D H
01.02.08, 13:08
Hallo!
Ich habe mir einen neuen Rechner gegönnt und musste jetzt feststellen, dass smartctl Fehler liefert, die ich nicht verstehe.
Soweit ich informiert bin, sind die Werte der einzelnen Parameter eigentlich in Ordnung.
Was mich verunsichert ist der ATA Error Count: 52 mit immer dem gleichen Fehler.
Generell treten keine Auffälligkeiten, wie Fehlermeldungen oder Abstürze auf. Die Selbsttests von smartctl brachten auch keine Fehler.
Ich konnte auch nicht rausfinden, dass sich der ATA Error count bei einem bestimmten Systemverhalten, oder sowas erhöht.
Ausgabe von smartctl -a /dev/sda
smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST3250410AS
Serial Number: 6RY3ESVB
Firmware Version: 3.AAC
User Capacity: 250.059.350.016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Feb 1 13:55:24 2008 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 64) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 110 100 006 Pre-fail Always - 28809318
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 29
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 063 060 030 Pre-fail Always - 2186103
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 59
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 29
187 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 065 060 045 Old_age Always - 588513315
194 Temperature_Celsius 0x0022 035 040 000 Old_age Always - 35 (Lifetime Min/Max 0/20)
195 Hardware_ECC_Recovered 0x001a 080 067 000 Old_age Always - 146689581
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 52 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 52 occurred at disk power-on lifetime: 57 hours (2 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 02:16:01.996 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 02:16:07.440 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 02:16:07.440 SET MAX ADDRESS EXT
27 00 01 2e 51 1c e0 00 02:16:07.316 READ NATIVE MAX ADDRESS EXT
37 00 01 2e 51 1c ed 00 02:16:07.316 SET MAX ADDRESS EXT
Error 51 occurred at disk power-on lifetime: 57 hours (2 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 02:16:01.996 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 02:16:01.996 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 02:16:01.996 SET MAX ADDRESS EXT
27 00 01 6f 59 1c e0 00 02:16:01.995 READ NATIVE MAX ADDRESS EXT
29 00 01 6f 59 1c e0 00 02:16:01.995 READ MULTIPLE EXT
Error 50 occurred at disk power-on lifetime: 53 hours (2 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 00:01:31.606 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 00:01:31.606 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 00:01:29.499 SET MAX ADDRESS EXT
27 00 01 2e 51 1c e0 00 00:01:29.499 READ NATIVE MAX ADDRESS EXT
37 00 01 2e 51 1c ed 00 00:01:29.375 SET MAX ADDRESS EXT
Error 49 occurred at disk power-on lifetime: 53 hours (2 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 00:01:26.285 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 00:01:26.284 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 00:01:29.499 SET MAX ADDRESS EXT
27 00 01 6f 59 1c e0 00 00:01:29.499 READ NATIVE MAX ADDRESS EXT
29 00 01 6f 59 1c e0 00 00:01:29.375 READ MULTIPLE EXT
Error 48 occurred at disk power-on lifetime: 51 hours (2 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 04:38:11.654 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 04:38:10.890 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 04:38:10.841 SET MAX ADDRESS EXT
27 00 01 2e 51 1c e0 00 04:38:10.840 READ NATIVE MAX ADDRESS EXT
37 00 01 2e 51 1c ed 00 04:38:10.840 SET MAX ADDRESS EXT
Error 49 occurred at disk power-on lifetime: 53 hours (2 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 00:01:26.285 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 00:01:26.284 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 00:01:29.499 SET MAX ADDRESS EXT
27 00 01 6f 59 1c e0 00 00:01:29.499 READ NATIVE MAX ADDRESS EXT
29 00 01 6f 59 1c e0 00 00:01:29.375 READ MULTIPLE EXT
Error 48 occurred at disk power-on lifetime: 51 hours (2 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 04:38:11.654 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 04:38:10.890 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 04:38:10.841 SET MAX ADDRESS EXT
27 00 01 2e 51 1c e0 00 04:38:10.840 READ NATIVE MAX ADDRESS EXT
37 00 01 2e 51 1c ed 00 04:38:10.840 SET MAX ADDRESS EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 19 -
# 2 Short offline Completed without error 00% 18 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Sind solche Fehler "normal", oder sollte ich die Platte besser umtauschen?
Was ist denn SET MAX ADDRESS EXT bzw. READ NATIVE MAX ADDRESS EXT?
Über sämtliche Hinweise oder Ideen würde ich mich sehr freuen!
Grüße,
D H
Ich habe mir einen neuen Rechner gegönnt und musste jetzt feststellen, dass smartctl Fehler liefert, die ich nicht verstehe.
