zara
22.02.08, 20:58
Hallo allerseits,
was ich mit dem Titel sagen möchte: meine Wlan Karte funktioniert - aber nur halb.
Stark simplifiziert: Ich kann empfangen, aber mich nicht einbuchen.
Das OS ist Suse 10.2 die Karte ist eine pcmcia "Senao NL-2011CD" (wird aber auch als "Intersil" bezeichnet und hat einen Prism2 Chipsatz (orinoco_CS))
Starte ich "kismet" funktioniert die Karte. Ich sehe mein Wlan - und die Netze der Nachbarschaft. Das ist aber leider schon alles. Außer kismet habe ich noch niemand sonst zur Zusammenarbeit bewegen können. Ich kann mich in kein Netz einbuchen. Um erstmal alle sonstigen Schwierigkeiten, die man so haben kann, auszuschließen, habe ich mein Netz vollkommen offen. Keine Verschlüsselung und nichts versteckt. Wenn ich im "knetworkmanager" die SSID angebe und verbinden lasse, geht die Anzeige nicht über 28% hinaus. ("Gerätekonfiguration") Auch blinkt die LED die ganze Zeit - egal was ich auch tue - außer: kismet läuft. Dann leuchtet die LED dauernd (und dann geht das Ding auch)
Das passiert bei meinem Suse-Notebook genauso wie beim Debian-Notebook
die Ausgabe von "iwconfig"
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11b ESSID:"" Nickname:"Prism I"
Mode:Managed Frequency:2.412 GHz Access Point: None
Bit Rate:2 Mb/s Sensitivity:1/3
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=0/92 Signal level=134/153 Noise level=134/153
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
sit0 no wireless extensions.
die Ausgabe von "dmesg"
Linux version 2.6.18.2-34-default (geeko@buildhost) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #1 SMP Mon Nov 27 11:46:27 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001dfd0000 (usable)
BIOS-e820: 000000001dfd0000 - 000000001dff0c00 (reserved)
BIOS-e820: 000000001dff0c00 - 000000001dffc000 (ACPI NVS)
BIOS-e820: 000000001dffc000 - 000000001e000000 (reserved)
0MB HIGHMEM available.
479MB LOWMEM available.
On node 0 totalpages: 122832
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 118736 pages, LIFO batch:31
DMI 2.3 present.
Using APIC driver default
IO/L-APIC allowed because system is MP or new enough
ACPI: RSDP (v000 COMPAQ ) @ 0x000f6ae0
ACPI: RSDT (v001 COMPAQ CPQ005A 0x15040420 CPQ 0x00000001) @ 0x1dff0c84
ACPI: FADT (v002 COMPAQ CPQ005A 0x00000002 CPQ 0x00000001) @ 0x1dff0c00
ACPI: SSDT (v001 COMPAQ CPQGysr 0x00001001 MSFT 0x0100000e) @ 0x1dff620e
ACPI: DSDT (v001 COMPAQ EVON800 0x00010000 MSFT 0x0100000e) @ 0x00000000
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x1008
Allocating PCI resources starting at 20000000 (gap: 1e000000:e2000000)
Detected 1592.128 MHz processor.
Built 1 zonelists. Total pages: 122832
Kernel command line: root=/dev/hda2 vga=0x314 resume=/dev/hda5 splash=silent showopts
bootsplash: silent mode.
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (013ca000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 480040k/491328k available (1697k kernel code, 10724k reserved, 968k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3186.26 BogoMIPS (lpj=6372532)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
checking if image is initramfs... it is
Freeing initrd memory: 3151k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0c20)
CPU0: Intel(R) Pentium(R) M processor 1600MHz stepping 05
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
HP Compaq Laptop series board detected. Selecting BIOS-method for reboots.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [C045] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.C045] bus is 0
PCI quirk: region 1000-103f claimed by ali7101 ACPI
PCI quirk: region 1100-111f claimed by ali7101 SMB
Boot video device is 0000:01:05.0
ACPI: PCI Interrupt Routing Table [\_SB_.C045._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C045.C046._PRT]
ACPI: Embedded Controller [C0E6] (gpe 24) interrupt mode.
