[WLAN]Mein Netgear wg111v3, die WEP128Bitverschlüsselung und ich

[BehrBor]

Tja was soll ich noch sagen. Ich bin mittelschwer bis extrem am verzweifel. Stöber jetzt schon den ganzen tag nach informationen und bekomm nix sinniges zusammen.

Also ausgangssituation:
Frisch aufgesetztes Ubuntu (8.04) nebst nem WinXP
wg111v3 stick - läuft

aber keine verbindung zum router.
WLAN netz wird erkannt, ich tipp mienen schlüssel ien. und dann versucht er zu verbinden.
klappt aber nicht kanz

ich nutz das tool knetworkmanager, und habs auch schon mit "iwconfig essid netz key schlüssel" versucht


einer ne idee??

[jeebee]

wenn mit iwconfig dann
iwconfig interface essid name
iwconfig interface key s:ascii-key
wobei du interface mit dem namen deines wlan-interfaces (wlan0, eth1,...) ersetzen musst, name mit der essid deines wlans und ascii-key mit dem wep-key.

[BehrBor]

ja meint ich ja. also das interface hatte ich schon noch mit eingetragen. und mit dem ascii key gehts nicht (24 oder 26 zeichen lang) und wenn ich das s weglassen nimmt der das dingen als hexkey.. geht aber auch nicht

[jeebee]

Ich denk der ascii key sollte für 128bit genau 13 zeichen lang sein. Alternativ ohne s: wär dasselbe ein 26 zeichen langer hex-string (13byte).

Kannst du mal noch die Ausgabe von
dmesg | tail -n 30 posten nachdem du versucht hast dich zu verbinden?

[BehrBor]

ok.. dauert allerdings was.. weil die kiste steh zuhause und bin hier auf der arbeit :D

[jeebee]

ok, ich bin auch auf der arbeit, aber so n bisschen support neben dem arbeiten kann ja nicht schaden ;)

[BehrBor]

jo.. ich versuchs ja auch :D

[ThE_FiSh]

bekommste ne ip vom router ?
wenn nicht vllt mal mit


dhclient interfacename
versuchen

[BehrBor]

nein ich bekomm keine ip vom router.



sidd@sidd:~$ dmesg | tail -n 30
[ 46.444660] wlan0: ethernet device 00:1e:2a:3d:e1:9a using NDIS driver: wg111
v3, version: 0x1, NDIS version: 0x500, vendor: 'Realtek RTL8187 Wireless LAN USB
NIC ', 0846:4260.F.conf
[ 46.444680] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2
PSK; AES/CCMP with WPA, WPA2, WPA2PSK
[ 46.444708] usbcore: registered new interface driver ndiswrapper
[ 47.460727] lp: driver loaded but no devices found
[ 47.635106] Adding 2345448k swap on /dev/sda7. Priority:-1 extents:1 across:
2345448k
[ 48.183809] EXT3 FS on sda8, internal journal
[ 48.309338] device-mapper: uevent: version 1.0.3
[ 48.309365] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-d
evel@redhat.com
[ 49.106314] kjournald starting. Commit interval 5 seconds
[ 49.106607] EXT3 FS on sda9, internal journal
[ 49.106611] EXT3-fs: mounted filesystem with ordered data mode.
[ 49.494612] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 49.827898] No dock devices found.
[ 50.230691] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 380 0+ processors (1 cpu cores) (version 2.20.00)
[ 50.235015] powernow-k8: BIOS error - no PSB or ACPI _PSS objects
[ 51.995852] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 51.995857] apm: overridden by ACPI.
[ 52.158868] ppdev: user-space parallel port driver
[ 52.288074] audit(1220974473.924:2): type=1503 operation="inode_permission" r equested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5141 profile="/usr/sbi n/cupsd" namespace="default"
[ 52.421942] [drm] Initialized drm 1.1.0 20060810
[ 60.100987] eth0: no link during initialization.
[ 60.172867] Bluetooth: Core ver 2.11
[ 60.173513] NET: Registered protocol family 31
[ 60.173517] Bluetooth: HCI device and connection manager initialized
[ 60.173520] Bluetooth: HCI socket layer initialized
[ 60.210453] Bluetooth: L2CAP ver 2.9
[ 60.210457] Bluetooth: L2CAP socket layer initialized
[ 60.285217] Bluetooth: RFCOMM socket layer initialized
[ 60.285630] Bluetooth: RFCOMM TTY layer initialized
[ 60.285633] Bluetooth: RFCOMM ver 1.8


ps:
omg hab ich oben einen ******* geschrieben *g*

[ThE_FiSh]

bist du dir mit dem schlüssel sicher?
mach doch mal testweise die verschlüsslung aus - und sieh nach ob es dann funktioniert.

