Festplatte oder Mainbord kaputt?

[ThorstenK]

Hallo,

mein System spinnt seit einigen Tagen: Die Festplatten steigen während des Betriebs aus dem DMA-Modus aus, ich hab diverse Kernelversionen versucht (jedes Mal das Selbe), an der Software liegt es also wohl nicht. Jetzt stellt sich mir die Frage ob das Problem von der/den Platte(n) kommt oder vom Mainbord aus geht?!

Hier mal der Auszug aus der syslog
Oct 17 12:27:27 aspartat kernel: hdb: status error: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error }
Oct 17 12:27:27 aspartat kernel: hdb: status error: error=0x7f { DriveStatusError UncorrectableError SectorIdNotFound TrackZeroNotFound AddrMarkNotFound }, LBAsect=260013951, sector=51123983
Oct 17 12:27:27 aspartat kernel: ide: failed opcode was: unknown
Oct 17 12:27:27 aspartat kernel: hdb: drive not ready for command
Oct 17 12:27:37 aspartat kernel: ide0: reset: success

und hier die Meldung von dmesg
hdb: status error: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error }
hdb: status error: error=0x7f { DriveStatusError UncorrectableError SectorIdNotFound TrackZeroNotFound AddrMarkNotFound }, LBAsect=260013951, sector=51123983
ide: failed opcode was: unknown
hda: DMA disabled
hdb: DMA disabled
hdb: drive not ready for command
ide0: reset: success

Sieht doch schon irgendwie nach der Festplatte an /dev/hdb aus oder?? Was meint ihr ist die hin oder kann man da noch was machen??

Thorsten

[Tomek]

Kannst du bitte mal die Ausgabe von smartctl hier posten?

smartctl -a /dev/hdb
Du kannst auch deine Festplatte mit Hilfe von smartctl prüfen lassen:

smartctl -t long /dev/hdb
Während der Test läuft, kannst du ganz normal mit dem Rechner weiter arbeiten, solltest ihn aber nicht neustarten oder ausschalten.

[ThorstenK]

Hallo,

das ist die Ausgabe von smartctl -a /dev/hdb


smartctl version 5.33 [i686-pc-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model: Maxtor 6Y060L0
Serial Number: Y2RH0F7E
Firmware Version: YAR41VW0
User Capacity: 61,492,838,400 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Mon Oct 17 16:20:10 2005 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 34) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 181) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 33) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 252 252 063 Pre-fail Always - 587
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 5
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 251 250 187 Pre-fail Always - 52244
9 Power_On_Minutes 0x0032 229 229 000 Old_age Always - 788h+35m
10 Spin_Retry_Count 0x002b 252 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 252 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 251 251 000 Old_age Always - 1089
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 47
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 569
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 249 000 Old_age Always - 55
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 252 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 252 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 197 197 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0

SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2 occurred at disk power-on lifetime: 7602 hours (316 days + 18 hours)
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 e0 08 00:03:24.272 READ DMA
c6 00 10 00 00 00 e0 08 00:03:24.272 SET MULTIPLE MODE
91 00 3f 00 00 00 ef 08 00:03:24.272 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 e0 08 00:03:24.256 RECALIBRATE [OBS-4]
c8 00 01 00 00 00 e0 04 00:03:24.240 READ DMA

Error 1 occurred at disk power-on lifetime: 7602 hours (316 days + 18 hours)
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 e0 00 00:03:24.208 READ DMA
b0 d9 10 01 4f c2 a0 00 00:03:23.856 SMART DISABLE OPERATIONS
b0 da 10 01 4f c2 a0 00 00:03:23.840 SMART RETURN STATUS
b0 d8 10 01 4f c2 a0 00 00:03:23.776 SMART ENABLE OPERATIONS
c6 03 10 01 00 00 a0 00 00:03:23.776 SET MULTIPLE MODE

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Ich habe auch den Test gemacht.. leider weiss ich nicht wie ich die Resultate angezeigt bekomme?!

Thorsten

[Tomek]

Ich habe auch den Test gemacht.. leider weiss ich nicht wie ich die Resultate angezeigt bekomme?!
Das Testergebnis kannst du wieder mit smartctl -a /dev/hdb abrufen. Es wird am Schluss angezeigt, wenn der Test durchgelaufen ist.