ACPI: Power Resource [C15B] (on)
ACPI: Power Resource [C160] (on)
ACPI: Power Resource [C16A] (on)
ACPI: Power Resource [C17B] (on)
ACPI: PCI Interrupt Link [C0C5] (IRQs 5 *10 11)
ACPI: PCI Interrupt Link [C0C6] (IRQs 5 *10 11)
ACPI: PCI Interrupt Link [C0C7] (IRQs 5 10 *11)
ACPI: PCI Interrupt Link [C0C8] (IRQs 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C0C9] (IRQs 5 *10 11)
ACPI: PCI Interrupt Link [C0CA] (IRQs *5 10 11)
ACPI: PCI Interrupt Link [C0CB] (IRQs 5 10 *11)
ACPI: PCI Interrupt Link [C0CC] (IRQs 5 10 *11)
ACPI: Power Resource [C1E9] (off)
ACPI: Power Resource [C1EA] (off)
ACPI: Power Resource [C1EB] (off)
ACPI: Power Resource [C1EC] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:0c: ioport range 0x1000-0x107f could not be reserved
pnp: 00:0c: ioport range 0x1100-0x111f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 2000-2fff
MEM window: 90000000-900fffff
PREFETCH window: 94000000-97ffffff
PCI: Bus 2, cardbus bridge: 0000:00:0b.0
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bus 6, cardbus bridge: 0000:00:0b.1
IO window: 00003c00-00003cff
IO window: 00004000-000040ff
PREFETCH window: 24000000-25ffffff
MEM window: 26000000-27ffffff
ACPI: PCI Interrupt Link [C0C7] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [C0C7] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt 0000:00:0b.1[A] -> Link [C0C7] -> GSI 11 (level, low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1203715595.856:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Activating ISA DMA hang workarounds.
vesafb: framebuffer at 0x94000000, mapped to 0xde880000, using 3750k, total 32704k
vesafb: mode is 800x600x16, linelength=1600, pages=33
vesafb: protected mode interface info at c000:5143
vesafb: pmi: set display start = c00c51d7, set palette = c00c5223
vesafb: pmi: ports = 2010 2016 2054 2038 203c 205c 2000 2004 20b0 20b2 20b4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 82985 bytes,<6>...found (800x600, 49016 bytes, v3).
Console: switching to colour frame buffer device 96x33
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [C0CB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [C0CB] -> GSI 11 (level, low) -> IRQ 11
0000:00:08.0: ttyS1 at I/O 0x3428 (irq = 11) is a 8250
0000:00:08.0: ttyS3 at I/O 0x3440 (irq = 11) is a 8250
Couldn't register serial port 0000:00:08.0: -28
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:C178,PNP0f13:C179] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 1
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 196k freed
input: AT Translated Set 2 keyboard as /class/input/input1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: Invalid PBLK length [7]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
ACPI: Thermal Zone [TZ1] (43 C)
ACPI: Thermal Zone [TZ2] (48 C)
Time: acpi_pm clocksource has been installed.
ACPI: read EC, IB not empty
ACPI: read EC, OB not full
ACPI Exception (evregion-0424): AE_TIME, Returned by Handler for [EmbeddedControl] [20060707]
ACPI Exception (dswexec-0458): AE_TIME, While resolving operands for [OpcodeName unavailable] [20060707]
ACPI Error (psparse-0537): Method parse/execution failed [\_TZ_.C1E7] (Node ddfb0554), AE_TIME
ACPI Error (psparse-0537): Method parse/execution failed [\_TZ_.TZ3_._TMP] (Node ddfb0964), AE_TIME
ALI15X3: IDE controller at PCI slot 0000:00:10.0
ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [C0C5] -> GSI 10 (level, low) -> IRQ 10
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x3800-0x3807, BIOS settings: hda:DMA, hdb:pio
ALI15X3: simplex device: DMA forced
ide1: BM-DMA at 0x3808-0x380f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x1b6eb1, caps: 0xa84793/0x100000
serio: Synaptics pass-through port at isa0060/serio4/input0
hda: FUJITSU MHT2040AH, ATA DISK drive
input: SynPS/2 Synaptics TouchPad as /class/input/input2
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
Probing IDE interface ide1...
