meinereinerseiner
13.02.04, 21:08
hi,
hab heute versucht meine pcmcia wlan karte (smc2835w) unter gentoo
zum laufen zu bringen. (2.6.1-gentoo-r1)
alles nach der anleitung von hier (http://prism54.org/forums/viewtopic.php?t=253) gemacht und karte rein, einzige meldung in messages:
PCMCIA: socket cedba044: unable to apply power.
gut, karte drinn gelassen und mal gebootet und dann kam folgendes:
Feb 13 21:17:07 jvc-tux Linux Kernel Card Services
Feb 13 21:17:07 jvc-tux options: [pci] [cardbus] [pm]
Feb 13 21:17:07 jvc-tux Yenta: CardBus bridge found at 0000:00:09.0 [1043:1674]
Feb 13 21:17:07 jvc-tux Yenta: ISA IRQ mask 0x0408, PCI irq 11
Feb 13 21:17:07 jvc-tux Socket status: 30000820
Feb 13 21:17:07 jvc-tux Yenta: CardBus bridge found at 0000:00:09.1 [1043:1674]
Feb 13 21:17:07 jvc-tux Yenta: ISA IRQ mask 0x0408, PCI irq 11
Feb 13 21:17:07 jvc-tux Socket status: 30000006
Feb 13 21:17:07 jvc-tux Loaded prism54 driver, version 1.0.2.2
Feb 13 21:17:07 jvc-tux PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Feb 13 21:17:07 jvc-tux eth1: islpci_open()
Feb 13 21:17:07 jvc-tux eth1: resetting device...
Feb 13 21:17:07 jvc-tux eth1: uploading firmware...
Feb 13 21:17:07 jvc-tux eth1: firmware uploaded done, now triggering reset...
Feb 13 21:17:07 jvc-tux eth1: prism54_mib_init()
Feb 13 21:17:07 jvc-tux eth1: done with prism54_mib_init()! -- Client Managed mode
Feb 13 21:17:07 jvc-tux Real Time Clock Driver v1.12
Feb 13 21:17:07 jvc-tux TRAP: oid 0x18000001, device 3, flags 0x0 length 12
Feb 13 21:17:07 jvc-tux TRAP: oid 0x18000003, device 3, flags 0x0 length 12
Feb 13 21:17:07 jvc-tux TRAP: oid 0x1, device 3, flags 0x0 length 4
Feb 13 21:17:08 jvc-tux cardmgr[3331]: watching 2 sockets
Feb 13 21:17:08 jvc-tux cs: IO port probe 0x0c00-0x0cff: clean.
Feb 13 21:17:08 jvc-tux cs: IO port probe 0x0800-0x08ff: clean.
Feb 13 21:17:08 jvc-tux cs: IO port probe 0x0100-0x04ff: excluding 0x3c0-0x3df 0x480-0x48f 0x4d0-0x4d7
Feb 13 21:17:08 jvc-tux cs: IO port probe 0x0a00-0x0aff: clean.
das sieht ja so schlecht nicht aus, bekomme zwar keine verbindung, aber naja.
was mich verwirrt ist die meldung:
Feb 13 21:17:08 jvc-tux cardmgr[3331]: watching 2 sockets
weil, ich hab nur 1 steckplatz.
googeln brachte mich auf 2 seiten die erste (http://rnbhq.org/pipermail/r31/2003-October/000297.html) und dann diese hier (http://lkml.org/slashdot.php?mid=446620) .
bei der ersten sollte der fehlende ISA support die ursache sein, hab ich aber aktiviert
und bei der zweiten gehts um CIS, das sagt mir aber garnix.
NACHTRAG:
hab noch etwas rausgefunden, wenn ich die smc karte rausziehe und mal eine
orinoco einsetze und dannach wieder die smc, fängt er an die treiber zu laden:
Feb 13 22:20:55 jvc-tux PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Feb 13 22:20:56 jvc-tux eth1: islpci_open()
Feb 13 22:20:56 jvc-tux eth1: resetting device...
Feb 13 22:20:56 jvc-tux eth1: uploading firmware...
Feb 13 22:20:56 jvc-tux eth1: firmware uploaded done, now triggering reset...