kannst ja das dsl kabel auch ziehen wenn der test länger dauert

[Grothesk]

Um was genaueres sagen zu können:
http://www.linux-tips-and-tricks.de/index.php/content/view/52/76/

[BehrBor]

ja der key funktioniert..
ich hab mir den im kiskis gespeichert, und kopier den dann einfach nur in das entsprechende feld.
im ubuntu hab ich denn zzt noch einfach so lose in einer txtdatei aufm desktop liegen, weil ich kein plan hab ob ich da das kiskis ans laufen bekomm *g*

aber ich hab jetzt einfach mal die verschlüsselung ausgestellt, und dann komm ich rein. komisch.

ich hab grad einfach mal einen WPA key gesetzt (der router kann beides gleichzeitig) und das funktioniert auch nicht (hier hab ich es aber mit dem k networkmanager gemacht)

[BehrBor]

Um was genaueres sagen zu können:
http://www.linux-tips-and-tricks.de/index.php/content/view/52/76/

das tool ist der meinung ich soll den knetworkmanager benutzen.

/etc/sysconfig/network/config: No such file or directory
Keine config für wlan0 gefunden
kein essid am interface wlan0 gesetzt
klassische netzwerkcofig mit ifup wurde entdeckt. Der knetworkmanager ist wesentlich einfacher.

cooles tool, aber ich hab den networkmanager natürlich als erstes ausprobiert ;)

[Grothesk]

Und die Ausgabedatei sagt (uns)?
Einige Meldungen des skriptes werden auch dadurch bedingt sein, dass es eigentlich auf Suse abgestellt ist. Die wichtigen Dinge werden aber auch für ubuntu gefunden.

[BehrBor]

/etc/sysconfig/network/config: No such file or directory
Keine config für wlan0 gefunden
kein essid am interface wlan0 gesetzt
klassische netzwerkcofig mit ifup wurde entdeckt. Der knetworkmanager ist wesentlich einfacher.

also ich hab das jetzt mal so abgetippt
weil an der ubuntumaschiene hab ich kein netz, und das ist immer ein riesen aufwand irgendwelche texte rüber zu kopieren
desswegen hab ich das jetzt einfach mal abgetippt =)

[Grothesk]

Das nutzt nix.
Ich brauche die komplette Ausgabe. Riesen Aufwand hin oder her.

[Rain_maker]

Ohne die Ausgabedatei ist das Rätselraten.


weil an der ubuntumaschiene hab ich kein netz, und das ist immer ein riesen aufwand irgendwelche texte rüber zu kopieren

Diesen Aufwand solltest Du Dir aber für das Kopieren einer schon fertig vom Script angelegten Datei jetzt machen.

//Edit:

2 Dumme .....

[BehrBor]

ooops..
garnicht gesehn das der ne ausgabedatei angelegt hat :D
naja ok


collectNWData.sh V0.6.1.4
--- Welcher Netzwerkverbindungtyp soll getestet werden?
--- (2) Kabellose Verbindung (WLAN)
--- Welche Netzwerktopologie liegt vor?
--- (1) WLAN access point <---> LinuxClient
--- Auf welchem Rechner wird das Script ausgeführt?
--- (1) LinuxClient

!!! CND0290E: Keine Netzerkkonfiguration für Interface wlan0 gefunden
!!! CND0330E: Es existiert keine WLAN Verbindung und es ist keine ESSID am Interface wlan0 gesetzt
!!! CND0310W: Klassische Netzwerkkonfiguration mit ifup wurde entdeckt. Die Konfiguration mit knetworkmanager ist wesentlich einfacher
--- 2 Fehler gefunden
--- 1 Warnungen gefunden
--- Gehe zu http://www.linux-tips-and-tricks.de/CND um detailiertere Hinweise zu den Fehlermeldungen/Warnungen zu bekommen und wie die Fehler beseitigt werden könnenF

