PDA

Archiv verlassen und diese Seite im Standarddesign anzeigen : [solved] Server mit fünf Platten, eine lahmt



lkwg82
24.06.09, 21:15
Ich habe keinen Ansatz wodurch ich mir die lahme Datentransferleistung erklären kann.

eine Platte kann nicht mehr als 2Mb/s :confused:
(die 1TB)



# fdisk -l | grep ^Disk | grep sd
Disk /dev/sda: 500.1 GB, 500107862016 bytes
Disk /dev/sdb: 500.1 GB, 500107862016 bytes
Disk /dev/sdc: 500.1 GB, 500107862016 bytes
Disk /dev/sdd: 500.1 GB, 500107862016 bytes
Disk /dev/sde: 1000.2 GB, 1000204886016 bytes



Model=SAMSUNG HE502IJ , FwRev=1AA01113, SerialNo=S1MTJ1BS200518
Model=SAMSUNG HE502IJ , FwRev=1AA01113, SerialNo=S1MTJ1BS200519
Model=SAMSUNG HE502IJ , FwRev=1AA01113, SerialNo=S1MTJ1BS200527
Model=SAMSUNG HE502IJ , FwRev=1AA01113, SerialNo=S1MTJ1BS200526
Model=SAMSUNG HD103UJ , FwRev=1AA01113, SerialNo=S13PJDWS312425


Base Board Information
Manufacturer: Gigabyte Technology Co., Ltd.
Product Name: GA-MA78GM-S2H


Linux vmserver 2.6.24-23-generic #1 SMP Wed Apr 1 21:43:24 UTC 2009 x86_64 GNU/Linux

System: ubuntu LTS 8.04
CPU : AMD Phenom(tm) II X4 920 Processor
RAM: 4GB

ist einer der Sata-Slots vielleicht zu lahm, oder schraubt der die Datentakt runter o.ä.???

Aqualung
24.06.09, 21:26
was sagt


hdparm -i /dev/sde

vs.


hdparm -i /dev/sda

lkwg82
24.06.09, 21:52
# hdparm -i /dev/sda

/dev/sda:

Model=SAMSUNG HE502IJ , FwRev=1AA01113, SerialNo=S1MTJ1BS200518
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
BuffType=DualPortCache, BuffSize=16384kB, MaxMultSect=16, MultSect=?0?
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=976773168
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive conforms to: unknown: ATA/ATAPI-3,4,5,6,7

* signifies the current active mode


# hdparm -i /dev/sde

/dev/sde:

Model=SAMSUNG HD103UJ , FwRev=1AA01113, SerialNo=S13PJDWS312425
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
BuffType=DualPortCache, BuffSize=32767kB, MaxMultSect=16, MultSect=?16?
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=1953525168
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: unknown: ATA/ATAPI-3,4,5,6,7

* signifies the current active mode


# hdparm -t /dev/sd{a,e}

/dev/sda:
Timing buffered disk reads: 266 MB in 3.01 seconds = 88.37 MB/sec

/dev/sde:
Timing buffered disk reads: 6 MB in 3.36 seconds = 1.79 MB/sec

OliverH
24.06.09, 23:11
Hängen die Platten alle am selben Controller?
Was sagt lspci -vv?
Was sagt lsmod?

Ich vermute, dass die 5. Platte an einem anderen Controller hängt, als die anderen 4, und hier der Treiber Probleme macht!?

OliverH
24.06.09, 23:18
Schau mal hier:


http://ubuntuforums.org/showthread.php?t=760121


Da hat jemand das gleiche Problem mit der selben Hardware ;)

Ps. Gefunden über Google "ATI SB700 2.6.24 slow"

lkwg82
24.06.09, 23:23
# lspci -vv
00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge
Subsystem: Advanced Micro Devices [AMD] RS780 Host Bridge
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 3: Memory at <ignored> (64-bit, non-prefetchable)
Capabilities: [c4] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=12 MastHost- DefDir- DUL-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 3.00
Link Frequency 0: [a]
Link Error 0: <Prot+ <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [54] HyperTransport: UnitID Clumping
Capabilities: [40] HyperTransport: Retry Mode
Capabilities: [9c] HyperTransport: #1a
Capabilities: [f8] HyperTransport: #1c

