smog_at
07.10.07, 11:52
Hey @all,
ich versuche gerade meinen Raid Controller zum laufen zu bringen und scheitere kläglich, hoffe jemand von Euch kann mir dabei helfen.
Es handel sich um um den Raid Controller '00:08.0 RAID bus controller: Integrated Technology Express, Inc. IT/ITE8212 Dual channel ATA RAID controller (PCI version seems to be IT8212, embedded s... (rev 13)'
Als OS verwende ich Fedora 7.
dmesg liefert:
Linux version 2.6.22.9-91.fc7 (kojibuilder@xenbuilder1.fedora.redhat.com) (gcc version 4.1.2 20070502 (Red Hat 4.1.2-12)) #1 SMP Thu Sep 27 23:10:59 EDT 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000fb930
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 131056) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 131056
HighMem 131056 -> 131056
early_node_map[1] active PFN ranges
0: 0 -> 131056
On node 0 totalpages: 131056
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 991 pages used for memmap
Normal zone: 125969 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP 000FA9E0, 0014 (r0 AMI )
ACPI: RSDT 1FFF0000, 002C (r1 AMIINT VIA_K7 10 MSFT 97)
ACPI: FACP 1FFF0030, 0081 (r1 AMIINT VIA_K7 11 MSFT 97)
ACPI: DSDT 1FFF0120, 31BC (r1 VIA VIA_K7 1000 MSFT 100000D)
ACPI: FACS 1FFF8000, 0040
ACPI: APIC 1FFF00C0, 0054 (r1 AMIINT VIA_K7 9 MSFT 97)
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists. Total pages: 130033
Kernel command line: ro root=/dev/VolGroup00/LogVol00 nodmraid rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0791000 soft=c0771000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1533.199 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 511176k/524224k available (2108k kernel code, 12392k reserved, 1112k data, 260k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffc56000 - 0xfffff000 (3748 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
.init : 0xc072b000 - 0xc076c000 ( 260 kB)
.data : 0xc060f3a8 - 0xc0725504 (1112 kB)
.text : 0xc0400000 - 0xc060f3a8 (2108 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 3068.07 BogoMIPS (lpj=1534036)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: CLK_CTL MSR was 6003d22f. Reprogramming to 2003d22f
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f3ff c1c3fbff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20070126
CPU0: AMD Athlon(tm) XP 1800+ stepping 01
Total of 1 processors activated (3068.07 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=336 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=488 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=176 bytes
sizeof(task_struct)=1536 bytes
Time: 16:45:11 Date: 10/06/07
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by vt8235 PM
PCI quirk: region 0400-040f claimed by vt8235 SMB
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: dde00000-dfefffff
PREFETCH window: d9d00000-ddcfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3502k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1191689111.540:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 1C0E7986B75803D3
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
Boot video device is 0000:01:00.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU1] (supports 16 throttling states)
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Processor cpuid 681 not supported
Using IPI No-Shortcut mode
Magic number: 11:407:792
Freeing unused kernel memory: 260k freed
Write protecting the kernel read-only data: 858k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 16
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 16, io base 0x0000b800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 16
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 16, io base 0x0000bc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 16
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 16, io base 0x0000c000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 16
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 16, io mem 0xdffdef00
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
SCSI subsystem initialized
libata version 2.21 loaded.