[ThorstenK]

Ok,

hier ist das Testergebnis:
hast du schon ne Vermutung an was es liegen koennte??



smartctl version 5.33 [i686-pc-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model: Maxtor 6Y060L0
Serial Number: Y2RH0F7E
Firmware Version: YAR41VW0
User Capacity: 61,492,838,400 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Tue Oct 18 14:32:16 2005 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 181) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 33) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 252 252 063 Pre-fail Always - 763
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 7
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 251 250 187 Pre-fail Always - 65213
9 Power_On_Minutes 0x0032 229 229 000 Old_age Always - 800h+37m
10 Spin_Retry_Count 0x002b 252 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 252 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 251 251 000 Old_age Always - 1091
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 48
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 702
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 249 000 Old_age Always - 13
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 252 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 252 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 195 193 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0

SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2 occurred at disk power-on lifetime: 7602 hours (316 days + 18 hours)
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 e0 08 00:03:24.272 READ DMA
c6 00 10 00 00 00 e0 08 00:03:24.272 SET MULTIPLE MODE
91 00 3f 00 00 00 ef 08 00:03:24.272 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 e0 08 00:03:24.256 RECALIBRATE [OBS-4]
c8 00 01 00 00 00 e0 04 00:03:24.240 READ DMA

Error 1 occurred at disk power-on lifetime: 7602 hours (316 days + 18 hours)
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 e0 00 00:03:24.208 READ DMA
b0 d9 10 01 4f c2 a0 00 00:03:23.856 SMART DISABLE OPERATIONS
b0 da 10 01 4f c2 a0 00 00:03:23.840 SMART RETURN STATUS
b0 d8 10 01 4f c2 a0 00 00:03:23.776 SMART ENABLE OPERATIONS
c6 03 10 01 00 00 a0 00 00:03:23.776 SET MULTIPLE MODE

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 7915 -
# 2 Extended offline Completed without error 00% 7910 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

[Tomek]

Ich würde die Festplatte noch mit dem Tool des Festplattenherstellers prüfen und auch mal das Kabel austauschen.

[ThorstenK]

Hallo Tomek,

koenntest du mir die einzelnen Error-messages mal etwas erlautern?
Koennten die Fehler auf vom ide-controller kommen? Was denkst du? Der Maxtor Test erkennt leider die Festplatte(n) von mir nicht, keine Ahnung warum?!


smartctl -a /dev/hda
smartctl version 5.33 [i686-pc-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model: Maxtor 6Y120L0
Serial Number: Y35GKYAE
Firmware Version: YAR41BW0
User Capacity: 122,942,324,736 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Thu Oct 20 18:02:28 2005 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 242) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 54) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 205 205 063 Pre-fail Always - 4615
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 23
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 251 250 187 Pre-fail Always - 48183
9 Power_On_Minutes 0x0032 251 251 000 Old_age Always - 790h+01m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 252 252 000 Old_age Always - 488
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 39
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 5091
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 251 000 Old_age Always - 1
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 1
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 188 188 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0

SMART Error Log Version: 1
ATA Error Count: 4
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 4 occurred at disk power-on lifetime: 675 hours (28 days + 3 hours)
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 50 b6 2c e1 Error: ICRC, ABRT at LBA = 0x012cb650 = 19707472

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 50 b6 2c e1 08 00:06:09.408 READ DMA
c8 00 08 50 b6 28 e1 08 00:06:09.392 READ DMA
c8 00 08 50 b6 24 e1 08 00:06:09.392 READ DMA
c8 00 08 50 b6 20 e1 08 00:06:09.376 READ DMA
c8 00 08 50 b6 1c e1 08 00:06:09.376 READ DMA

Error 3 occurred at disk power-on lifetime: 651 hours (27 days + 3 hours)
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 48 55 54 e0 Error: ICRC, ABRT at LBA = 0x00545548 = 5526856

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 48 55 54 e0 08 00:10:11.056 READ DMA
c8 00 08 80 a1 54 e0 08 00:10:11.040 READ DMA
c8 00 08 b0 d1 30 e1 08 00:10:11.040 READ DMA
c8 00 08 50 e9 5a e0 08 00:10:11.040 READ DMA
c8 00 08 a8 d1 30 e1 08 00:10:11.040 READ DMA

Error 2 occurred at disk power-on lifetime: 29 hours (1 days + 5 hours)
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 f4 e0 63 e0 Error: ICRC, ABRT at LBA = 0x0063e0f4 = 6545652

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 f4 e0 63 e0 00 00:06:39.920 READ DMA
c8 00 01 f3 e0 63 e0 00 00:06:39.920 READ DMA
c8 00 01 f2 e0 63 e0 00 00:06:39.920 READ DMA
c8 00 01 f1 e0 63 e0 00 00:06:39.920 READ DMA
c8 00 01 23 b2 35 e0 00 00:06:39.920 READ DMA

Error 1 occurred at disk power-on lifetime: 28 hours (1 days + 4 hours)
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 f7 e0 63 e0 Error: ICRC, ABRT at LBA = 0x0063e0f7 = 6545655

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 f7 e0 63 e0 00 00:08:31.952 READ DMA
c8 00 01 f6 e0 63 e0 00 00:08:31.952 READ DMA
c8 00 01 f5 e0 63 e0 00 00:08:31.952 READ DMA
c8 00 01 f4 e0 63 e0 00 00:08:31.952 READ DMA
c8 00 01 f3 e0 63 e0 00 00:08:31.952 READ DMA

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 738 -
# 2 Extended offline Completed without error 00% 719 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.