ACPI: Transitioning device [C1ED] to D3
ACPI: Transitioning device [C1ED] to D3
ACPI: Fan [C1ED] (off)
ACPI: Transitioning device [C1EE] to D3
ACPI: Transitioning device [C1EE] to D3
ACPI: Fan [C1EE] (off)
ACPI: Transitioning device [C1EF] to D3
ACPI: Transitioning device [C1EF] to D3
ACPI: Fan [C1EF] (off)
ACPI: Transitioning device [C1F0] to D3
ACPI: Transitioning device [C1F0] to D3
ACPI: Fan [C1F0] (off)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
lp0: using parport0 (interrupt-driven).
input: PS/2 Generic Mouse as /class/input/input3
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected Ati IGP345M chipset
agpgart: AGP aperture is 64M @ 0x9c000000
usbcore: registered new driver usbfs
tg3.c:v3.65 (August 07, 2006)
ACPI: PCI Interrupt Link [C0C9] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [C0C9] -> GSI 10 (level, low) -> IRQ 10
eth0: Tigon3 [partno(BCM5705mA1) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:08:02:e7:61:fc
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
usbcore: registered new driver hub
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Yenta: CardBus bridge found at 0000:00:0b.0 [0e11:005a]
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: enabling read prefetch/write burst
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000810
Yenta: CardBus bridge found at 0000:00:0b.1 [0e11:005a]
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000006
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt Link [C0C6] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [C0C6] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:12.0: OHCI Host Controller
ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:12.0: irq 10, io mem 0x98380000
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.18.2-34-default ohci_hcd
usb usb1: SerialNumber: 0000:00:12.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:12.1[B] -> Link [C0C6] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:12.1: OHCI Host Controller
ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:12.1: irq 10, io mem 0x98400000
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.18.2-34-default ohci_hcd
usb usb2: SerialNumber: 0000:00:12.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:12.2[C] -> Link [C0C6] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:12.2: EHCI Host Controller
ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 3
pccard: PCMCIA card inserted into slot 0
ehci_hcd 0000:00:12.2: irq 10, io mem 0x98480000
ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: EHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.18.2-34-default ehci_hcd
usb usb3: SerialNumber: 0000:00:12.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 5 ports detected
ACPI: PCI Interrupt Link [C0CC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [C0CC] -> GSI 11 (level, low) -> IRQ 11
cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f
cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f
cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia: registering new device pcmcia0.0
orinoco 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
orinoco_cs 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
eth1: Hardware identity 8003:0000:0001:0000
eth1: Station identity 001f:0003:0000:0008
eth1: Firmware determined as Intersil 0.8.3
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:02:6F:01:BD:20
eth1: Station name "Prism I"
eth1: ready
eth1: orinoco_cs at 0.0, irq 3, io 0x0100-0x013f
ieee80211_crypt: registered algorithm 'NULL'
hostap_cs: 0.4.4-kernel (Jouni Malinen <jkmaline@cc.hut.fi>)
ALSA sound/pci/ac97/ac97_codec.c:1923: AC'97 1 does not respond - RESET
ALSA sound/pci/ac97/ac97_codec.c:1932: AC'97 1 access is not valid [0xffffffff], removing mixer.
ALSA sound/pci/ali5451/ali5451.c:1977: ali mixer 1 creating error.