pata_via 0000:00:11.1: version 0.3.1
ACPI: Unable to derive IRQ for device 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001fc00 irq 14
ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001fc08 irq 15
ata1.00: ATA-6: WDC WD800JB-00JJC0, 05.01C05, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA
ata1.00: configured for UDMA/100
ata2.00: ATAPI: LG DVD-ROM DRD-8160B, 1.01, max UDMA/33
ata2.01: ATAPI: PHILIPS CDRW1610A, 0.010000, max UDMA/33
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA WDC WD800JB-00JJ 05.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: CD-ROM LG DVD-ROM DRD8160B 1.01 PQ: 0 ANSI: 5
scsi 1:0:1:0: CD-ROM PHILIPS CDRW1610A 02A4 PQ: 0 ANSI: 5
pata_pdc2027x 0000:00:07.0: version 0.9
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 17
pata_pdc2027x 0000:00:07.0: PLL input clock 16658 kHz
scsi2 : pata_pdc2027x
scsi3 : pata_pdc2027x
ata3: PATA max UDMA/133 cmd 0xe08e17c0 ctl 0xe08e1fda bmdma 0xe08e1000 irq 17
ata4: PATA max UDMA/133 cmd 0xe08e15c0 ctl 0xe08e1dda bmdma 0xe08e1008 irq 17
ata3.00: ATA-7: SAMSUNG SP0802N, TK200-04, max UDMA/100
ata3.00: 156368016 sectors, multi 16: LBA48
ata3.01: ATA-7: ST3802110A, 3.AAJ, max UDMA/100
ata3.01: 156301488 sectors, multi 16: LBA48
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/100
ata4.00: ATA-7: SAMSUNG SP0802N, TK200-04, max UDMA/100
ata4.00: 156368016 sectors, multi 16: LBA48
ata4.01: ATA-7: ST3802110A, 3.AAJ, max UDMA/100
ata4.01: 156301488 sectors, multi 16: LBA48
ata4.00: configured for UDMA/100
ata4.01: configured for UDMA/100
scsi 2:0:0:0: Direct-Access ATA SAMSUNG SP0802N TK20 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdb] 156368016 512-byte hardware sectors (80060 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdb] 156368016 512-byte hardware sectors (80060 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 2:0:0:0: [sdb] Attached SCSI disk
scsi 2:0:1:0: Direct-Access ATA ST3802110A 3.AA PQ: 0 ANSI: 5
sd 2:0:1:0: [sdc] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:1:0: [sdc] Write Protect is off
sd 2:0:1:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:1:0: [sdc] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:1:0: [sdc] Write Protect is off
sd 2:0:1:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 2:0:1:0: [sdc] Attached SCSI disk
scsi 3:0:0:0: Direct-Access ATA SAMSUNG SP0802N TK20 PQ: 0 ANSI: 5
sd 3:0:0:0: [sdd] 156368016 512-byte hardware sectors (80060 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sdd] 156368016 512-byte hardware sectors (80060 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 3:0:0:0: [sdd] Attached SCSI disk
scsi 3:0:1:0: Direct-Access ATA ST3802110A 3.AA PQ: 0 ANSI: 5
sd 3:0:1:0: [sde] 156301488 512-byte hardware sectors (80026 MB)
sd 3:0:1:0: [sde] Write Protect is off
sd 3:0:1:0: [sde] Mode Sense: 00 3a 00 00
sd 3:0:1:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:1:0: [sde] 156301488 512-byte hardware sectors (80026 MB)
sd 3:0:1:0: [sde] Write Protect is off
sd 3:0:1:0: [sde] Mode Sense: 00 3a 00 00
sd 3:0:1:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
sd 3:0:1:0: [sde] Attached SCSI disk
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1191689121.459:2): selinux=0 auid=4294967295
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
scsi 1:0:1:0: Attached scsi generic sg2 type 5
sd 2:0:0:0: Attached scsi generic sg3 type 0
sd 2:0:1:0: Attached scsi generic sg4 type 0
sd 3:0:0:0: Attached scsi generic sg5 type 0
sd 3:0:1:0: Attached scsi generic sg6 type 0
sr0: scsi3-mmc drive: 0x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
natsemi dp8381x driver, version 2.1, Sept 11, 2006
originally by Donald Becker <becker>
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 18
natsemi eth0: NatSemi DP8381[56] at 0xdffdf000 (0000:00:06.0), 00:09:5b:04:43:eb, IRQ 18, port TP.
pata_it821x: controller in smart mode.
