raws17
15.09.08, 08:21
Hallo,
versuche mein WOL anzubekommen.
ethtool funktioniert bei mir nicht(Version 6):
[root@host ~]# ethtool eth0
Settings for eth0:
No data available
Output von lspci -vv
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI
Fast Ethernet (rev 90)
Subsystem: ASRock Incorporation: Unknown device 0900
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at dc00 [size=256]
Region 1: Memory at cfffb000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at fffe0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Also meine Netzwerkkarte ist eine OnBoard Karte "SIS 900"
Mainboard ist ein ASRock K7S41
Ich benutze den SME Server -> www.smeserver.org
WOL ist im Bios aktiviert und hat mit WInXP vorher auch funktioniert.
Kann ich das auch mit mii-tool einstellen? Oder geht das NUR mit ethtool?
Danke für alle helfenden Beiträge :)
raws17
versuche mein WOL anzubekommen.
ethtool funktioniert bei mir nicht(Version 6):
[root@host ~]# ethtool eth0
Settings for eth0:
No data available
Output von lspci -vv
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI
Fast Ethernet (rev 90)
Subsystem: ASRock Incorporation: Unknown device 0900
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at dc00 [size=256]
Region 1: Memory at cfffb000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at fffe0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Also meine Netzwerkkarte ist eine OnBoard Karte "SIS 900"
Mainboard ist ein ASRock K7S41
Ich benutze den SME Server -> www.smeserver.org
WOL ist im Bios aktiviert und hat mit WInXP vorher auch funktioniert.
Kann ich das auch mit mii-tool einstellen? Oder geht das NUR mit ethtool?
Danke für alle helfenden Beiträge :)
raws17