Hi,
ich habe von einem Kumpel ein altes NoName Notebook bekommen.
Leider weiß ich nicht viel über diese Notebook.
Es ist eine Intel Celeron CPU mit 1000MHz
256MB RAM
Grafik laut BIOS 8MB keine Ahnung welcher Hersteller
Ich habe Ubuntu 8.10 installiert. Nun habe ich folgendes Problem:
Das Bild ist in der Mitte und hat eine Auflösung von 800x600 es sind schwarze Balken um das Bild drumherum. Über die Einstellungen von Gnome oder KDE kann man auch nur maximal 800x600 einstellen. Daraus schließe ich, dass die xorg.conf editiert werden muss.
Seltsamerweise ist meine xorg.conf (unter /etc/X11/) komplett leer!?!
Hat jemand eine Idee wie ich jetzt ein volles Bild ohne schwarze Balken in einer Auflösung von 1280x1024 bekomme?
Danke
Titzi266
pferdefreund
09.11.08, 14:04
Wird da überhaupt xorg verwendet - oder eventuell framebuffer ?
Eventuell mal knoppix starten und von da x11-config kopieren.
stefan.becker
09.11.08, 14:29
Und vor allem mal "keine Ahnung was es ist" durch exakte Angaben ersetzen.
lspci und Konsorten bringen doch sicherlich genauere Angaben.
Also meine xorg.conf sieht so aus:
Section "Device"
Identifier "Configured Video Device"
EndSection
Section "Monitor"
Identifier "Configured Monitor"
EndSection
Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
EndSection
Bei lspci kommt folgendes raus:
root@norax:~# lspci
00:00.0 Host bridge: ALi Corporation M1621 (rev 01)
00:01.0 PCI bridge: ALi Corporation PCI to AGP Controller (rev 01)
00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:03.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01)
00:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:06.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
00:07.0 ISA bridge: ALi Corporation M1533/M1535/M1543 PCI to ISA Bridge [Aladdin IV/V/V+]
00:08.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 01)
00:0f.0 IDE interface: ALi Corporation M5229 IDE (rev c3)
01:00.0 VGA compatible controller: Trident Microsystems CyberBlade/i1 (rev 5d)
root@norax:~#
Wie müsste ich jetzt die xorg.conf ändern für eine Auflösung von 1280x1024? Oder wo finde ich die Framebufferdatei, falls es in dieser Datei konfiguriert ist?
stefan.becker
09.11.08, 15:21
Du hast wohl eine der neuen selbstkonfigurierenden Xorg-Versionen.
Hast du eventuell ein Knoppix zur Hand und kannst damit booten, eventuell dann einige Einstellungen von Knoppix übernehmen?
Nein habe leider kein Knoppix.
Ich habe aber auf meinem anderen Rechner auch Ubuntu 8.10 installiert mit der Auflösung von 1280x1024.
Könnte ich von diesem Rechner die xorg.conf nehmen und auf diese Notebook kopieren? Wird nicht funktionieren oder? (Dort steht auch keine Auflösung drin. :( )
Was kann ich noch machen?
Ich habe mal Knoppix runtergeladen und es versucht. Unter Knoppix hat er wenigstnes eine Auflösung von 1024x768 und keine schwarzen Balken mehr.
Ich habe die xorg.conf von Knoppix genommen und in Ubuntu überschrieben.
Bringt leider nur fehler. Beim Start von X findet er fehler in der Konfiguration und X lässt sich nur im niedrigen Grafikmodus starten. Ist dann wieder 800x600 und schwarze Balken. :(
Trotzdem danke schon mal an alle.
Nochjemand eine Idee?
Hi,
da meine Glaskugel wieder in Reparatur ist, mach doch mal folgendes:
- die ursprüngliche xorg.conf wiederherstellen
- nach dem Start von X mit 800x600 hier die /var/log/Xorg.0.log posten
Da steht normalerweise alles drin, was man wissen muss um die Fehler beheben zu können. Ich tippe mal auf falsche horizontale/vertikale Frequenz - aber wie gesagt, Glaskugel putt. :D
stefan.becker
09.11.08, 19:32
Man sollte natürlich nicht blind kopieren, sondern nur Einstellungen für "device" und "screen".
Außerdem ist halt die Frage, ob SchnickSchnackBuntu die passenden Treiber hat. Das kann ich dir allerdings nicht sagen, musst halt mal selbst recherchieren.
