pass
13.11.07, 19:34
Hallo,
ich habe Suse 10.3 und Virtualbox aus dem RPM aus der Innotek Seite installiert.
Ich habe dann das Bridging gemäss dem Howto aus diesem Forum installiert, jedoch ohne Erfolg. Unter Linux funzt Internet, jedoch unter dem Gastwindows nicht.
Hier ein Auszug aus meiner boot.msg
Listening on LPF/br0/00:50:70:f1:20:cd
Sending on LPF/br0/00:50:70:f1:20:cd
Sending on Socket/fallback
DHCPREQUEST on br0 to 255.255.255.255 port 67
DHCPREQUEST on br0 to 255.255.255.255 port 67
DHCPREQUEST on br0 to 255.255.255.255 port 67
DHCPDISCOVER on br0 to 255.255.255.255 port 67 interval 3
DHCPOFFER from 192.168.1.2
DHCPREQUEST on br0 to 255.255.255.255 port 67
DHCPACK from 192.168.1.2
bound to 192.168.1.37 -- renewal in 1459 seconds.
VirtualBox host networking interface creation utility, version 1.5.2
(C) 2005-2007 innotek GmbH
All rights reserved.
Creating the permanent host networking interface "vbox0" for user enz.
done<notice>killproc: kill(1015,3)
und dann später:
Setting up network interfaces:
lo
lo IP address: 127.0.0.1/8
Checking for network time protocol daemon (NTPD): unused
done br0
br0 Startmode is '�\200\231auto�\200\231'
skipped eth0 device: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
eth0 Startmode is 'off'
skipped vbox0
No configuration found for vbox0
unusedSetting up service network . . . . . . . . . . . . . . . .done
Hier meine eth0:
BOOTPROTO='dhcp'
# BOOTPROTO='static'
BROADCAST=''
ETHTOOL_OPTIONS=''
IPADDR=''
# IPADDR='0.0.0.0'
MTU=''
NAME='Realtek RT8139'
NETMASK='255.255.255.0'
NETWORK=''
REMOTE_IPADDR=''
STARTMODE='off'
UNIQUE='rBUF.IQxIdIhhuH7'
USERCONTROL='no'
_nm_name='bus-pci-0000:02:07.0'
und die boot.local:
brctl addbr br0
ifconfig eth0 0.0.0.0
brctl addif br0 eth0
dhclient br0
VBoxAddIF vbox0 enz br0
Was habe ich falsch gemacht?
Danke
Pascal
ich habe Suse 10.3 und Virtualbox aus dem RPM aus der Innotek Seite installiert.
Ich habe dann das Bridging gemäss dem Howto aus diesem Forum installiert, jedoch ohne Erfolg. Unter Linux funzt Internet, jedoch unter dem Gastwindows nicht.
Hier ein Auszug aus meiner boot.msg
Listening on LPF/br0/00:50:70:f1:20:cd
Sending on LPF/br0/00:50:70:f1:20:cd
Sending on Socket/fallback
DHCPREQUEST on br0 to 255.255.255.255 port 67
DHCPREQUEST on br0 to 255.255.255.255 port 67
DHCPREQUEST on br0 to 255.255.255.255 port 67
DHCPDISCOVER on br0 to 255.255.255.255 port 67 interval 3
DHCPOFFER from 192.168.1.2
DHCPREQUEST on br0 to 255.255.255.255 port 67
DHCPACK from 192.168.1.2
bound to 192.168.1.37 -- renewal in 1459 seconds.
VirtualBox host networking interface creation utility, version 1.5.2
(C) 2005-2007 innotek GmbH
All rights reserved.
Creating the permanent host networking interface "vbox0" for user enz.
done<notice>killproc: kill(1015,3)
und dann später:
Setting up network interfaces:
lo
lo IP address: 127.0.0.1/8
Checking for network time protocol daemon (NTPD): unused
done br0
br0 Startmode is '�\200\231auto�\200\231'
skipped eth0 device: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
eth0 Startmode is 'off'
skipped vbox0
No configuration found for vbox0
unusedSetting up service network . . . . . . . . . . . . . . . .done
Hier meine eth0:
BOOTPROTO='dhcp'
# BOOTPROTO='static'
BROADCAST=''
ETHTOOL_OPTIONS=''
IPADDR=''
# IPADDR='0.0.0.0'
MTU=''
NAME='Realtek RT8139'
NETMASK='255.255.255.0'
NETWORK=''
REMOTE_IPADDR=''
STARTMODE='off'
UNIQUE='rBUF.IQxIdIhhuH7'
USERCONTROL='no'
_nm_name='bus-pci-0000:02:07.0'
und die boot.local:
brctl addbr br0
ifconfig eth0 0.0.0.0
brctl addif br0 eth0
dhclient br0
VBoxAddIF vbox0 enz br0
Was habe ich falsch gemacht?
Danke
Pascal