jm78
23.10.06, 01:10
Hi,
folgendes System: Notebook: Siemens Lifebook 2110, Turion 64, 512MB, Broadcom BCM4401-BO 100-Base-TX. ACPI ist an. Keine Lüfterprobleme und anderes wie sonst beschrieben.
System: Suse 10.1 Remastered, 32-bit, Linux version 2.6.16.13-4-default
Die Netzwerkkarte wurde bei der Installation über das Internet automtisch erkannt und funktionierte mit erwarteter Geschwindigkeit. Nach Abschuß der Installation liegt die Geschwindigkeit nur noch im unteren kb-Bereich und KNetworkManager meldet dauernd das er die Verbindug trennt und wieder herstellt, siehe auch /var/log/messages:
Oct 23 01:00:59 notebook-magerkurth kernel: b44: eth0: Link is down.
Oct 23 01:01:01 notebook-magerkurth kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Oct 23 01:01:01 notebook-magerkurth kernel: b44: eth0: Flow control is on for TX and on for RX.
Oct 23 01:01:01 notebook-magerkurth kernel: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Oct 23 01:01:01 notebook-magerkurth su: (to root) magerkurth on /dev/pts/1
Oct 23 01:01:02 notebook-magerkurth kernel: b44: eth0: Link is down.
Oct 23 01:01:04 notebook-magerkurth kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Oct 23 01:01:04 notebook-magerkurth kernel: b44: eth0: Flow control is on for TX and on for RX.
Oct 23 01:01:04 notebook-magerkurth kernel: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Oct 23 01:01:09 notebook-magerkurth kernel: b44: eth0: Link is down.
Oct 23 01:01:12 notebook-magerkurth kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Oct 23 01:01:12 notebook-magerkurth kernel: b44: eth0: Flow control is on for TX and on for RX.
Oct 23 01:01:12 notebook-magerkurth kernel: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Das ganze wurde bei einer rsync-Übertragung protokolliert. Ich hatte vorher 9.3 drauf , da wahr der selbe Fehler. Ich habe gehofft das der neuere Kernel von 10.1 das behebt.
Keine Ahnung wie ich jetzt verfahren soll. :ugly: :ugly: :ugly:
PS: 32-bit weil ich viele Wissentschaftliche Software benötige, die zum Teil auf 64-bit noch nicht so stabil läuft.
Grüße!!!
folgendes System: Notebook: Siemens Lifebook 2110, Turion 64, 512MB, Broadcom BCM4401-BO 100-Base-TX. ACPI ist an. Keine Lüfterprobleme und anderes wie sonst beschrieben.
System: Suse 10.1 Remastered, 32-bit, Linux version 2.6.16.13-4-default
Die Netzwerkkarte wurde bei der Installation über das Internet automtisch erkannt und funktionierte mit erwarteter Geschwindigkeit. Nach Abschuß der Installation liegt die Geschwindigkeit nur noch im unteren kb-Bereich und KNetworkManager meldet dauernd das er die Verbindug trennt und wieder herstellt, siehe auch /var/log/messages:
Oct 23 01:00:59 notebook-magerkurth kernel: b44: eth0: Link is down.
Oct 23 01:01:01 notebook-magerkurth kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Oct 23 01:01:01 notebook-magerkurth kernel: b44: eth0: Flow control is on for TX and on for RX.
Oct 23 01:01:01 notebook-magerkurth kernel: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Oct 23 01:01:01 notebook-magerkurth su: (to root) magerkurth on /dev/pts/1
Oct 23 01:01:02 notebook-magerkurth kernel: b44: eth0: Link is down.
Oct 23 01:01:04 notebook-magerkurth kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Oct 23 01:01:04 notebook-magerkurth kernel: b44: eth0: Flow control is on for TX and on for RX.
Oct 23 01:01:04 notebook-magerkurth kernel: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Oct 23 01:01:09 notebook-magerkurth kernel: b44: eth0: Link is down.
Oct 23 01:01:12 notebook-magerkurth kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Oct 23 01:01:12 notebook-magerkurth kernel: b44: eth0: Flow control is on for TX and on for RX.
Oct 23 01:01:12 notebook-magerkurth kernel: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Das ganze wurde bei einer rsync-Übertragung protokolliert. Ich hatte vorher 9.3 drauf , da wahr der selbe Fehler. Ich habe gehofft das der neuere Kernel von 10.1 das behebt.
Keine Ahnung wie ich jetzt verfahren soll. :ugly: :ugly: :ugly:
PS: 32-bit weil ich viele Wissentschaftliche Software benötige, die zum Teil auf 64-bit noch nicht so stabil läuft.
Grüße!!!