Hi,
der "normale" VESA-Treiber reicht. Auch bei SchnickSchnack. *lol* Linux ist Linux und X.org ist X.org, egal was draufsteht.
Wie starte ich mein Ubuntu bzw X denn mit dem VESA Treiber?
Hi,
dazu brauchst du eine (selbst-)konfigurierte xorg.conf. Da kann man den Treiber dann eintragen:
Section "Device"
Identifier "MyVideocard"
Driver "vesa"
...
Dein X konfiguriert sich aber z.Z. selbst. Also müsste man zuerst wissen, mit was es nicht klar kommt und dann entsprechend anpassen. Die "Try & Error"-Methode ist hier unnötig mühsam, da X schon sehr gesprächig ist und man so gezielt handeln kann.
Also denke noch mal über meinen ersten Vorschlag nach. Die ganze Aktion dauert ja auch nur ein paar Sekunden ....
Also habe folgendes gemacht:
- die ursprüngliche xorg.conf wiederhergestellt
- nach dem Start von X mit 800x600 die /var/log/Xorg.0.log angesehen.
/var/log/Xorg.0.log:
X.Org X Server 1.5.2
Release Date: 10 October 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-19-server i686 Ubuntu
Current Operating System: Linux norax 2.6.27-7-generic #1 SMP Tue Nov 4 19:33:20 UTC 2008 i686
Build Date: 24 October 2008 08:00:16AM
xorg-server 2:1.5.2-2ubuntu3 (buildd@rothera.buildd)
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Tue Nov 11 20:16:26 2008
(==) Using config file: "/etc/X11/xorg.conf"
(==) No Layout section. Using the first Screen section.
(**) |-->Screen "Default Screen" (0)
(**) | |-->Monitor "Configured Monitor"
(**) | |-->Device "Configured Video Device"
(==) Automatically adding devices
(==) Automatically enabling devices
(==) No FontPath specified. Using compiled-in default.
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(II) Open ACPI successful (/var/run/acpid.socket)
(II) Loader magic: 0x81d9a40
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 4.1
X.Org XInput driver : 2.1
X.Org Server Extension : 1.1
X.Org Font Renderer : 0.6
(II) Loader running on linux
(++) using VT number 7
(--) PCI:*(0@1:0:0) Trident Microsystems CyberBlade/i1 rev 93, Mem @ 0xef800000/0, 0xee900000/0, 0xef000000/0, BIOS @ 0x????????/65536
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 1.1
(==) AIGLX enabled
(==) Exporting typical set of GLX visuals
(II) Loading extension GLX
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules//fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 1.5.2, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.6
(II) Loading font FreeType
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension XFree86-DRI
(II) Scanning /usr/share/xserver-xorg/pci directory for additional PCI ID's supported by the drivers
(II) Matched trident from file name trident.ids
(==) Matched trident for the autoconfigured driver
(==) Assigned the driver to the xf86ConfigLayout
(II) LoadModule: "trident"
(II) Loading /usr/lib/xorg/modules/drivers//trident_drv.so
(II) Module trident: vendor="X.Org Foundation"
compiled for 1.5.0, module version = 1.3.0
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 4.1
(II) TRIDENT: driver for Trident chipsets: tvga9000, tvga9000i, tvga8900c,
tvga8900d, tvga9200cxr, tgui9400cxi, cyber9320, cyber9388, cyber9397,
cyber9397dvd, cyber9520, cyber9525dvd, cyberblade/e4, tgui9420dgi,
tgui9440agi, tgui9660, tgui9680, providia9682, providia9685,
cyber9382, cyber9385, 3dimage975, 3dimage985, blade3d, cyberbladei7,
cyberbladei7d, cyberbladei1, cyberbladei1d, cyberbladeAi1,
cyberbladeAi1d, bladeXP, cyberbladeXPAi1, cyberbladeXP4, XP5
(II) Primary Device is: PCI 01@00:00:0
(WW) Falling back to old probe method for trident
(--) Assigning device section with no busID to primary device
(--) Chipset cyberbladeAi1d found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) TRIDENT(0): Creating default Display subsection in Screen section
"Default Screen" for depth/fbbpp 24/32
(==) TRIDENT(0): Depth 24, (==) framebuffer bpp 32
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 0.1.0
ABI class: X.Org Video Driver, version 4.1
(II) TRIDENT(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(==) TRIDENT(0): RGB weight 888
(==) TRIDENT(0): Default visual is TrueColor
(==) TRIDENT(0): Using gamma correction (1.0, 1.0, 1.0)
(==) TRIDENT(0): Using XAA for acceleration
(==) TRIDENT(0): Linear framebuffer at 0xEF800000
(--) TRIDENT(0): IO registers at 0xEE900000
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.1.0
ABI class: X.Org Video Driver, version 4.1
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 4.1
(II) TRIDENT(0): initializing int10
(WW) TRIDENT(0): Bad V_BIOS checksum
(II) TRIDENT(0): Primary V_BIOS segment is: 0xc000
(II) TRIDENT(0): VESA BIOS detected
(II) TRIDENT(0): VESA VBE Version 2.0
(II) TRIDENT(0): VESA VBE Total Mem: 8192 kB
(II) TRIDENT(0): VESA VBE OEM: Trident CYBER 8620
(II) TRIDENT(0): VESA VBE OEM Software Rev: 2.0
(II) TRIDENT(0): VESA VBE OEM Vendor: TRIDENT MICROSYSTEMS INC.