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:08.0 to 64
scsi4 : pata_it821x
scsi5 : pata_it821x
ata5: PATA max MWDMA2 cmd 0x0001d400 ctl 0x0001d002 bmdma 0x0001c400 irq 19
ata6: PATA max MWDMA2 cmd 0x0001cc00 ctl 0x0001c802 bmdma 0x0001c408 irq 19
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
parport_pc 00:09: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
ata5.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80)
ata5.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80)
ata5.00: limiting speed to UDMA7:PIO5
ata5.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80)
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 20
eth0: VIA Rhine II at 0xdffdee00, 00:10:dc:df:41:8c, IRQ 20.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:11.5 to 64
NET: Registered protocol family 23
No dock devices found.
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
ACPI: Sleep Button (CM) [SLPB]
md: md2 stopped.
md: bind<sdb1>
md: bind<sdd1>
md: raid1 personality registered for level 1
raid1: raid set md2 active with 2 out of 2 mirrors
md: md1 stopped.
md: bind<sdc1>
md: bind<sde1>
raid1: raid set md1 active with 2 out of 2 mirrors
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ReiserFS: md1: found reiserfs format "3.6" with standard journal
ReiserFS: md1: using ordered data mode
ReiserFS: md1: journal params: device md1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md1: checking transaction log (md1)
ReiserFS: md1: replayed 2 transactions in 0 seconds
ReiserFS: md1: Using r5 hash to sort names
ReiserFS: md2: found reiserfs format "3.6" with standard journal
ReiserFS: md2: using ordered data mode
ReiserFS: md2: journal params: device md2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md2: checking transaction log (md2)
ReiserFS: md2: replayed 2 transactions in 0 seconds
ReiserFS: md2: Using r5 hash to sort names
Adding 1048568k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:1048568k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth1: DSPCFG accepted after 0 usec.
eth1: link up.
eth1: Setting full-duplex based on negotiated link capability.
audit(1191689142.273:3): audit_pid=1961 old=0 by auid=4294967295
eth0: no IPv6 routers present
eth1: no IPv6 routers present
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
'lspci' liefert:
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
00:06.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller
00:07.0 RAID bus controller: Promise Technology, Inc. PDC20271 (FastTrak TX2000) (rev 03)
00:08.0 RAID bus controller: Integrated Technology Express, Inc. IT/ITE8212 Dual channel ATA RAID controller (PCI version seems to be IT8212, embedded s... (rev 13)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15)
'lshw' liefert:
*-storage:0
description: RAID bus controller
product: PDC20271 (FastTrak TX2000)
vendor: Promise Technology, Inc.
physical id: 7
bus info: pci@0000:00:07.0
logical name: scsi2
logical name: scsi3
version: 03
width: 32 bits
clock: 66MHz
capabilities: storage pm bus_master cap_list emulated
configuration: driver=pata_pdc2027x latency=32 maxlatency=18 mingnt=4 module=pata_pdc2027x
*-disk:0
description: ATA Disk
product: SAMSUNG SP0802N
physical id: 0
bus info: scsi@2:0.0.0
logical name: /dev/sdb
version: TK20
serial: S00JJ20X902479
size: 74GB
capabilities: partitioned partitioned:dos
configuration: ansiversion=5
*-volume
description: Linux filesystem partition
physical id: 1
bus info: scsi@2:0.0.0,1
logical name: /dev/sdb1
capacity: 74GB
capabilities: primary bootable
*-disk:1
description: ATA Disk
product: ST3802110A
vendor: Seagate
physical id: 1
bus info: scsi@2:0.1.0
logical name: /dev/sdc
version: 3.AA
serial: 4LR4PVVE
size: 74GB
capabilities: partitioned partitioned:dos
configuration: ansiversion=5
*-volume
description: Linux filesystem partition
physical id: 1
bus info: scsi@2:0.1.0,1
logical name: /dev/sdc1
capacity: 74GB
capabilities: primary bootable
*-disk:2
description: ATA Disk
product: SAMSUNG SP0802N
physical id: 2
bus info: scsi@3:0.0.0
logical name: /dev/sdd
version: TK20
serial: S00JJ20X902360
size: 74GB
capabilities: partitioned partitioned:dos
configuration: ansiversion=5
*-volume
description: Linux filesystem partition
physical id: 1
bus info: scsi@3:0.0.0,1
logical name: /dev/sdd1
capacity: 74GB
capabilities: primary bootable
*-disk:3
description: ATA Disk
product: ST3802110A
vendor: Seagate
physical id: 3
bus info: scsi@3:0.1.0
logical name: /dev/sde
version: 3.AA
serial: 4LR3EAS9
size: 74GB
capabilities: partitioned partitioned:dos
configuration: ansiversion=5
*-volume
description: Linux filesystem partition
physical id: 1
bus info: scsi@3:0.1.0,1
logical name: /dev/sde1
capacity: 74GB
capabilities: primary bootable
*-storage:1
description: RAID bus controller
product: IT/ITE8212 Dual channel ATA RAID controller (PCI version seems to be IT8212, embedded seems to be ITE8212)
vendor: Integrated Technology Express, Inc.
