Schnitz
21.04.05, 14:45
Hallo zusammen,
Ich habe eine Red Hat 9 Büchse mit einer Fritz Card und will yaps über /dev/ttyI0 einrichten. Das ganze _hat_ auch schon funktioniert. Jetzt hängt der ISDN Anschluss allerdings nicht mehr an einer TK Anlage sondern direkt an einem echten S0 Bus.
Wenn Ich versuche mich mit yaps einzuwählen passiert folgendes:
[root@nagios root]# yaps 0175XXXX test
Found service D1 for 0175XXXX
Sending following message:
0175XXXX (D1, 0175XXXX): test powered by XXX
Trying to open /dev/ttyI0 for modem standard
[Hangup]
[Send] <cr>
[Cmd Mdzz 200]
[Send] ATZ<cr>
[Expect] <cr>ATZ<cr><cr><lf>OK got OK
[Send] AT&E0<cr>
[Expect] <cr><lf>AT&E0<cr><cr><lf>OK got OK
Using modem standard at 38400 bps, 8n1 over /dev/ttyI0
Trying do dial 01712521001
[Send] ATD01712521001<cr>
[Expect] <cr><lf>ATD01712521001<cr><cr><lf>NO DIALTONE got NO DIALTONE
Unable to dial D1
In /etc/yaps.rc ist folgendes eingestellt (Auszüge):
device /dev/ttyI0
# habe ich auch schon mit der rufnummer ohne vorwahl anstatt der 0 probiert
init \\r !200D ATZ\r <OK AT&E0\r <OK
dial ATD%L\r <60CONNECT|OK|BUSY|NO\sDIALTONE|NO\sCARRIER
reset ATZ\r <OK
timeout 10
modems standard
speed 38400
bits-per-byte 8
parity none
stopbits 1
cv-default {
Ä [
Ö \
Ü ]
ä {
ö |
ü }
ß ~
}
cv-extend {
\l \s
\n \s
\r \s
\f \s
\t \s
}
lsmod erzeugt folgendes:
Module Size Used by Not tainted
hisax 549348 0 (unused)
isdn 137984 0 [hisax]
slhc 6740 0 [isdn]
kernelcapi 33792 0
capiutil 24864 0 [kernelcapi]
capifs 5420 0
nfs 81336 2 (autoclean)
lockd 58704 1 (autoclean) [nfs]
sunrpc 81564 1 (autoclean) [nfs lockd]
iptable_filter 2412 0 (autoclean) (unused)
ip_tables 15096 1 [iptable_filter]
autofs 13268 0 (autoclean) (unused)
e100 60644 1
ext3 70784 2
jbd 51892 2 [ext3]
aic7xxx 141236 0
megaraid 30820 4
sd_mod 13452 8
scsi_mod 107128 3 [aic7xxx megaraid sd_mod]
Die Google Groups und Web Suche hat mir leider nicht mehr weitergeholfen. Evtl gibt es auch eine Möglichkeit ISDN ganz LOW LEVEL zu testen? Wie kann man die ISDN Karte auf defekt testen?
Gruß,
Schnitz
Ich habe eine Red Hat 9 Büchse mit einer Fritz Card und will yaps über /dev/ttyI0 einrichten. Das ganze _hat_ auch schon funktioniert. Jetzt hängt der ISDN Anschluss allerdings nicht mehr an einer TK Anlage sondern direkt an einem echten S0 Bus.
Wenn Ich versuche mich mit yaps einzuwählen passiert folgendes:
[root@nagios root]# yaps 0175XXXX test
Found service D1 for 0175XXXX
Sending following message:
0175XXXX (D1, 0175XXXX): test powered by XXX
Trying to open /dev/ttyI0 for modem standard
[Hangup]
[Send] <cr>
[Cmd Mdzz 200]
[Send] ATZ<cr>
[Expect] <cr>ATZ<cr><cr><lf>OK got OK
[Send] AT&E0<cr>
[Expect] <cr><lf>AT&E0<cr><cr><lf>OK got OK
Using modem standard at 38400 bps, 8n1 over /dev/ttyI0
Trying do dial 01712521001
[Send] ATD01712521001<cr>
[Expect] <cr><lf>ATD01712521001<cr><cr><lf>NO DIALTONE got NO DIALTONE
Unable to dial D1
In /etc/yaps.rc ist folgendes eingestellt (Auszüge):
device /dev/ttyI0
# habe ich auch schon mit der rufnummer ohne vorwahl anstatt der 0 probiert
init \\r !200D ATZ\r <OK AT&E0\r <OK
dial ATD%L\r <60CONNECT|OK|BUSY|NO\sDIALTONE|NO\sCARRIER
reset ATZ\r <OK
timeout 10
modems standard
speed 38400
bits-per-byte 8
parity none
stopbits 1
cv-default {
Ä [
Ö \
Ü ]
ä {
ö |
ü }
ß ~
}
cv-extend {
\l \s
\n \s
\r \s
\f \s
\t \s
}
lsmod erzeugt folgendes:
Module Size Used by Not tainted
hisax 549348 0 (unused)
isdn 137984 0 [hisax]
slhc 6740 0 [isdn]
kernelcapi 33792 0
capiutil 24864 0 [kernelcapi]
capifs 5420 0
nfs 81336 2 (autoclean)
lockd 58704 1 (autoclean) [nfs]
sunrpc 81564 1 (autoclean) [nfs lockd]
iptable_filter 2412 0 (autoclean) (unused)
ip_tables 15096 1 [iptable_filter]
autofs 13268 0 (autoclean) (unused)
e100 60644 1
ext3 70784 2
jbd 51892 2 [ext3]
aic7xxx 141236 0
megaraid 30820 4
sd_mod 13452 8
scsi_mod 107128 3 [aic7xxx megaraid sd_mod]
Die Google Groups und Web Suche hat mir leider nicht mehr weitergeholfen. Evtl gibt es auch eine Möglichkeit ISDN ganz LOW LEVEL zu testen? Wie kann man die ISDN Karte auf defekt testen?
Gruß,
Schnitz