(II) TRIDENT(0): VESA VBE OEM Product: CYBER 8620
(II) TRIDENT(0): VESA VBE OEM Product Rev: B m 7.0 (03.03)
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) TRIDENT(0): VESA VBE DDC read failed
(--) TRIDENT(0): Revision is 122
(--) TRIDENT(0): Found CyberBlade/DSTN/Ai1 chip
(--) TRIDENT(0): RAM type is SDRAM
(--) TRIDENT(0): Using SW cursor
(--) TRIDENT(0): VideoRAM: 8192 kByte
(--) TRIDENT(0): TFT Panel 1024x768 found
(--) TRIDENT(0): Memory Clock is 100.23 MHz
(==) TRIDENT(0): Min pixel clock is 12 MHz
(--) TRIDENT(0): Max pixel clock is 115 MHz
(II) TRIDENT(0): Configured Monitor: Using default hsync range of 31.50-37.90 kHz
(II) TRIDENT(0): Configured Monitor: Using default vrefresh range of 50.00-70.00 Hz
(WW) TRIDENT(0): Unable to estimate virtual size
(II) TRIDENT(0): Clock range: 12.00 to 115.00 MHz
(II) TRIDENT(0): Not using default mode "640x350" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "320x175" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "640x400" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "320x200" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "720x400" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "360x200" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "640x480" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "320x240" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "640x480" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "320x240" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "640x480" (hsync out of range)
(II) TRIDENT(0): Not using default mode "320x240" (hsync out of range)
(II) TRIDENT(0): Not using default mode "800x600" (hsync out of range)
(II) TRIDENT(0): Not using default mode "400x300" (hsync out of range)
(II) TRIDENT(0): Not using default mode "800x600" (hsync out of range)
(II) TRIDENT(0): Not using default mode "400x300" (hsync out of range)
(II) TRIDENT(0): Not using default mode "800x600" (hsync out of range)
(II) TRIDENT(0): Not using default mode "400x300" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1024x768" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "512x384" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "1024x768" (hsync out of range)
(II) TRIDENT(0): Not using default mode "512x384" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1024x768" (hsync out of range)
(II) TRIDENT(0): Not using default mode "512x384" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1024x768" (hsync out of range)
(II) TRIDENT(0): Not using default mode "512x384" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1024x768" (hsync out of range)
(II) TRIDENT(0): Not using default mode "512x384" (hsync out of range)
(II) TRIDENT(0): Removing mode (1152x864) larger than the LCD panel (1024x768)
(II) TRIDENT(0): Not using default mode "1152x864" (unknown reason)
(II) TRIDENT(0): Not using default mode "576x432" (hsync out of range)
(II) TRIDENT(0): Removing mode (1280x960) larger than the LCD panel (1024x768)
(II) TRIDENT(0): Not using default mode "1280x960" (unknown reason)
(II) TRIDENT(0): Not using default mode "640x480" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1280x960" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "640x480" (hsync out of range)
(II) TRIDENT(0): Removing mode (1280x1024) larger than the LCD panel (1024x768)
(II) TRIDENT(0): Not using default mode "1280x1024" (unknown reason)
(II) TRIDENT(0): Not using default mode "640x512" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1280x1024" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "640x512" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1280x1024" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "640x512" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "800x600" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "800x600" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "800x600" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "800x600" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "800x600" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) TRIDENT(0): Not using default mode "896x672" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) TRIDENT(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) TRIDENT(0): Not using default mode "928x696" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) TRIDENT(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) TRIDENT(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) TRIDENT(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "832x624" (hsync out of range)
(II) TRIDENT(0): Not using default mode "416x312" (hsync out of range)
(II) TRIDENT(0): Removing mode (1152x864) larger than the LCD panel (1024x768)
(II) TRIDENT(0): Not using default mode "1152x864" (unknown reason)
(II) TRIDENT(0): Not using default mode "576x432" (hsync out of range)
(II) TRIDENT(0): Removing mode (1152x864) larger than the LCD panel (1024x768)
(II) TRIDENT(0): Not using default mode "1152x864" (unknown reason)
(II) TRIDENT(0): Not using default mode "576x432" (hsync out of range)