physical id: 8
bus info: pci@0000:00:08.0
version: 13
width: 32 bits
clock: 66MHz
capabilities: storage pm bus_master cap_list
configuration: driver=pata_it821x latency=64 maxlatency=8 mingnt=8 module=pata_it821x
'lsmod | grep ata' liefert:
pata_it821x 14917 0
pata_pdc2027x 14789 4
pata_via 15813 2
ata_generic 11589 0
libata 118321 4 pata_it821x,pata_pdc2027x,pata_via,ata_generic
scsi_mod 140749 4 sr_mod,sg,libata,sd_mod
Weiters dauert es merkwürdig lange beim System Start wo er bei folgendem Eintrag stehen bleibt:
Starting system message bus
Also ausser sda (OS-Platte) und sdb - sde (2x 1er Raid) habe ich keine Platten mehr.
Theoretisch müsste ich ja für das 3te Raid über den IT821x Raid Controller auch noch 1 oder 2 PLatten haben.
Bitte um hilfe und
vielen vielen Dank im Voraus
Lg NoRulez
ich versuche gerade meinen Raid Controller zum laufen zu bringen und scheitere kläglich, hoffe jemand von Euch kann mir dabei helfen.
Es handel sich um um den Raid Controller '00:08.0 RAID bus controller: Integrated Technology Express, Inc. IT/ITE8212 Dual channel ATA RAID controller (PCI version seems to be IT8212, embedded s... (rev 13)'
Als OS verwende ich Fedora 7.
dmesg liefert:
Linux version 2.6.22.9-91.fc7 (kojibuilder@xenbuilder1.fedora.redhat.com) (gcc version 4.1.2 20070502 (Red Hat 4.1.2-12)) #1 SMP Thu Sep 27 23:10:59 EDT 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000fb930
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 131056) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 131056
HighMem 131056 -> 131056
early_node_map[1] active PFN ranges
0: 0 -> 131056
On node 0 totalpages: 131056
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 991 pages used for memmap
Normal zone: 125969 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP 000FA9E0, 0014 (r0 AMI )
ACPI: RSDT 1FFF0000, 002C (r1 AMIINT VIA_K7 10 MSFT 97)
ACPI: FACP 1FFF0030, 0081 (r1 AMIINT VIA_K7 11 MSFT 97)
ACPI: DSDT 1FFF0120, 31BC (r1 VIA VIA_K7 1000 MSFT 100000D)
ACPI: FACS 1FFF8000, 0040
ACPI: APIC 1FFF00C0, 0054 (r1 AMIINT VIA_K7 9 MSFT 97)
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists. Total pages: 130033
Kernel command line: ro root=/dev/VolGroup00/LogVol00 nodmraid rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0791000 soft=c0771000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1533.199 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 511176k/524224k available (2108k kernel code, 12392k reserved, 1112k data, 260k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffc56000 - 0xfffff000 (3748 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
.init : 0xc072b000 - 0xc076c000 ( 260 kB)
.data : 0xc060f3a8 - 0xc0725504 (1112 kB)
.text : 0xc0400000 - 0xc060f3a8 (2108 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 3068.07 BogoMIPS (lpj=1534036)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: CLK_CTL MSR was 6003d22f. Reprogramming to 2003d22f
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f3ff c1c3fbff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20070126
CPU0: AMD Athlon(tm) XP 1800+ stepping 01
Total of 1 processors activated (3068.07 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=336 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=488 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=176 bytes
sizeof(task_struct)=1536 bytes
Time: 16:45:11 Date: 10/06/07
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by vt8235 PM
PCI quirk: region 0400-040f claimed by vt8235 SMB
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: dde00000-dfefffff