00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fdd00000-fdefffff
Prefetchable memory behind bridge: 00000000d8000000-00000000dfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [44] HyperTransport: MSI Mapping
Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx)

00:0a.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fda00000-fdafffff
Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 10, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4151
Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Unknown device 9600
Capabilities: [b8] HyperTransport: MSI Mapping

00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Unknown device b002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at ff00 [size=8]
Region 1: I/O ports at fe00 [size=4]
Region 2: I/O ports at fd00 [size=8]
Region 3: I/O ports at fc00 [size=4]
Region 4: I/O ports at fb00 [size=16]
Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] #12 [0010]

00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Unknown device 5004
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]

00:12.1 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI1 Controller (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Unknown device 5004
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]

00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Unknown device 5004
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port

00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Unknown device 5004
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]

00:13.1 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI1 Controller (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Unknown device 5004
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]

00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Unknown device 5004
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port

00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a)
Subsystem: Giga-byte Technology Unknown device 4385
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort- >SERR+ <PERR+
Capabilities: [b0] HyperTransport: MSI Mapping

00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller (prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology Unknown device 5002
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at fa00 [size=16]
Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable-
Address: 00000000 Data: 0000

00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller
Subsystem: ATI Technologies Inc SB700/SB800 LPC host controller
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: fdb00000-fdbfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-

00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Unknown device 5004
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe028000 (32-bit, non-prefetchable) [size=4K]

00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] HyperTransport Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Revision ID: 3.00
Link Frequency: [a]
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-

00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]

00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Link Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3200 Graphics (prog-if 00 [VGA controller])
Subsystem: Giga-byte Technology Unknown device d000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at ee00 [size=256]
Region 2: Memory at fdee0000 (32-bit, non-prefetchable) [size=64K]
Region 5: Memory at fdd00000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000

01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller
Subsystem: ATI Technologies Inc RS780 Azalia controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fdefc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000

02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
Subsystem: Giga-byte Technology Unknown device e000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 510
Region 0: I/O ports at de00 [size=256]
Region 2: Memory at fdfff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at fdfe0000 (64-bit, prefetchable) [size=64K]
[virtual] Expansion ROM at fdf00000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000fee0f00c Data: 4159
Capabilities: [70] Express Endpoint IRQ 1
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <8us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <512ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [b0] MSI-X: Enable- Mask- TabSize=2
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data