Adding 1052216k swap on /dev/hda5. Priority:-1 extents:1 across:1052216k
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
loop: loaded (max 8 devices)
AppArmor: AppArmor initialized
audit(1203715616.196:2): AppArmor initialized
bootsplash: status on console 0 changed to on
USB Universal Host Controller Interface driver v3.0
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on loop0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
bootsplash: status on console 0 changed to on
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (3838 buckets, 30704 max) - 228 bytes per conntrack
ACPI: AC Adapter [C138] (on-line)
ACPI: Battery Slot [C13A] (battery present)
ACPI: Battery Slot [C139] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [C13C]
ACPI: Lid Switch [C13B]
audit(1203712106.670:3): audit_pid=2941 old=0 by auid=4294967295
IA-32 Microcode Update Driver: v1.14a <tigran@veritas.com>
microcode: CPU0 updated from revision 0x5 to 0x7, date = 11092004
ADDRCONF(NETDEV_UP): eth1: link is not ready
eth1: New link status: Disconnected (0002)
PM: Writing back config space on device 0000:00:13.0 at offset b (was 165d14e4, writing 5a0e11)
PM: Writing back config space on device 0000:00:13.0 at offset 3 (was 0, writing 4010)
PM: Writing back config space on device 0000:00:13.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:00:13.0 at offset 1 (was 2b00000, writing 2b00006)
ADDRCONF(NETDEV_UP): eth0: link is not ready
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
NET: Registered protocol family 17
bootsplash: status on console 0 changed to on
eth0: no IPv6 routers present
eth0: no IPv6 routers present
ADDRCONF(NETDEV_UP): eth1: link is not ready
eth1: New link status: Disconnected (0002)
eth0: no IPv6 routers present
ADDRCONF(NETDEV_UP): eth1: link is not ready
eth1: New link status: Disconnected (0002)
ADDRCONF(NETDEV_UP): eth1: link is not ready
"eth1: link is not ready" klingt möchtig verdöchtig - und ich wäre wahrscheinlich sehr glücklich, wenn mir jemand verraten könnte, wie man den "link ready" macht ;)
gruesse
zara
was ich mit dem Titel sagen möchte: meine Wlan Karte funktioniert - aber nur halb.
Stark simplifiziert: Ich kann empfangen, aber mich nicht einbuchen.
Das OS ist Suse 10.2 die Karte ist eine pcmcia "Senao NL-2011CD" (wird aber auch als "Intersil" bezeichnet und hat einen Prism2 Chipsatz (orinoco_CS))
Starte ich "kismet" funktioniert die Karte. Ich sehe mein Wlan - und die Netze der Nachbarschaft. Das ist aber leider schon alles. Außer kismet habe ich noch niemand sonst zur Zusammenarbeit bewegen können. Ich kann mich in kein Netz einbuchen. Um erstmal alle sonstigen Schwierigkeiten, die man so haben kann, auszuschließen, habe ich mein Netz vollkommen offen. Keine Verschlüsselung und nichts versteckt. Wenn ich im "knetworkmanager" die SSID angebe und verbinden lasse, geht die Anzeige nicht über 28% hinaus. ("Gerätekonfiguration") Auch blinkt die LED die ganze Zeit - egal was ich auch tue - außer: kismet läuft. Dann leuchtet die LED dauernd (und dann geht das Ding auch)
Das passiert bei meinem Suse-Notebook genauso wie beim Debian-Notebook
die Ausgabe von "iwconfig"
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11b ESSID:"" Nickname:"Prism I"
Mode:Managed Frequency:2.412 GHz Access Point: None
Bit Rate:2 Mb/s Sensitivity:1/3
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=0/92 Signal level=134/153 Noise level=134/153
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
sit0 no wireless extensions.
die Ausgabe von "dmesg"
Linux version 2.6.18.2-34-default (geeko@buildhost) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #1 SMP Mon Nov 27 11:46:27 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001dfd0000 (usable)
BIOS-e820: 000000001dfd0000 - 000000001dff0c00 (reserved)
BIOS-e820: 000000001dff0c00 - 000000001dffc000 (ACPI NVS)
BIOS-e820: 000000001dffc000 - 000000001e000000 (reserved)
0MB HIGHMEM available.