(II) TRIDENT(0): Removing mode (1152x864) larger than the LCD panel (1024x768)
(II) TRIDENT(0): Not using default mode "1152x864" (unknown reason)
(II) TRIDENT(0): Not using default mode "576x432" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1152x864" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "576x432" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1152x864" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "576x432" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1152x864" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "576x432" (hsync out of range)
(II) TRIDENT(0): Removing mode (1360x768) larger than the LCD panel (1024x768)
(II) TRIDENT(0): Not using default mode "1360x768" (unknown reason)
(II) TRIDENT(0): Not using default mode "680x384" (hsync out of range)
(II) TRIDENT(0): Removing mode (1360x768) larger than the LCD panel (1024x768)
(II) TRIDENT(0): Not using default mode "1360x768" (unknown reason)
(II) TRIDENT(0): Not using default mode "680x384" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1400x1050" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "700x525" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1400x1050" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "700x525" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1400x1050" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "700x525" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1400x1050" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "700x525" (hsync out of range)
(II) TRIDENT(0): Removing mode (1440x900) larger than the LCD panel (1024x768)
(II) TRIDENT(0): Not using default mode "1440x900" (unknown reason)
(II) TRIDENT(0): Not using default mode "720x450" (hsync out of range)
(II) TRIDENT(0): Removing mode (1600x1024) larger than the LCD panel (1024x768)
(II) TRIDENT(0): Not using default mode "1600x1024" (unknown reason)
(II) TRIDENT(0): Not using default mode "800x512" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1680x1050" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "840x525" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1680x1050" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "840x525" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1680x1050" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "840x525" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1680x1050" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "840x525" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1680x1050" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "840x525" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1920x1080" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "960x540" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1920x1200" (insufficient memory for mode)
(II) TRIDENT(0): Not using default mode "960x600" (hsync out of range)
(II) TRIDENT(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) TRIDENT(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "2048x1536" (insufficient memory for mode)
(II) TRIDENT(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "2048x1536" (insufficient memory for mode)
(II) TRIDENT(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "2048x1536" (insufficient memory for mode)
(II) TRIDENT(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(--) TRIDENT(0): Virtual size is 800x600 (pitch 800)
(**) TRIDENT(0): *Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz
(II) TRIDENT(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(**) TRIDENT(0): *Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz
(II) TRIDENT(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
(**) TRIDENT(0): *Default mode "640x480": 25.2 MHz, 31.5 kHz, 59.9 Hz
(II) TRIDENT(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(**) TRIDENT(0): *Default mode "400x300": 20.0 MHz, 37.9 kHz, 60.3 Hz (D)
(II) TRIDENT(0): Modeline "400x300"x60.3 20.00 400 420 484 528 300 300 302 314 doublescan +hsync +vsync (37.9 kHz)
(**) TRIDENT(0): *Default mode "400x300": 18.0 MHz, 35.2 kHz, 56.3 Hz (D)
(II) TRIDENT(0): Modeline "400x300"x56.3 18.00 400 412 448 512 300 300 301 312 doublescan +hsync +vsync (35.2 kHz)
(**) TRIDENT(0): *Default mode "320x240": 12.6 MHz, 31.5 kHz, 60.1 Hz (D)
(II) TRIDENT(0): Modeline "320x240"x60.1 12.59 320 328 376 400 240 245 246 262 doublescan -hsync -vsync (31.5 kHz)
(==) TRIDENT(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/lib/xorg/modules//libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.2.0
ABI class: X.Org Video Driver, version 4.1
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprU)
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprU)
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprU)
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/lib/xorg/modules//libint10.so
(II) TRIDENT(0): Initializing int10
(WW) TRIDENT(0): Bad V_BIOS checksum
(II) TRIDENT(0): Primary V_BIOS segment is: 0xc000
(II) TRIDENT(0): Overriding Horizontal timings.