================================================== ================================================== ==============
================================================== ================================================== ==============
*** uname -a
Linux sidd 2.6.24-16-generic #1 SMP Thu Apr 10 13:23:42 UTC 2008 i686 GNU/Linux
================================================== ================================================== ==============
*** SuSE release
cat: /etc/SuSE-release: No such file or directory
================================================== ================================================== ==============
*** /etc/resolv
================================================== ================================================== ==============
*** /etc/hosts
127.0.0.1 localhost
127.0.1.1 sidd
================================================== ================================================== ==============
*** route
Kernel-IP-Routentabelle
Ziel Router Genmask Flags Metric Ref Use Iface
================================================== ================================================== ==============
*** arp
================================================== ================================================== ==============
*** ifconfig
eth0 Link encap:Ethernet Hardware Adresse 00:19:db:6a:e0:14
UP BROADCAST MULTICAST MTU:1500 Metrik:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:18
lo Link encap:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metrik:1
RX packets:72 errors:0 dropped:0 overruns:0 frame:0
TX packets:72 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:5416 (5.2 KB) TX bytes:5416 (5.2 KB)
wlan0 Link encap:Ethernet Hardware Adresse 00:1e:2a:3d:e1:9a
UP BROADCAST MULTICAST MTU:1500 Metrik:1
RX packets:43 errors:0 dropped:0 overruns:0 frame:0
TX packets:43 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:4859 (4.7 KB) TX bytes:5977 (5.8 KB)
================================================== ================================================== ==============
*** ping tests
connect: Network is unreachable
Ping of 195.135.220.3 failed
ping: unknown host www.suse.de
Ping of www.suse.de failed
================================================== ================================================== ==============
*** PCI devices
00:0a.0 Bridge [0680]: nVidia Corporation CK804 Ethernet Controller [10de:0057] (rev a3)
================================================== ================================================== ==============
*** USB devices
Bus 002 Device 006: ID 0421:006d Nokia Mobile Phones
Bus 002 Device 004: ID 0424:a700 Standard Microsystems Corp.
Bus 002 Device 003: ID 0846:4260 NetGear, Inc.
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 002: ID 046d:c025 Logitech, Inc. MX500 Optical Mouse
Bus 001 Device 001: ID 0000:0000
================================================== ================================================== ==============
*** List of loaded modules
| ac | ac97_bus | aes_i586 | af_packet |
| agpgart | ata_generic | battery | bitblit |
| bluetooth | button | cdrom | container |
| cpufreq_conservative | cpufreq_ondemand | cpufreq_powersave | cpufreq_stats |
| cpufreq_userspace | dm_crypt | dm_mod | dock |
| drm | ehci_hcd | evdev | ext3 |
| fan | fat | fbcon | floppy |
| font | forcedeth | freq_table | fuse |
| hid | i2c_core | i2c_nforce2 | iptable_filter |
| ip_tables | jbd | k8temp | l2cap |
| libata | libusual | lp | mbcache |
| ndiswrapper | nls_cp437 | nls_iso8859_1 | ohci_hcd |
| output | parport | parport_pc | pata_acpi |
| pata_amd | pci_hotplug | pcspkr | ppdev |
| processor | radeon | rfcomm | sata_nv |
| sbs | sbshc | scsi_mod | sd_mod |
| sg | shpchp | snd | snd_ac97_codec |
| snd_intel8x0 | snd_mixer_oss | snd_page_alloc | snd_pcm |
| snd_pcm_oss | snd_rawmidi | snd_seq | snd_seq_device |