479MB LOWMEM available.
On node 0 totalpages: 122832
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 118736 pages, LIFO batch:31
DMI 2.3 present.
Using APIC driver default
IO/L-APIC allowed because system is MP or new enough
ACPI: RSDP (v000 COMPAQ ) @ 0x000f6ae0
ACPI: RSDT (v001 COMPAQ CPQ005A 0x15040420 CPQ 0x00000001) @ 0x1dff0c84
ACPI: FADT (v002 COMPAQ CPQ005A 0x00000002 CPQ 0x00000001) @ 0x1dff0c00
ACPI: SSDT (v001 COMPAQ CPQGysr 0x00001001 MSFT 0x0100000e) @ 0x1dff620e
ACPI: DSDT (v001 COMPAQ EVON800 0x00010000 MSFT 0x0100000e) @ 0x00000000
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x1008
Allocating PCI resources starting at 20000000 (gap: 1e000000:e2000000)
Detected 1592.128 MHz processor.
Built 1 zonelists. Total pages: 122832
Kernel command line: root=/dev/hda2 vga=0x314 resume=/dev/hda5 splash=silent showopts
bootsplash: silent mode.
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (013ca000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 480040k/491328k available (1697k kernel code, 10724k reserved, 968k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3186.26 BogoMIPS (lpj=6372532)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
checking if image is initramfs... it is
Freeing initrd memory: 3151k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0c20)
CPU0: Intel(R) Pentium(R) M processor 1600MHz stepping 05
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
HP Compaq Laptop series board detected. Selecting BIOS-method for reboots.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [C045] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.C045] bus is 0
PCI quirk: region 1000-103f claimed by ali7101 ACPI
PCI quirk: region 1100-111f claimed by ali7101 SMB
Boot video device is 0000:01:05.0
ACPI: PCI Interrupt Routing Table [\_SB_.C045._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C045.C046._PRT]
ACPI: Embedded Controller [C0E6] (gpe 24) interrupt mode.
ACPI: Power Resource [C15B] (on)
ACPI: Power Resource [C160] (on)
ACPI: Power Resource [C16A] (on)
ACPI: Power Resource [C17B] (on)
ACPI: PCI Interrupt Link [C0C5] (IRQs 5 *10 11)
ACPI: PCI Interrupt Link [C0C6] (IRQs 5 *10 11)
ACPI: PCI Interrupt Link [C0C7] (IRQs 5 10 *11)
ACPI: PCI Interrupt Link [C0C8] (IRQs 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C0C9] (IRQs 5 *10 11)
ACPI: PCI Interrupt Link [C0CA] (IRQs *5 10 11)
ACPI: PCI Interrupt Link [C0CB] (IRQs 5 10 *11)
ACPI: PCI Interrupt Link [C0CC] (IRQs 5 10 *11)
ACPI: Power Resource [C1E9] (off)
ACPI: Power Resource [C1EA] (off)
ACPI: Power Resource [C1EB] (off)
ACPI: Power Resource [C1EC] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:0c: ioport range 0x1000-0x107f could not be reserved
pnp: 00:0c: ioport range 0x1100-0x111f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 2000-2fff
MEM window: 90000000-900fffff
PREFETCH window: 94000000-97ffffff
PCI: Bus 2, cardbus bridge: 0000:00:0b.0
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bus 6, cardbus bridge: 0000:00:0b.1
IO window: 00003c00-00003cff
IO window: 00004000-000040ff
PREFETCH window: 24000000-25ffffff
MEM window: 26000000-27ffffff
ACPI: PCI Interrupt Link [C0C7] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [C0C7] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt 0000:00:0b.1[A] -> Link [C0C7] -> GSI 11 (level, low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1203715595.856:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Activating ISA DMA hang workarounds.
vesafb: framebuffer at 0x94000000, mapped to 0xde880000, using 3750k, total 32704k
vesafb: mode is 800x600x16, linelength=1600, pages=33
vesafb: protected mode interface info at c000:5143
vesafb: pmi: set display start = c00c51d7, set palette = c00c5223
vesafb: pmi: ports = 2010 2016 2054 2038 203c 205c 2000 2004 20b0 20b2 20b4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 82985 bytes,<6>...found (800x600, 49016 bytes, v3).
