Mattlas
21.12.05, 17:16
Hallo!
Habe einen LG Xtick und Suse 10.0. Wenn ich den auf FAT formatierten Stick einstecke, wird er unter lsusb zwar angezeigt, doch nicht im Arbeitsplatz. dmesg sagt folgendes:
Habt ihr eine Idee?
usb 2-1: new full speed USB device using uhci_hcd and address 3
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
Vendor: LG Model: XTICK Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
sda: Unit Not Ready, sense:
: Current: sense key: Unit Attention
Additional sense: Not ready to ready change, medium may have changed
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
sd: Current: sense key: Unit Attention
Additional sense: Not ready to ready change, medium may have changed
sda: test WP failed, assume Write Enabled
sda: assuming drive cache: write through
sda: Unit Not Ready, sense:
: Current: sense key: Unit Attention
Additional sense: Not ready to ready change, medium may have changed
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda: sda1
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 0
usb-storage: device scan complete
Habe einen LG Xtick und Suse 10.0. Wenn ich den auf FAT formatierten Stick einstecke, wird er unter lsusb zwar angezeigt, doch nicht im Arbeitsplatz. dmesg sagt folgendes:
Habt ihr eine Idee?
usb 2-1: new full speed USB device using uhci_hcd and address 3
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
Vendor: LG Model: XTICK Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
sda: Unit Not Ready, sense:
: Current: sense key: Unit Attention
Additional sense: Not ready to ready change, medium may have changed
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
sd: Current: sense key: Unit Attention
Additional sense: Not ready to ready change, medium may have changed
sda: test WP failed, assume Write Enabled
sda: assuming drive cache: write through
sda: Unit Not Ready, sense:
: Current: sense key: Unit Attention
Additional sense: Not ready to ready change, medium may have changed
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda: sda1
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 0
usb-storage: device scan complete