| snd_seq_dummy | snd_seq_midi | snd_seq_midi_event | snd_seq_oss |
| snd_timer | softcursor | soundcore | sr_mod |
| thermal | tileblit | usbcore | usbhid |
| usb_storage | vfat | video | x_tables |
================================================== ================================================== ==============
*** cat /etc/sysconfig/network/ifcfg-[earwd]* | egrep -v ".*=''"
================================================== ================================================== ==============
*** iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:off/any
Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated
Bit Rate:54 Mb/s Tx-Power:20 dBm Sensitivity=0/3
RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
================================================== ================================================== ==============
*** Actual date for bias of follwing greps
18:59:47 2008-09-09
================================================== ================================================== ==============
*** tail -n 300 /var/log/messages* | grep -i -A 5 'firmware'
================================================== ================================================== ==============
*** grep -i radio /var/log/boot.msg | tail -n 5
/bin/grep: /var/log/boot.msg: No such file or directory
================================================== ================================================== ==============
*** dmesg | grep -i radio | tail -n 5
================================================== ================================================== ==============
*** tail -n 300 /var/log/messages* | -i firmware | tail -n 5
================================================== ================================================== ==============
*** ls -ls /lib/firmware
insgesamt 4
4 drwxr-xr-x 4 root root 4096 2008-04-23 01:29 2.6.24-16-generic
================================================== ================================================== ==============
*** ndiswrapper -l
================================================== ================================================== ==============
*** Active processes
wpa_supplicant:NO knetworkmanager:YES nm-applet:NO
================================================== ================================================== ==============
*** grep NETWORKMANAGER /etc/sysconfig/network/config
/bin/grep: /etc/sysconfig/network/config: No such file or directory
================================================== ================================================== ==============
*** grep -i persistent /etc/sysconfig/network/config
/bin/grep: /etc/sysconfig/network/config: No such file or directory
================================================== ================================================== ==============
*** grep 'eth|ath|wlan|ra' /etc/udev/rules.d/*net_persistent* /etc/udev/rules.d/70-persistent-net
/bin/egrep: /etc/udev/rules.d/*net_persistent*: No such file or directory
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:19:db:6a:e0:14", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:1e:2a:3d:e1:9a", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"
================================================== ================================================== ==============
*** grep -r 'eth[0-10]|ath[0-10]|wlan[0-10]|ra[0-10]' /etc/modprobe.*
================================================== ================================================== ==============
*** iwlist scanning
ESSID:"SMC"
Quality:60/100 Signal level:-57 dBm Noise level:-96 dBm
Encryption key:on
IE: WPA Version 1
================================================== ================================================== ==============
*** NWEliza states
IF:eth0 IP: IM:1
IF:wlan0 IP: IM:2
DI:2 dI:1 NIC:1 cNiC:2:1 NI:2 cNI:2 DHCP:0 NIW:wlan0-1 NDIS:0 NIWL:0 KM:0 WLW: 0 AP:1


