RAW-JAW
10.07.08, 22:25
Hallo liebe Community.
Wenn ich mein Sony Ericsson K550i an den Rechner anschließe, zeigt dmesg folgendes:
hub 1-0:1.0: unable to enumerate USB device on port 2
usb 2-2: new full speed USB device using uhci_hcd and address 3
usb 2-2: device not accepting address 3, error -71
hub 2-0:1.0: unable to enumerate USB device on port 2
hub 1-0:1.0: unable to enumerate USB device on port 2
usb 2-2: new full speed USB device using uhci_hcd and address 5
usb 2-2: configuration #2 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi1 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi 1:0:0:0: Direct-Access Sony Eri Memory Stick 0000 PQ: 0 ANSI: 0
usb-storage: device scan complete
scsi 0:0:0:0: Direct-Access Sony Eri Memory Stick 0000 PQ: 0 ANSI: 0
usb-storage: device scan complete
Driver 'sd' needs updating - please use bus_type methods
sd 1:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: [sdb] Attached SCSI removable disk
sd 1:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: Attached scsi generic sg1 type 0
usb 2-2: USB disconnect, address 5
hub 1-0:1.0: unable to enumerate USB device on port 2
usb 2-2: new full speed USB device using uhci_hcd and address 6
usb 2-2: configuration #2 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
scsi 2:0:0:0: Direct-Access Sony Eri Memory Stick 0000 PQ: 0 ANSI: 0
sd 2:0:0:0: [sda] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
scsi 3:0:0:0: Direct-Access Sony Eri Memory Stick 0000 PQ: 0 ANSI: 0
sd 3:0:0:0: [sdb] Attached SCSI removable disk
sd 3:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
Die Laufwerke (Phone und Memoystick) werden also erkannt.
wenn ich nun fdisk /dev/sdb ausführe und dort p eingebe, sehe ich auf einmal die Partition:
Platte /dev/sdb: 2045 MByte, 2045579776 Byte
128 Köpfe, 32 Sektoren/Spuren, 975 Zylinder
Einheiten = Zylinder von 4096 × 512 = 2097152 Bytes
Disk identifier: 0x00000000
Gerät boot. Anfang Ende Blöcke Id System
/dev/sdb1 * 1 976 1997636+ 6 FAT16
Partition 1 hat unterschiedliche phys./log. Enden:
phys=(975, 127, 32) logisch=(975, 63, 32)
Danach steht in dmesg folgendes:
sd 3:0:0:0: [sdb] 3995273 512-byte hardware sectors (2046 MB)
sd 3:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sd 3:0:0:0: [sdb] 3995273 512-byte hardware sectors (2046 MB)
sd 3:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sdb: p1 exceeds device capacity
attempt to access beyond end of device
sdb: rw=0, want=3995512, limit=3995273
Buffer I/O error on device sdb1, logical block 3995136
attempt to access beyond end of device
sdb: rw=0, want=3995513, limit=3995273
Buffer I/O error on device sdb1, logical block 3995137
attempt to access beyond end of device
sdb: rw=0, want=3995514, limit=3995273
wobei von diesen "attempt to access beyond end of device"-Meldungen recht viele kommen. Ich kann aber auf das Handy zugreifen.
Hat jemand eine Idee, warum ich immer erst fdisk starten muss, um an die Daten auf dem Handy zu kommen? Das macht das ganze recht unkomfortabel, ich hätte es gerne per automount eingebunden wie meine USB-Platten und die Digicam auch...
Vielen Dank schonmal,
raw
Wenn ich mein Sony Ericsson K550i an den Rechner anschließe, zeigt dmesg folgendes:
hub 1-0:1.0: unable to enumerate USB device on port 2
usb 2-2: new full speed USB device using uhci_hcd and address 3
usb 2-2: device not accepting address 3, error -71
hub 2-0:1.0: unable to enumerate USB device on port 2
hub 1-0:1.0: unable to enumerate USB device on port 2
usb 2-2: new full speed USB device using uhci_hcd and address 5
usb 2-2: configuration #2 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi1 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi 1:0:0:0: Direct-Access Sony Eri Memory Stick 0000 PQ: 0 ANSI: 0
usb-storage: device scan complete
scsi 0:0:0:0: Direct-Access Sony Eri Memory Stick 0000 PQ: 0 ANSI: 0
usb-storage: device scan complete
Driver 'sd' needs updating - please use bus_type methods
sd 1:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: [sdb] Attached SCSI removable disk
sd 1:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: Attached scsi generic sg1 type 0
usb 2-2: USB disconnect, address 5
hub 1-0:1.0: unable to enumerate USB device on port 2
usb 2-2: new full speed USB device using uhci_hcd and address 6
usb 2-2: configuration #2 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
scsi 2:0:0:0: Direct-Access Sony Eri Memory Stick 0000 PQ: 0 ANSI: 0
sd 2:0:0:0: [sda] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
scsi 3:0:0:0: Direct-Access Sony Eri Memory Stick 0000 PQ: 0 ANSI: 0
sd 3:0:0:0: [sdb] Attached SCSI removable disk
sd 3:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
Die Laufwerke (Phone und Memoystick) werden also erkannt.
wenn ich nun fdisk /dev/sdb ausführe und dort p eingebe, sehe ich auf einmal die Partition:
Platte /dev/sdb: 2045 MByte, 2045579776 Byte
128 Köpfe, 32 Sektoren/Spuren, 975 Zylinder
Einheiten = Zylinder von 4096 × 512 = 2097152 Bytes
Disk identifier: 0x00000000
Gerät boot. Anfang Ende Blöcke Id System
/dev/sdb1 * 1 976 1997636+ 6 FAT16
Partition 1 hat unterschiedliche phys./log. Enden:
phys=(975, 127, 32) logisch=(975, 63, 32)
Danach steht in dmesg folgendes:
sd 3:0:0:0: [sdb] 3995273 512-byte hardware sectors (2046 MB)
sd 3:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sd 3:0:0:0: [sdb] 3995273 512-byte hardware sectors (2046 MB)
sd 3:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sdb: p1 exceeds device capacity
attempt to access beyond end of device
sdb: rw=0, want=3995512, limit=3995273
Buffer I/O error on device sdb1, logical block 3995136
attempt to access beyond end of device
sdb: rw=0, want=3995513, limit=3995273
Buffer I/O error on device sdb1, logical block 3995137
attempt to access beyond end of device
sdb: rw=0, want=3995514, limit=3995273
wobei von diesen "attempt to access beyond end of device"-Meldungen recht viele kommen. Ich kann aber auf das Handy zugreifen.
Hat jemand eine Idee, warum ich immer erst fdisk starten muss, um an die Daten auf dem Handy zu kommen? Das macht das ganze recht unkomfortabel, ich hätte es gerne per automount eingebunden wie meine USB-Platten und die Digicam auch...
Vielen Dank schonmal,
raw