Soweit ich informiert bin, sind die Werte der einzelnen Parameter eigentlich in Ordnung.
Was mich verunsichert ist der ATA Error Count: 52 mit immer dem gleichen Fehler.
Generell treten keine Auffälligkeiten, wie Fehlermeldungen oder Abstürze auf. Die Selbsttests von smartctl brachten auch keine Fehler.
Ich konnte auch nicht rausfinden, dass sich der ATA Error count bei einem bestimmten Systemverhalten, oder sowas erhöht.
Ausgabe von smartctl -a /dev/sda
smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST3250410AS
Serial Number: 6RY3ESVB
Firmware Version: 3.AAC
User Capacity: 250.059.350.016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Feb 1 13:55:24 2008 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 64) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 110 100 006 Pre-fail Always - 28809318
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 29
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 063 060 030 Pre-fail Always - 2186103
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 59
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 29
187 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 065 060 045 Old_age Always - 588513315
194 Temperature_Celsius 0x0022 035 040 000 Old_age Always - 35 (Lifetime Min/Max 0/20)
195 Hardware_ECC_Recovered 0x001a 080 067 000 Old_age Always - 146689581
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 52 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 52 occurred at disk power-on lifetime: 57 hours (2 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 02:16:01.996 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 02:16:07.440 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 02:16:07.440 SET MAX ADDRESS EXT
27 00 01 2e 51 1c e0 00 02:16:07.316 READ NATIVE MAX ADDRESS EXT
37 00 01 2e 51 1c ed 00 02:16:07.316 SET MAX ADDRESS EXT
Error 51 occurred at disk power-on lifetime: 57 hours (2 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 02:16:01.996 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 02:16:01.996 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 02:16:01.996 SET MAX ADDRESS EXT
27 00 01 6f 59 1c e0 00 02:16:01.995 READ NATIVE MAX ADDRESS EXT
29 00 01 6f 59 1c e0 00 02:16:01.995 READ MULTIPLE EXT
Error 50 occurred at disk power-on lifetime: 53 hours (2 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 00:01:31.606 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 00:01:31.606 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 00:01:29.499 SET MAX ADDRESS EXT
27 00 01 2e 51 1c e0 00 00:01:29.499 READ NATIVE MAX ADDRESS EXT
37 00 01 2e 51 1c ed 00 00:01:29.375 SET MAX ADDRESS EXT
Error 49 occurred at disk power-on lifetime: 53 hours (2 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 00:01:26.285 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 00:01:26.284 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 00:01:29.499 SET MAX ADDRESS EXT
27 00 01 6f 59 1c e0 00 00:01:29.499 READ NATIVE MAX ADDRESS EXT
29 00 01 6f 59 1c e0 00 00:01:29.375 READ MULTIPLE EXT
Error 48 occurred at disk power-on lifetime: 51 hours (2 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 04:38:11.654 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 04:38:10.890 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 04:38:10.841 SET MAX ADDRESS EXT
27 00 01 2e 51 1c e0 00 04:38:10.840 READ NATIVE MAX ADDRESS EXT
37 00 01 2e 51 1c ed 00 04:38:10.840 SET MAX ADDRESS EXT
Error 49 occurred at disk power-on lifetime: 53 hours (2 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 00:01:26.285 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 00:01:26.284 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 00:01:29.499 SET MAX ADDRESS EXT
27 00 01 6f 59 1c e0 00 00:01:29.499 READ NATIVE MAX ADDRESS EXT
29 00 01 6f 59 1c e0 00 00:01:29.375 READ MULTIPLE EXT
Error 48 occurred at disk power-on lifetime: 51 hours (2 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 2e 51 1c ed
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 2e 51 1c ed 00 04:38:11.654 SET MAX ADDRESS EXT
27 00 00 2e 51 1c e0 00 04:38:10.890 READ NATIVE MAX ADDRESS EXT
37 00 00 2e 51 1c ed 00 04:38:10.841 SET MAX ADDRESS EXT
27 00 01 2e 51 1c e0 00 04:38:10.840 READ NATIVE MAX ADDRESS EXT
37 00 01 2e 51 1c ed 00 04:38:10.840 SET MAX ADDRESS EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 19 -
# 2 Short offline Completed without error 00% 18 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Sind solche Fehler "normal", oder sollte ich die Platte besser umtauschen?
Was ist denn SET MAX ADDRESS EXT bzw. READ NATIVE MAX ADDRESS EXT?
Über sämtliche Hinweise oder Ideen würde ich mich sehr freuen!
Grüße,
D H