da steht jetzt doch schon ne ecke mehr drin *g*

[Rain_maker]

*** iwlist scanning
ESSID:"SMC"
Quality:60/100 Signal level:-57 dBm Noise level:-96 dBm
Encryption key:on
IE: WPA Version 1

Wenn das stimmt, dann kannst Du WEP-Keys eingeben, bis Du schwarz wirst, vor allem, wenn


*** Active processes
wpa_supplicant:NO knetworkmanager:YES nm-applet:NO
kein wpa_supplicant läuft.

[BehrBor]

ich habs mit unserm (ellenlangen) wep key versucht. und ich hab extra mal das wpa angemacht und es mit nem 12345asdfg key versucht.

beides ging leider nicht.
also wenn ihr mir jetzt sagt das ich einfach nur wpa_supplicant 12345asdfg eintippen muss und das geht wär ich echt glücklich ;)

[Rain_maker]

beides ging leider nicht.

Das ist leider keine Fehlerbeschreibung.


also wenn ihr mir jetzt sagt das ich einfach nur wpa_supplicant 12345asdfg eintippen muss und das geht wär ich echt glücklich ;)

Das Glücksgefühl wird noch auf sich warten lassen müssen.

- Bei der Konfiguration mittels NWM _explizit_ die WPA-Version angeben

- Statt NWM die klassische Methode ausprobieren

http://wiki.ubuntuusers.de/WLAN/wpa_supplicant

Notfalls zunächst von Hand versuchen die Verbindung mittels wpa_supplicant aufzubauen, siehe

http://wiki.ubuntuusers.de/WLAN/wpa_supplicant#wpa-supplicant-testen-manuell-starten

Greetz,

RM

[BehrBor]

hmm nee.. funktiniert nicht.
habs nach anleitung gemacht, aber bekomm keine verbindung zum router :(
ich paste hier einfach mal was ich jetzt gemacht habe, von anfang bis ende


root@sidd:/home/sidd/Desktop# wpa_passphrase SMC asdf1234

network={
ssid="SMC"
#psk="asdf1234"
psk=e6e998393b61125e3aef04ee82d53bfbfe22805223fa77 48e22b4fbfcd0b6e20
}

root@sidd:/home/sidd/Desktop# vi /etc/wpa_supplicant/wpa_supplicant.conf
root@sidd:/home/sidd/Desktop# vi /etc/wpa_supplicant/wpa_supplicant.conf
root@sidd:/home/sidd/Desktop# wpa_supplicant -i wlan0 -D wext -c /etc/wpa_supplicant/wpa_supplicant.conf -d

Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
eapol_version=1
ap_scan=1
Line 11: Invalid passphrase length 64 (expected: 8..63) 'e6e998393b61125e3aef04ee82d53bfbfe22805223fa7748e 22b4fbfcd0b6e20"'.
Line 11: failed to parse psk '"e6e998393b61125e3aef04ee82d53bfbfe22805223fa7748e2 2b4fbfcd0b6e20"'.
Line 12: WPA-PSK accepted for key management, but no PSK configured.
Line 12: failed to parse network block.
Failed to read or parse configuration '/etc/wpa_supplicant/wpa_supplicant.conf'.
Failed to add interface wlan0
Cancelling scan request
Cancelling authentication timeout

root@sidd:/home/sidd/Desktop# vi /etc/wpa_supplicant/wpa_supplicant.conf
root@sidd:/home/sidd/Desktop# wpa_supplicant -i wlan0 -D wext -c /etc/wpa_supplicant/wpa_supplicant.conf -d

Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
eapol_version=1
ap_scan=1
Priority group 0
id=0 ssid='SMC'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=18 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:1e:2a:3d:e1:9a
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=3):
53 4d 43 SMC
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 220 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
skip - no WPA/RSN IE
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 254 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=3):
53 4d 43 SMC
Scan timeout - try to get results
Received 254 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 254 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=3):
53 4d 43 SMC
Scan timeout - try to get results
Received 254 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 254 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=3):
53 4d 43 SMC
Scan timeout - try to get results
Received 254 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 254 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=3):
53 4d 43 SMC
Scan timeout - try to get results
Received 254 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 254 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=3):
53 4d 43 SMC
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface wlan0
State: SCANNING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_wext_set_wpa
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_countermeasures
No keys have been configured - skip key clearing
Cancelling scan request
Cancelling authentication timeout
WEXT: Operstate: linkmode=0, operstate=6

root@sidd:/home/sidd/Desktop# iwconfig

lo no wireless extensions.

eth0 no wireless extensions.

wlan0 IEEE 802.11g ESSID:off/any
Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated
Bit Rate:54 Mb/s Tx-Power:20 dBm Sensitivity=0/3
RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

root@sidd:/home/sidd/Desktop# wpa_supplicant -i wlan0 -D wext -c /etc/wpa_supplicant/wpa_supplicant.conf -dd

Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
eapol_version=1
ap_scan=1
Line: 4 - start of a new network block
ssid - hexdump_ascii(len=3):
53 4d 43 SMC
scan_ssid=1 (0x1)
proto: 0x1
key_mgmt: 0x2
pairwise: 0x8
group: 0x8
PSK (ASCII passphrase) - hexdump_ascii(len=8): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
id=0 ssid='SMC'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=18 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:1e:2a:3d:e1:9a
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=3):
53 4d 43 SMC
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 220 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
skip - no WPA/RSN IE
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 220 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
skip - no WPA/RSN IE
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=3):
53 4d 43 SMC
Scan timeout - try to get results
Received 254 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface wlan0
State: SCANNING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_wext_set_wpa
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_countermeasures
No keys have been configured - skip key clearing
Cancelling scan request
Cancelling authentication timeout
WEXT: Operstate: linkmode=0, operstate=6

root@sidd:/home/sidd/Desktop# vi /etc/wpa_supplicant/wpa_supplicant.conf

root@sidd:/home/sidd/Desktop# dhc
dhcdbd dhclient dhclient3 dhclient-script

root@sidd:/home/sidd/Desktop# dhclient

Internet Systems Consortium DHCP Client V3.0.6
Copyright 2004-2007 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