PREFETCH window: d9d00000-ddcfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3502k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1191689111.540:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 1C0E7986B75803D3
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
Boot video device is 0000:01:00.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU1] (supports 16 throttling states)
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Processor cpuid 681 not supported
Using IPI No-Shortcut mode
Magic number: 11:407:792
Freeing unused kernel memory: 260k freed
Write protecting the kernel read-only data: 858k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 16
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 16, io base 0x0000b800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 16
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 16, io base 0x0000bc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 16
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 16, io base 0x0000c000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 16
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 16, io mem 0xdffdef00
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
SCSI subsystem initialized
libata version 2.21 loaded.
pata_via 0000:00:11.1: version 0.3.1
ACPI: Unable to derive IRQ for device 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001fc00 irq 14
ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001fc08 irq 15
ata1.00: ATA-6: WDC WD800JB-00JJC0, 05.01C05, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA
ata1.00: configured for UDMA/100
ata2.00: ATAPI: LG DVD-ROM DRD-8160B, 1.01, max UDMA/33
ata2.01: ATAPI: PHILIPS CDRW1610A, 0.010000, max UDMA/33
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA WDC WD800JB-00JJ 05.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: CD-ROM LG DVD-ROM DRD8160B 1.01 PQ: 0 ANSI: 5
scsi 1:0:1:0: CD-ROM PHILIPS CDRW1610A 02A4 PQ: 0 ANSI: 5
pata_pdc2027x 0000:00:07.0: version 0.9
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 17
pata_pdc2027x 0000:00:07.0: PLL input clock 16658 kHz
scsi2 : pata_pdc2027x
scsi3 : pata_pdc2027x
ata3: PATA max UDMA/133 cmd 0xe08e17c0 ctl 0xe08e1fda bmdma 0xe08e1000 irq 17
ata4: PATA max UDMA/133 cmd 0xe08e15c0 ctl 0xe08e1dda bmdma 0xe08e1008 irq 17
ata3.00: ATA-7: SAMSUNG SP0802N, TK200-04, max UDMA/100
ata3.00: 156368016 sectors, multi 16: LBA48
ata3.01: ATA-7: ST3802110A, 3.AAJ, max UDMA/100
ata3.01: 156301488 sectors, multi 16: LBA48
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/100
ata4.00: ATA-7: SAMSUNG SP0802N, TK200-04, max UDMA/100
ata4.00: 156368016 sectors, multi 16: LBA48
ata4.01: ATA-7: ST3802110A, 3.AAJ, max UDMA/100
ata4.01: 156301488 sectors, multi 16: LBA48
ata4.00: configured for UDMA/100
ata4.01: configured for UDMA/100
scsi 2:0:0:0: Direct-Access ATA SAMSUNG SP0802N TK20 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdb] 156368016 512-byte hardware sectors (80060 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdb] 156368016 512-byte hardware sectors (80060 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 2:0:0:0: [sdb] Attached SCSI disk
scsi 2:0:1:0: Direct-Access ATA ST3802110A 3.AA PQ: 0 ANSI: 5
sd 2:0:1:0: [sdc] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:1:0: [sdc] Write Protect is off
sd 2:0:1:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:1:0: [sdc] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:1:0: [sdc] Write Protect is off
sd 2:0:1:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 2:0:1:0: [sdc] Attached SCSI disk
scsi 3:0:0:0: Direct-Access ATA SAMSUNG SP0802N TK20 PQ: 0 ANSI: 5
