Hallo,
beim Einrichten meines Druckers bekomme ich die Meldung, das keine Parallele Schnittstelle vorhanden ist.
Im Bios ist die Schnittstelle ordnungsgemäß eingestellt und unter WinXP funktioniert die Schnittstelle ebenfalls einwandfrei.
Was kann ich tun um die Parallele Schnittstelle unter Opensuse 11 ordnungsgemäß zu installieren / konfigurieren und wie kann ich das überprüfen??
Gruß Daniel
Kernelmodule geladen?
Prüfen:
/sbin/lsmod | grep parport
und
dmesg | grep parport
Weggentaler
27.10.08, 19:19
Hier die Meldungen (Ich verstehe das nicht):
richard@linux-uw46:~> /sbin/lsmod | grep parport
parport_pc 55100 1
parport 52948 3 lp,parport_pc,ppdev
richard@linux-uw46:~> dmesg | grep parport
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA
]
parport0: Legacy device
parport_pc 00:08: disabled
parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
parport 0x378: You gave this address, but there is probably no parallel port the
re!
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
parport_pc 00:08: activated
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA ]
parport0: Legacy device
lp0: using parport0 (interrupt-driven).
parport_pc 00:08: disabled
parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
parport 0x378: You gave this address, but there is probably no parallel port the re!
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
parport 0x378: You gave this address, but there is probably no parallel port the re!
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
parport_pc 00:08: activated
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA ]
parport0: Legacy device
lp0: using parport0 (interrupt-driven).
hi,
evtl. hilfreich ;
http://www.linux-community.de/Neues/story?storyid=21826
Existiert den überhaupt /dev/parport0 ?
Greeez Oli
Weggentaler
07.11.08, 22:22
Habe in modeprobe.conf.local eingefügt:
options parport_pc io=0x378 irq=7 dma=3
und er lässt sich ansprechen.
dmesg meldet:
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
Powered by vBulletin® Version 4.2.5 Copyright ©2024 Adduco Digital e.K. und vBulletin Solutions, Inc. Alle Rechte vorbehalten.