metallex
22.02.08, 17:41
Ich versuche bereits seit mehreren Tagen Wake On LAN auf einem Shuttle SV25 (Board: FV25 mit VIA PN133T Chipsatz + VIA C3) zum laufen zu bekommen. Der Rechner soll aus dem Standby (S1) mit einem Magicpacket wieder aufgeweckt werden können (unter Windows funktioniert das Szenario). Leider sind alle meine Bemühungen unter Debian bisher gescheitert. Installiert ist ein Debian Etch mit Standardkernel (2.6.18-486). Neben der Onboard-Netzwerkkarte (Realtek 8139c) ist zusätzlich eine Realtek 8169 Gigabit-Netzwerkkarte mit verbaut. WOL funktioniert auf beiden Karten unter Windows einwandfrei.
Standby und Suspend to RAM funktionieren unter Debian soweit problemlos. Interessanterweise lässt sich das System nach dem "Weck-Versuch" mit einem Magicpacket aber auch nicht mehr per Tastatur aus dem Standby aufwecken.
# cat /proc/acpi/wakeup
SLPB S5 *enabled
PCI0 S5 enabled no-bus:pci0000:00
USB0 S3 disabled pci:0000:00:07.2
USB1 S3 disabled pci:0000:00:07.3
MODM S4 disabled
UAR1 S5 disabled pnp:00:07
# ethtool eth2
Settings for eth2:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000033 (51)
Link detected: yes
# lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
00:0b.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46)
00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
01:00.0 VGA compatible controller: S3 Inc. 86C380 [ProSavageDDR K4M266] (rev 02)
Im Bios aktiviert:
Power-On by PCI Card
Modem Ring Resume
Ich hoffe ihr könnt mir helfen!
Standby und Suspend to RAM funktionieren unter Debian soweit problemlos. Interessanterweise lässt sich das System nach dem "Weck-Versuch" mit einem Magicpacket aber auch nicht mehr per Tastatur aus dem Standby aufwecken.
# cat /proc/acpi/wakeup
SLPB S5 *enabled
PCI0 S5 enabled no-bus:pci0000:00
USB0 S3 disabled pci:0000:00:07.2
USB1 S3 disabled pci:0000:00:07.3
MODM S4 disabled
UAR1 S5 disabled pnp:00:07
# ethtool eth2
Settings for eth2:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000033 (51)
Link detected: yes
# lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
00:0b.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46)
00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
01:00.0 VGA compatible controller: S3 Inc. 86C380 [ProSavageDDR K4M266] (rev 02)
Im Bios aktiviert:
Power-On by PCI Card
Modem Ring Resume
Ich hoffe ihr könnt mir helfen!