sd 3:0:0:0: [sdd] 156368016 512-byte hardware sectors (80060 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sdd] 156368016 512-byte hardware sectors (80060 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 3:0:0:0: [sdd] Attached SCSI disk
scsi 3:0:1:0: Direct-Access ATA ST3802110A 3.AA PQ: 0 ANSI: 5
sd 3:0:1:0: [sde] 156301488 512-byte hardware sectors (80026 MB)
sd 3:0:1:0: [sde] Write Protect is off
sd 3:0:1:0: [sde] Mode Sense: 00 3a 00 00
sd 3:0:1:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:1:0: [sde] 156301488 512-byte hardware sectors (80026 MB)
sd 3:0:1:0: [sde] Write Protect is off
sd 3:0:1:0: [sde] Mode Sense: 00 3a 00 00
sd 3:0:1:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
sd 3:0:1:0: [sde] Attached SCSI disk
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1191689121.459:2): selinux=0 auid=4294967295
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
scsi 1:0:1:0: Attached scsi generic sg2 type 5
sd 2:0:0:0: Attached scsi generic sg3 type 0
sd 2:0:1:0: Attached scsi generic sg4 type 0
sd 3:0:0:0: Attached scsi generic sg5 type 0
sd 3:0:1:0: Attached scsi generic sg6 type 0
sr0: scsi3-mmc drive: 0x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
natsemi dp8381x driver, version 2.1, Sept 11, 2006
originally by Donald Becker <becker>
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 18
natsemi eth0: NatSemi DP8381[56] at 0xdffdf000 (0000:00:06.0), 00:09:5b:04:43:eb, IRQ 18, port TP.
pata_it821x: controller in smart mode.
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:08.0 to 64
scsi4 : pata_it821x
scsi5 : pata_it821x
ata5: PATA max MWDMA2 cmd 0x0001d400 ctl 0x0001d002 bmdma 0x0001c400 irq 19
ata6: PATA max MWDMA2 cmd 0x0001cc00 ctl 0x0001c802 bmdma 0x0001c408 irq 19
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
parport_pc 00:09: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
ata5.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80)
ata5.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80)
ata5.00: limiting speed to UDMA7:PIO5
ata5.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80)
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 20
eth0: VIA Rhine II at 0xdffdee00, 00:10:dc:df:41:8c, IRQ 20.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:11.5 to 64
NET: Registered protocol family 23
No dock devices found.
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
ACPI: Sleep Button (CM) [SLPB]
md: md2 stopped.
md: bind<sdb1>
md: bind<sdd1>
md: raid1 personality registered for level 1
raid1: raid set md2 active with 2 out of 2 mirrors
md: md1 stopped.
md: bind<sdc1>
md: bind<sde1>
raid1: raid set md1 active with 2 out of 2 mirrors
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ReiserFS: md1: found reiserfs format "3.6" with standard journal
ReiserFS: md1: using ordered data mode
ReiserFS: md1: journal params: device md1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md1: checking transaction log (md1)
ReiserFS: md1: replayed 2 transactions in 0 seconds
ReiserFS: md1: Using r5 hash to sort names
ReiserFS: md2: found reiserfs format "3.6" with standard journal
ReiserFS: md2: using ordered data mode
ReiserFS: md2: journal params: device md2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md2: checking transaction log (md2)
ReiserFS: md2: replayed 2 transactions in 0 seconds
ReiserFS: md2: Using r5 hash to sort names
Adding 1048568k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:1048568k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth1: DSPCFG accepted after 0 usec.
eth1: link up.
eth1: Setting full-duplex based on negotiated link capability.
