 herzustellen. Ich lege also den Schalter für den Bluetooth-Adapter an meinem Laptop um, und bekomme folgende Ausgabe bei dmesg
[ 3578.392959] atkbd.c: Unknown key pressed (translated set 2, code 0xf1 on isa0060/serio0).
[ 3578.392959] atkbd.c: Use 'setkeycodes e071 <keycode>' to make it known.
[ 3578.400796] atkbd.c: Unknown key released (translated set 2, code 0xf1 on isa0060/serio0).
[ 3578.400796] atkbd.c: Use 'setkeycodes e071 <keycode>' to make it known.
[ 3578.994878] usb 2-1: new full speed USB device using uhci_hcd and address 3
[ 3579.150754] usb 2-1: configuration #1 chosen from 1 choice
[ 3579.153170] usb 2-1: New USB device found, idVendor=0a5c, idProduct=2101
[ 3579.153185] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3579.153191] usb 2-1: Product: Foxconn Bluetooth 2.0 plus EDR
[ 3579.153195] usb 2-1: Manufacturer: Broadcom Corp
[ 3579.220218] Bluetooth: HCI USB driver ver 2.9
[ 3579.221925] usbcore: registered new interface driver hci_usb
hciconfig -a
hci0: Type: USB
BD Address: 00:19:7D:E4:0E:C9 ACL MTU: 1017:8 SCO MTU: 64:8
UP RUNNING PSCAN
RX bytes:9282 acl:0 sco:0 events:313 errors:0
TX bytes:677 acl:0 sco:0 commands:99 errors:0
Features: 0xff 0xff 0x8f 0xfe 0x9b 0xf9 0x00 0x80
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH HOLD SNIFF PARK
Link mode: SLAVE ACCEPT
Name: 'Stefan-0'
Class: 0x4a010c
Service Classes: Networking, Capturing, Telephony
Device Class: Computer, Laptop
HCI Ver: 2.0 (0x3) HCI Rev: 0x213b LMP Ver: 2.0 (0x3) LMP Subver: 0x41d3
Manufacturer: Broadcom Corporation (15)
# /etc/init.d/bluetooth status
bluetooth is running.
Aber das Icon in der Notification Area erscheint nicht, wenn ich bei bluetooth-properties auswähle Nur zeigen, wenn ein Adapter vorhanden ist, obwohl der ja vorhanden ist. Mein Handy findet auch meinen Adapter nicht, wohl aber andere PCs.
# hcitool scan
Scanning ...
00:17:CA:5A:D8:F6 VE538
00:22:FD:3E:CA:C1 N95jags
# hcitool info 00:17:CA:5A:D8:F6
Requesting information ...
BD Address: 00:17:CA:5A:D8:F6
Device Name: VE538
LMP Version: 2.0 (0x3) LMP Subversion: 0xc5c
Manufacturer: Cambridge Silicon Radio (10)
Features: 0xff 0xff 0x8f 0xf8 0x1b 0x18 0x00 0x80
<3-slot packets> <5-slot packets> <encryption> <slot offset>
<timing accuracy> <role switch> <hold mode> <sniff mode>
<park state> <RSSI> <channel quality> <SCO link> <HV2 packets>
<HV3 packets> <u-law log> <A-law log> <CVSD> <paging scheme>
<power control> <transparent SCO> <broadcast encrypt>
<enhanced iscan> <interlaced iscan> <interlaced pscan>
<inquiry with RSSI> <extended SCO> <EV4 packets> <EV5 packets>
<AFH cap. slave> <AFH class. slave> <AFH cap. master>
<AFH class. master> <extended features>
Hat vielleicht jemand eine Lösung parat?