Console: switching to colour frame buffer device 96x33
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [C0CB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [C0CB] -> GSI 11 (level, low) -> IRQ 11
0000:00:08.0: ttyS1 at I/O 0x3428 (irq = 11) is a 8250
0000:00:08.0: ttyS3 at I/O 0x3440 (irq = 11) is a 8250
Couldn't register serial port 0000:00:08.0: -28
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:C178,PNP0f13:C179] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 1
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 196k freed
input: AT Translated Set 2 keyboard as /class/input/input1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: Invalid PBLK length [7]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
ACPI: Thermal Zone [TZ1] (43 C)
ACPI: Thermal Zone [TZ2] (48 C)
Time: acpi_pm clocksource has been installed.
ACPI: read EC, IB not empty
ACPI: read EC, OB not full
ACPI Exception (evregion-0424): AE_TIME, Returned by Handler for [EmbeddedControl] [20060707]
ACPI Exception (dswexec-0458): AE_TIME, While resolving operands for [OpcodeName unavailable] [20060707]
ACPI Error (psparse-0537): Method parse/execution failed [\_TZ_.C1E7] (Node ddfb0554), AE_TIME
ACPI Error (psparse-0537): Method parse/execution failed [\_TZ_.TZ3_._TMP] (Node ddfb0964), AE_TIME
ALI15X3: IDE controller at PCI slot 0000:00:10.0
ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [C0C5] -> GSI 10 (level, low) -> IRQ 10
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x3800-0x3807, BIOS settings: hda:DMA, hdb:pio
ALI15X3: simplex device: DMA forced
ide1: BM-DMA at 0x3808-0x380f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x1b6eb1, caps: 0xa84793/0x100000
serio: Synaptics pass-through port at isa0060/serio4/input0
hda: FUJITSU MHT2040AH, ATA DISK drive
input: SynPS/2 Synaptics TouchPad as /class/input/input2
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
Probing IDE interface ide1...
ACPI: Transitioning device [C1ED] to D3
ACPI: Transitioning device [C1ED] to D3
ACPI: Fan [C1ED] (off)
ACPI: Transitioning device [C1EE] to D3
ACPI: Transitioning device [C1EE] to D3
ACPI: Fan [C1EE] (off)
ACPI: Transitioning device [C1EF] to D3
ACPI: Transitioning device [C1EF] to D3
ACPI: Fan [C1EF] (off)
ACPI: Transitioning device [C1F0] to D3
ACPI: Transitioning device [C1F0] to D3
ACPI: Fan [C1F0] (off)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
lp0: using parport0 (interrupt-driven).