Listening on LPF/wlan0/00:1e:2a:3d:e1:9a
Sending on LPF/wlan0/00:1e:2a:3d:e1:9a
Listening on LPF/eth0/00:19:db:6a:e0:14
Sending on LPF/eth0/00:19:db:6a:e0:14
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 10
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6


root@sidd:/home/sidd/Desktop# dhclient wlan0

There is already a pid file /var/run/dhclient.pid with pid 134519072
Internet Systems Consortium DHCP Client V3.0.6
Copyright 2004-2007 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

Listening on LPF/wlan0/00:1e:2a:3d:e1:9a
Sending on LPF/wlan0/00:1e:2a:3d:e1:9a
Sending on Socket/fallback
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9

und meine conf sieht so aus


ctrl_interface=/var/run/wpa_supplicant
eapol_version=1
ap_scan=1
network={
ssid="SMC"
scan_ssid=1
proto=WPA
key_mgmt=WPA-PSK
pairwise=TKIP
group=TKIP
psk="beide keys ausprobiert. den langen und den kurzen"
}

[Rain_maker]

Line 11: Invalid passphrase length 64
(expected: 8..63) 'e6e998393b61125e3aef04ee82d53bfbfe22805223fa7748e 22b4fbfcd0b6e20"'.

Aber da

a) Ubuntu

b) ndiswrapper

geb ich an die Kunterbuntu-experten weiter, keine Ahnung, was da wieder schief läuft, die "" sollten jedenfalls nur bei ASCII-Passphrasen gesetzt werden.

Ansonsten spackt vielleicht der Router rum oder der Windowstreiber macht Zicken.

Greetz,

RM

[BehrBor]

ja daraufhin hab ich den key einfach so reingeschrieben, ohne ihn vorher durch wpa_passphrase laufen zu lassen.
hab den code oben mal (hoffentlich) lesbarer gemacht, indem ich vor meine eingaben eine leerzeile gemacht hab :D

[BehrBor]

hmm.. aber ich glaube das ist ein routerproblem. inzwischen ist nichtmal mehr eine verbindung mit der windowskofiguration zu bekommen. bzw eine verbindung schon, aber der router vergibt keine ip adressen mehr.

ich muss mich die tage mal hinsetzen und das dingen von grund auf neu konfigurieren.

[BehrBor]

so dann wollen wir das thema mal neu aufrollen *g*
ist n bisschen in vergessenheit geraten.. naja ich hoff das tut der ganzen sache keinen abbruch *g*

also ich hab die routerconfig wieder hergestellt.. login mit windows klappt wunderbar.. aber das jukt ja nicht.

ich glaub das der wpa_supplicant n problem mit dem router hat.
iwlist scanning gibt folgendes aus:


bla bla .. router mac und signalstärken..
und jetzt wirds interessant:
IE: WPA Version 1
Group Cipher: WEP-104 (hää?!?)
pairwise cipher (1): TKIP
Authentication suites (1): PSK


also mein verdacht ist, das ubuntu diese 2 unterschiedlichen verschlüsselungen (WEP und WPA) nicht hinbekommt.
ich glaub ich werd mal mit meinen mitbewohnern sprechen.. also entweder wpa oder wep.. aber beides macht ja nun wirklich keinen sinn

aber back to topic:
kann es sein das linux das unter umständen nicht auf die reihe bekommt?

[Grothesk]

Kann sein.
Und oben war irgendwo der key zu lang. Statt 64 Zeichen maximal 63 Zeichen nehmen.