(II) TRIDENT(0): Shadow on
(II) TRIDENT(0): H-timing shadow registers: 0xa3 0x00 0x84 0x94
(II) TRIDENT(0): H-timing registers: 0x7f 0x63 0x63 0x82 0x69 0x19
(II) TRIDENT(0): V-timing shadow registers: 0x24 0xf5 0x03 0x09 0x24 (0x08)
(II) TRIDENT(0): V-timing registers: 0x72 0xf0 0x59 0x2d 0x57 0x00 0x00
(II) TRIDENT(0): Setting BIOS Mode: 6d for: 800x600
(II) TRIDENT(0): Found Clock 130.00 n=219 m=23 k=0
(II) TRIDENT(0): Using 1447 scanlines of offscreen memory for area's
(II) TRIDENT(0): Using 1838208 bytes of offscreen memory for linear (offset=0x63f380)
(II) TRIDENT(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
CPU to Screen color expansion
Solid Horizontal and Vertical Lines
Image Writes
Setting up tile and stipple cache:
32 128x128 slots
8 256x256 slots
(==) TRIDENT(0): Backing store disabled
(II) TRIDENT(0): DPMS enabled
(II) TRIDENT(0): Trident Video Flags: VID_ZOOM_INV
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) AIGLX: Screen 0 is not DRI capable
(II) AIGLX: Loaded and initialized /usr/lib/dri/swrast_dri.so
(II) GLX: Initialized DRISWRAST GL provider for screen 0
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 2.0.99
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.1
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Configuring as mouse
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) config/hal: Adding input device SynPS/2 Synaptics TouchPad
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules/input//synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 0.15.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.1
(II) Synaptics touchpad driver version 0.15.2
(II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
(II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
(**) Option "Device" "/dev/input/event6"
(--) SynPS/2 Synaptics TouchPad touchpad found
(**) SynPS/2 Synaptics TouchPad: always reports core events
(II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
(II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
(II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
(--) SynPS/2 Synaptics TouchPad touchpad found
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) AT Translated Set 2 keyboard: xkb_rules: "evdev"
(**) Option "xkb_model" "pc105"
(**) AT Translated Set 2 keyboard: xkb_model: "pc105"
(**) Option "xkb_layout" "de"
(**) AT Translated Set 2 keyboard: xkb_layout: "de"
AUDIT: Tue Nov 11 20:16:36 2008: 4802 X: client 4 rejected from local host ( uid=0 gid=0 pid=4968 )
Sodele,
geht doch. :D
Wenn es richtig ist, dass das LCD max. 1024x768 darstellen kann, dann sind diese beiden Zeilen wohl das Problem, dasss nur mit 800x600 gefahren wird:
(II) TRIDENT(0): Not using default mode "1024x768" (vrefresh out of range)
(II) TRIDENT(0): Not using default mode "1024x768" (hsync out of range)
Deswegen trage mal die für dein LCD Panel max. gültigen Werte in die xorg.conf ein:
Section "Monitor"
Identifier "Configured Monitor"
HorizSync 25-64
VertRefresh 50-60
EndSection
Die Werte sind nur Erfahrungswerte von mir. Falls das immer noch nicht wie gewünscht funktioniert, setze mal den 2. Wert (hinter dem "-") herunter. Sobald dann die gewünschte Auflösung möglich ist (mal mit STRG- oder STRG+ andere Auflösungen probieren), kann man das noch verfeinern.
Hoffe es hilft
Es hat funktioniert!!! :)
Danke an Alle!!!
Powered by vBulletin® Version 4.2.5 Copyright ©2024 Adduco Digital e.K. und vBulletin Solutions, Inc. Alle Rechte vorbehalten.