audit(1191689142.273:3): audit_pid=1961 old=0 by auid=4294967295
eth0: no IPv6 routers present
eth1: no IPv6 routers present
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
'lspci' liefert:
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
00:06.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller
00:07.0 RAID bus controller: Promise Technology, Inc. PDC20271 (FastTrak TX2000) (rev 03)
00:08.0 RAID bus controller: Integrated Technology Express, Inc. IT/ITE8212 Dual channel ATA RAID controller (PCI version seems to be IT8212, embedded s... (rev 13)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15)
'lshw' liefert:
*-storage:0
description: RAID bus controller
product: PDC20271 (FastTrak TX2000)
vendor: Promise Technology, Inc.
physical id: 7
bus info: pci@0000:00:07.0
logical name: scsi2
logical name: scsi3
version: 03
width: 32 bits
clock: 66MHz
capabilities: storage pm bus_master cap_list emulated
configuration: driver=pata_pdc2027x latency=32 maxlatency=18 mingnt=4 module=pata_pdc2027x
*-disk:0
description: ATA Disk
product: SAMSUNG SP0802N
physical id: 0
bus info: scsi@2:0.0.0
logical name: /dev/sdb
version: TK20
serial: S00JJ20X902479
size: 74GB
capabilities: partitioned partitioned:dos
configuration: ansiversion=5
*-volume
description: Linux filesystem partition
physical id: 1
bus info: scsi@2:0.0.0,1
logical name: /dev/sdb1
capacity: 74GB
capabilities: primary bootable
*-disk:1
description: ATA Disk
product: ST3802110A
vendor: Seagate
physical id: 1
bus info: scsi@2:0.1.0
logical name: /dev/sdc
version: 3.AA
serial: 4LR4PVVE
size: 74GB
capabilities: partitioned partitioned:dos
configuration: ansiversion=5
*-volume
description: Linux filesystem partition
physical id: 1
bus info: scsi@2:0.1.0,1
logical name: /dev/sdc1
capacity: 74GB
capabilities: primary bootable
*-disk:2
description: ATA Disk
product: SAMSUNG SP0802N
physical id: 2
bus info: scsi@3:0.0.0
logical name: /dev/sdd
version: TK20
serial: S00JJ20X902360
size: 74GB
capabilities: partitioned partitioned:dos
configuration: ansiversion=5
*-volume
description: Linux filesystem partition
physical id: 1
bus info: scsi@3:0.0.0,1
logical name: /dev/sdd1
capacity: 74GB
capabilities: primary bootable
*-disk:3
description: ATA Disk
product: ST3802110A
vendor: Seagate
physical id: 3
bus info: scsi@3:0.1.0
logical name: /dev/sde
version: 3.AA
serial: 4LR3EAS9
size: 74GB
capabilities: partitioned partitioned:dos
configuration: ansiversion=5
*-volume
description: Linux filesystem partition
physical id: 1
bus info: scsi@3:0.1.0,1
logical name: /dev/sde1
capacity: 74GB
capabilities: primary bootable
*-storage:1
description: RAID bus controller
product: IT/ITE8212 Dual channel ATA RAID controller (PCI version seems to be IT8212, embedded seems to be ITE8212)
vendor: Integrated Technology Express, Inc.
physical id: 8
bus info: pci@0000:00:08.0
version: 13
width: 32 bits
clock: 66MHz
capabilities: storage pm bus_master cap_list
configuration: driver=pata_it821x latency=64 maxlatency=8 mingnt=8 module=pata_it821x
'lsmod | grep ata' liefert:
pata_it821x 14917 0
pata_pdc2027x 14789 4
pata_via 15813 2
ata_generic 11589 0
libata 118321 4 pata_it821x,pata_pdc2027x,pata_via,ata_generic
scsi_mod 140749 4 sr_mod,sg,libata,sd_mod
Weiters dauert es merkwürdig lange beim System Start wo er bei folgendem Eintrag stehen bleibt:
Starting system message bus
Also ausser sda (OS-Platte) und sdb - sde (2x 1er Raid) habe ich keine Platten mehr.
Theoretisch müsste ich ja für das 3te Raid über den IT821x Raid Controller auch noch 1 oder 2 PLatten haben.
Bitte um hilfe und
vielen vielen Dank im Voraus
Lg NoRulez