# lsmod | sort
ac 8328 0
af_packet 27272 2
ahci 33284 10
async_memcpy 4608 1 raid456
async_tx 10484 3 raid456,async_xor,async_memcpy
async_xor 6144 1 raid456
ata_generic 9988 0
atiixp 6672 0 [permanent]
battery 16776 0
bitblit 7424 1 fbcon
button 10912 0
cdrom 41512 1 sr_mod
container 6656 0
cpufreq_conservative 10632 0
cpufreq_ondemand 11152 4
cpufreq_powersave 3200 0
cpufreq_stats 8416 0
cpufreq_userspace 6180 0
dm_mirror 26368 0
dm_mod 71160 10 dm_multipath,dm_mirror,dm_snapshot
dm_multipath 23056 0
dm_snapshot 20680 0
dock 12960 0
ehci_hcd 41996 0
evdev 14976 2
fan 6792 0
fbcon 46336 0
font 10112 1 fbcon
freq_table 6464 3 cpufreq_stats,cpufreq_ondemand,powernow_k8
fuse 56112 3
hwmon_vid 5120 1 it87
i2c_core 28544 1 i2c_piix4
i2c_piix4 11148 0
ide_core 136600 1 atiixp
iptable_filter 4608 1
iptable_mangle 4480 0
iptable_nat 9604 0
ip_tables 24104 3 iptable_filter,iptable_mangle,iptable_nat
ipv6 311848 40
it87 26896 0
jfs 189648 2
kvm 131800 1 kvm_amd
kvm_amd 29196 0
libata 176560 4 pata_atiixp,ata_generic,ahci,pata_acpi
linear 7424 0
loop 21508 0
lp 14916 0
md_mod 88220 8 raid10,raid456,raid1,raid0,multipath,linear
Module Size Used by
multipath 11008 0
nf_conntrack 79216 4 xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4
nf_conntrack_ipv4 21904 4 iptable_nat
nf_nat 23980 1 iptable_nat
ohci_hcd 28956 0
output 5632 1 video
parport 44300 2 lp,parport_pc
parport_pc 41128 1
pata_acpi 9856 0
pata_atiixp 10496 2
pci_hotplug 34608 1 shpchp
pcspkr 4992 0
powernow_k8 16608 0
processor 40424 2 powernow_k8,thermal
psmouse 46236 0
r8169 36868 0
raid0 9472 0
raid10 26368 0
raid1 26880 2
raid456 131360 0
reiserfs 246912 2
sbs 17808 0
sbshc 8960 1 sbs
scsi_mod 178488 4 sr_mod,sg,sd_mod,libata
sd_mod 33280 12
serio_raw 9092 0
sg 41880 0
shpchp 38172 0
snd 70856 11 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,sn d_hwdep,snd_seq_dummy,snd_seq_oss,snd_rawmidi,snd_ seq,snd_timer,snd_seq_device
snd_hda_intel 442200 0
snd_hwdep 12552 1 snd_hda_intel
snd_mixer_oss 20224 1 snd_pcm_oss
snd_page_alloc 13200 2 snd_hda_intel,snd_pcm
snd_pcm 92168 2 snd_hda_intel,snd_pcm_oss
snd_pcm_oss 47648 0
snd_rawmidi 29856 1 snd_seq_midi
snd_seq 63232 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event
snd_seq_device 10644 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq
snd_seq_dummy 5764 0
snd_seq_midi 10688 0
snd_seq_midi_event 10112 2 snd_seq_oss,snd_seq_midi
snd_seq_oss 38912 0
snd_timer 27912 2 snd_pcm,snd_seq
softcursor 3712 1 bitblit
soundcore 10400 1 snd
sr_mod 20132 0
thermal 19744 0
tileblit 4096 1 fbcon
tun 14336 1
usbcore 170288 3 ohci_hcd,ehci_hcd
video 23444 0
vmci 59088 2 vsock
vmmon 79984 19
vmnet 52052 17
vsock 27664 0
wmi_acer 11076 0
xfs 562152 1
xor 7184 2 raid456,async_xor
x_tables 23560 4 xt_state,xt_tcpudp,iptable_nat,ip_tables
xt_state 4096 2
xt_tcpudp 4992 8

OliverH
24.06.09, 23:28
Hast du dir den Link angesehen?

Zeig uns mal die Ausgabe von dmesg!

lkwg82
24.06.09, 23:32
so, mal schauen, starte gerade neu.... (versuche deinen Tipp mit driver blacklisten)

lkwg82
24.06.09, 23:37
in der DMESG Ausgabe stand dieses SLOW DOWN aus dem Link.



[ 33.344942] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14
[ 33.344975] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15
[ 33.661138] ata5.00: ATAPI: SONY DVD RW DW-U18A, UYS1, max UDMA/33
[ 33.832655] ata5.00: configured for UDMA/33
[ 34.004138] ata6.00: HPA unlocked: 1953523055 -> 1953525168, native 1953525168
[ 34.004177] ata6.00: ATA-7: SAMSUNG HD103UJ, 1AA01113, max UDMA7
[ 34.004210] ata6.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 34.004248] ata6.00: simplex DMA is claimed by other device, disabling DMA
[ 34.012248] ata6.00: configured for PIO4

lkwg82
24.06.09, 23:41
merke gerade, daß er mit anderem Kernel gestartet ist und demzufolge nciht von den Änderungen profitiert

lkwg82
24.06.09, 23:47
[ 32.721319] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 32.727730] ata6.00: ATA-7: SAMSUNG HE502IJ, 1AA01113, max UDMA7
[ 32.727764] ata6.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 32.734240] ata6.00: configured for UDMA/133
[ 33.871142] ReiserFS: md0: using ordered data mode
[ 41.513285] Adding 16777208k swap on /dev/mapper/data-swap. Priority:-1 extents:1 across:16777208k
[ 48.880352] ReiserFS: dm-2: using ordered data mode



# hdparm -t /dev/sde

/dev/sde:
Timing buffered disk reads: 262 MB in 3.00 seconds = 87.30 MB/sec


Super Leistung, Danke!

lkwg82
24.06.09, 23:49
kann man den Thementitel noch auf "[Solved] " ändern?