krisal-x
13.08.08, 13:26
Hallo an alle Linux Spezies,,,
Ich habe vor enige zeit versucht meine T-Sinus 111 Card auf meinem Laptop lauffähig zu bekommen ohne erfolg. das betriebssystem war openSUSE 10.3...
jetzt habe ich openSUSE 11 2.6.25.11-0.1 installiert und auf den befehl hwinfo --wlan bekomme ich folgende meldung:
15: PCMCIA 00.0: 0282 WLAN controller
[Created at pcmcia.84]
UDI: /org/freedesktop/Hal/devices/pcmcia__1__1
Unique ID: oUbz.Y1gSBQ8wLT9
Parent ID: lgGW.WkcP9CLR9wA
SysFS ID: /devices/pci0000:00/0000:00:0c.0/0.0
SysFS BusID: 0.0
Hardware Class: network
Model: "T-Sinus 111card"
Hotplug: CardBus
Socket: 0
Vendor: pcmcia 0x01bf "T-Sinus"
Device: pcmcia 0x3301 "111card"
Driver: "hostap_cs"
Driver Modules: "hostap_cs"
Device File: wlan0
Features: WLAN
WLAN encryption modes: WEP40 WEP104 TKIP CCMP
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "pcmcia:m01BFc3301f06fn00pfn00pa8C389DC1pb6A23AC17p c00000000pd92B9EFFB"
Driver Info #0:
Driver Status: hostap_cs is active
Driver Activation Cmd: "modprobe hostap_cs"
Extra Info: T-Sinus, 111card, 2.0.0
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #2 (CardBus bridge)
anschließend habe ich den Befehl: modprobe hostap_cs ausgefürt und anschließend noch iwconfig eingegeben...
das ergebnis war auf iwconfig:
lo no wireless extensions.
eth0 no wireless extensions.
wifi0 IEEE 802.11-DS Mode:Managed
Encryption key: off
wlan0 IEEE 802.11-DS Mode:Managed
Encryption key: off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
so jetzt meine frage währe, wie muss ich weiter verfahren damit das Wlanmodul funktioniert???
für hilfe währe ich dankbar...
MFG Krisztian...
Ich habe vor enige zeit versucht meine T-Sinus 111 Card auf meinem Laptop lauffähig zu bekommen ohne erfolg. das betriebssystem war openSUSE 10.3...
jetzt habe ich openSUSE 11 2.6.25.11-0.1 installiert und auf den befehl hwinfo --wlan bekomme ich folgende meldung:
15: PCMCIA 00.0: 0282 WLAN controller
[Created at pcmcia.84]
UDI: /org/freedesktop/Hal/devices/pcmcia__1__1
Unique ID: oUbz.Y1gSBQ8wLT9
Parent ID: lgGW.WkcP9CLR9wA
SysFS ID: /devices/pci0000:00/0000:00:0c.0/0.0
SysFS BusID: 0.0
Hardware Class: network
Model: "T-Sinus 111card"
Hotplug: CardBus
Socket: 0
Vendor: pcmcia 0x01bf "T-Sinus"
Device: pcmcia 0x3301 "111card"
Driver: "hostap_cs"
Driver Modules: "hostap_cs"
Device File: wlan0
Features: WLAN
WLAN encryption modes: WEP40 WEP104 TKIP CCMP
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "pcmcia:m01BFc3301f06fn00pfn00pa8C389DC1pb6A23AC17p c00000000pd92B9EFFB"
Driver Info #0:
Driver Status: hostap_cs is active
Driver Activation Cmd: "modprobe hostap_cs"
Extra Info: T-Sinus, 111card, 2.0.0
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #2 (CardBus bridge)
anschließend habe ich den Befehl: modprobe hostap_cs ausgefürt und anschließend noch iwconfig eingegeben...
das ergebnis war auf iwconfig:
lo no wireless extensions.
eth0 no wireless extensions.
wifi0 IEEE 802.11-DS Mode:Managed
Encryption key: off
wlan0 IEEE 802.11-DS Mode:Managed
Encryption key: off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
so jetzt meine frage währe, wie muss ich weiter verfahren damit das Wlanmodul funktioniert???
für hilfe währe ich dankbar...
MFG Krisztian...