[BehrBor]

neues notebook neuer versuch ;-)



xds@bngl337:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 04)
00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 (rev 04)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4)
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 04)
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 04)
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 04)
00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 04)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04)
05:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
05:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03)
05:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05)
05:04.0 CardBus bridge: ENE Technology Inc CB-712/4 Cardbus Controller (rev 10)
05:04.1 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller (rev 01)
05:04.2 SD Host controller: ENE Technology Inc ENE PCI Secure Digital Card Reader Controller (rev 01)
05:04.3 FLASH memory: ENE Technology Inc FLASH memory: ENE Technology Inc: (rev 01)
05:04.4 FLASH memory: ENE Technology Inc SD/MMC Card Reader Controller (rev 01)


xds@bngl337:~$ iwlist scanning
lo Interface doesn't support scanning.

eth0 Interface doesn't support scanning.

eth1 Scan completed :
Cell 01 - Address: 00:04:E2:8B:22:7A
ESSID:"SMC"
Protocol:IEEE 802.11bg
Mode:Master
Frequency:2.437 GHz (Channel 6)
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Quality=87/100 Signal level=-42 dBm
IE: WPA Version 1
Group Cipher : WEP-104
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
Extra: Last beacon: 140ms ago


xds@bngl337:~$ sudo vi /etc/wpa_supplicant/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant
eapol_version=1
ap_scan=1
network={
ssid="SMC"
scan_ssid=1
proto=WPA
pairwise=TKIP
group=TKIP
psk=e69db40c6af45a79ef4ef0d65da1668e1ddf8337dddc58 2396959fb8ab6c3222
}

xds@bngl337:~$ sudo wpa_supplicant -i eth1 -D wext -c /etc/wpa_supplicant/wpa_supplicant.conf -d
Initializing interface 'eth1' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
eapol_version=1
ap_scan=1
Priority group 0
id=0 ssid='SMC'
Initializing interface (2) 'eth1'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=18 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:13:ce:9f:3c:e4
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
Added interface eth1
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=3):
53 4d 43 SMC
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 251 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 251 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:04:e2:8b:22:7a
State: SCANNING -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=00:04:e2:8b:22:7a
No keys have been configured - skip key clearing
Network configuration found for the current AP
WPA: No WPA/RSN IE available from association info
WPA: Set cipher suites based on configuration
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 3 proto 1
WPA: clearing AP WPA IE
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT 802.1X
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 01
EAPOL: External notification - portControl=Auto
Associated with 00:04:e2:8b:22:7a
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
EAPOL: startWhen --> 0
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
Authentication with 00:04:e2:8b:22:7a timed out.
Added BSSID 00:04:e2:8b:22:7a into blacklist
wpa_driver_wext_disassociate
No keys have been configured - skip key clearing
State: ASSOCIATED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=3):
53 4d 43 SMC
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Added BSSID 00:00:00:00:00:00 into blacklist
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
State: SCANNING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 251 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No APs found - clear blacklist and try again
Removed BSSID 00:00:00:00:00:00 from blacklist (clear)
Removed BSSID 00:04:e2:8b:22:7a from blacklist (clear)
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 251 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 251 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 251 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 251 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip WPA IE - GTK cipher mismatch
Try to find non-WPA AP
0: 00:04:e2:8b:22:7a ssid='SMC' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
EAPOL: startWhen --> 0
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface eth1
State: DISCONNECTED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_wext_set_wpa
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_countermeasures
No keys have been configured - skip key clearing
Cancelling scan request
Cancelling authentication timeout
WEXT: Operstate: linkmode=0, operstate=6


aber der gleiche *******.. naja am montag werd ich die WPA verschlüsselung kicken und einfach das netzwerk hiden..
dann gibbet auch im allg. weniger probs (hoff ich :D)

[BehrBor]

soooo.. updates *g*
also linux kommt nicht mit der doppelverschlüsselung zurecht (im gegensatz zu windows *grml* )
das ist scheinbar ein allg. Linuxproblem .. kann man nichts machen :(
aber das ganze hat natürlich auch was gute.. jetzt ist unser netz wenigstens sicher.. WEP verschlüsselung ausgestellt und netzwerk hidden.. dazu noch n honeypot aufgemacht an dem ein nichtssagender rechner hängt *g*