input: PS/2 Generic Mouse as /class/input/input3
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected Ati IGP345M chipset
agpgart: AGP aperture is 64M @ 0x9c000000
usbcore: registered new driver usbfs
tg3.c:v3.65 (August 07, 2006)
ACPI: PCI Interrupt Link [C0C9] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [C0C9] -> GSI 10 (level, low) -> IRQ 10
eth0: Tigon3 [partno(BCM5705mA1) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:08:02:e7:61:fc
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
usbcore: registered new driver hub
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Yenta: CardBus bridge found at 0000:00:0b.0 [0e11:005a]
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: enabling read prefetch/write burst
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000810
Yenta: CardBus bridge found at 0000:00:0b.1 [0e11:005a]
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000006
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt Link [C0C6] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [C0C6] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:12.0: OHCI Host Controller
ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:12.0: irq 10, io mem 0x98380000
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.18.2-34-default ohci_hcd
usb usb1: SerialNumber: 0000:00:12.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:12.1[B] -> Link [C0C6] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:12.1: OHCI Host Controller
ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:12.1: irq 10, io mem 0x98400000
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.18.2-34-default ohci_hcd
usb usb2: SerialNumber: 0000:00:12.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:12.2[C] -> Link [C0C6] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:12.2: EHCI Host Controller
ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 3
pccard: PCMCIA card inserted into slot 0
ehci_hcd 0000:00:12.2: irq 10, io mem 0x98480000
ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: EHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.18.2-34-default ehci_hcd
usb usb3: SerialNumber: 0000:00:12.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 5 ports detected
ACPI: PCI Interrupt Link [C0CC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [C0CC] -> GSI 11 (level, low) -> IRQ 11
cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f
cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f
cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia: registering new device pcmcia0.0
orinoco 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
orinoco_cs 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
eth1: Hardware identity 8003:0000:0001:0000
eth1: Station identity 001f:0003:0000:0008
eth1: Firmware determined as Intersil 0.8.3
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:02:6F:01:BD:20
eth1: Station name "Prism I"
eth1: ready
eth1: orinoco_cs at 0.0, irq 3, io 0x0100-0x013f
ieee80211_crypt: registered algorithm 'NULL'
hostap_cs: 0.4.4-kernel (Jouni Malinen <jkmaline@cc.hut.fi>)
ALSA sound/pci/ac97/ac97_codec.c:1923: AC'97 1 does not respond - RESET
ALSA sound/pci/ac97/ac97_codec.c:1932: AC'97 1 access is not valid [0xffffffff], removing mixer.
ALSA sound/pci/ali5451/ali5451.c:1977: ali mixer 1 creating error.
Adding 1052216k swap on /dev/hda5. Priority:-1 extents:1 across:1052216k
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
loop: loaded (max 8 devices)
AppArmor: AppArmor initialized
audit(1203715616.196:2): AppArmor initialized
bootsplash: status on console 0 changed to on
USB Universal Host Controller Interface driver v3.0
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on loop0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
bootsplash: status on console 0 changed to on
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (3838 buckets, 30704 max) - 228 bytes per conntrack
ACPI: AC Adapter [C138] (on-line)
ACPI: Battery Slot [C13A] (battery present)
ACPI: Battery Slot [C139] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [C13C]
ACPI: Lid Switch [C13B]
audit(1203712106.670:3): audit_pid=2941 old=0 by auid=4294967295
IA-32 Microcode Update Driver: v1.14a <tigran@veritas.com>
microcode: CPU0 updated from revision 0x5 to 0x7, date = 11092004
ADDRCONF(NETDEV_UP): eth1: link is not ready
eth1: New link status: Disconnected (0002)
PM: Writing back config space on device 0000:00:13.0 at offset b (was 165d14e4, writing 5a0e11)
PM: Writing back config space on device 0000:00:13.0 at offset 3 (was 0, writing 4010)
PM: Writing back config space on device 0000:00:13.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:00:13.0 at offset 1 (was 2b00000, writing 2b00006)
ADDRCONF(NETDEV_UP): eth0: link is not ready
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
NET: Registered protocol family 17
bootsplash: status on console 0 changed to on
eth0: no IPv6 routers present
eth0: no IPv6 routers present
ADDRCONF(NETDEV_UP): eth1: link is not ready
eth1: New link status: Disconnected (0002)
eth0: no IPv6 routers present
ADDRCONF(NETDEV_UP): eth1: link is not ready
eth1: New link status: Disconnected (0002)
ADDRCONF(NETDEV_UP): eth1: link is not ready
"eth1: link is not ready" klingt möchtig verdöchtig - und ich wäre wahrscheinlich sehr glücklich, wenn mir jemand verraten könnte, wie man den "link ready" macht ;)
gruesse
zara