Feb 13 22:20:56 jvc-tux Unable to handle kernel NULL pointer dereference at virtual address 00000020
Feb 13 22:20:56 jvc-tux printing eip:
Feb 13 22:20:56 jvc-tux c019838d
Feb 13 22:20:56 jvc-tux *pde = 00000000
Feb 13 22:20:56 jvc-tux Oops: 0000 [#1]
Feb 13 22:20:56 jvc-tux CPU: 0
Feb 13 22:20:56 jvc-tux EIP: 0060:[<c019838d>] Not tainted
Feb 13 22:20:56 jvc-tux EFLAGS: 00010282
Feb 13 22:20:56 jvc-tux EIP is at dnotify_flush+0x1d/0x90
Feb 13 22:20:56 jvc-tux eax: cc910d80 ebx: cc752380 ecx: 40156b20 edx: 00000000
Feb 13 22:20:56 jvc-tux esi: cc773300 edi: cc752380 ebp: cc678000 esp: cc679f68
Feb 13 22:20:56 jvc-tux ds: 007b es: 007b ss: 0068
Feb 13 22:20:56 jvc-tux Process default.hotplug (pid: 4904, threadinfo=cc678000 task=ccb750c0)
Feb 13 22:20:56 jvc-tux Stack: cc679fbc 00000082 cc752380 00000000 cc773300 c01710f6 cc752380 cc773300
Feb 13 22:20:56 jvc-tux cc773300 00000001 cc752380 c017122f cc752380 cc773300 e4280a96 00000056
Feb 13 22:20:56 jvc-tux ccb750c0 ccb752b4 00000001 00000001 00000000 00000001 c010a04f 00000001
Feb 13 22:20:56 jvc-tux Call Trace:
Feb 13 22:20:56 jvc-tux [<c01710f6>] filp_close+0x46/0x90
Feb 13 22:20:56 jvc-tux [<c017122f>] sys_close+0xef/0x200
Feb 13 22:20:56 jvc-tux [<c010a04f>] syscall_call+0x7/0xb
Feb 13 22:20:56 jvc-tux
Feb 13 22:20:56 jvc-tux Code: 0f b7 42 20 25 00 f0 00 00 3d 00 40 00 00 74 13 8b 5c 24 08
Feb 13 22:20:56 jvc-tux dhcpcd[4902]: dhcpStart: retrying MAC address request (returned 00:00:00:00:00:00)
Feb 13 22:20:56 jvc-tux dhcpcd[4902]: dhcpStart: retrying MAC address request (returned 00:00:00:00:00:00)
Feb 13 22:20:56 jvc-tux rc-scripts: WARNING: "net.eth1" has already been started.
Feb 13 22:20:56 jvc-tux <7>eth1: prism54_mib_init()
Feb 13 22:20:56 jvc-tux eth1: done with prism54_mib_init()! -- Client Managed mode
Feb 13 22:20:57 jvc-tux TRAP: oid 0x18000001, device 6, flags 0x0 length 12
Feb 13 22:20:57 jvc-tux TRAP: oid 0x18000003, device 6, flags 0x0 length 12
Feb 13 22:20:57 jvc-tux TRAP: oid 0x1, device 6, flags 0x0 length 4
Feb 13 22:20:59 jvc-tux eth1: prism54_mib_init()
Feb 13 22:20:59 jvc-tux eth1: done with prism54_mib_init()! -- Client Managed mode
Feb 13 22:20:59 jvc-tux modprobe: FATAL: Module snd_trident already in kernel.
Feb 13 22:21:00 jvc-tux TRAP: oid 0x18000001, device 6, flags 0x0 length 12
Feb 13 22:21:00 jvc-tux TRAP: oid 0x18000003, device 6, flags 0x0 length 12
Feb 13 22:21:00 jvc-tux TRAP: oid 0x1, device 6, flags 0x0 length 4
Feb 13 22:21:56 jvc-tux dhcpcd[4902]: timed out waiting for a valid DHCP server response
Feb 13 22:21:56 jvc-tux eth1: islpci_close ()
Feb 13 22:21:56 jvc-tux rc-scripts: Failed to bring eth1 up
interesant is dabei vielleicht:
Feb 13 22:20:56 jvc-tux Unable to handle kernel NULL pointer dereference at virtual address 00000020
Feb 13 22:20:56 jvc-tux printing eip:
Feb 13 22:20:56 jvc-tux c019838d
Feb 13 22:20:56 jvc-tux *pde = 00000000
Feb 13 22:20:56 jvc-tux Oops: 0000 [#1]
ich weis nun garnicht mehr weiter...... :(
hat jemand vielleicht einen tipp für mich?
vielen dank
der tom:rolleyes: :rolleyes:
hab heute versucht meine pcmcia wlan karte (smc2835w) unter gentoo
zum laufen zu bringen. (2.6.1-gentoo-r1)
alles nach der anleitung von hier (http://prism54.org/forums/viewtopic.php?t=253) gemacht und karte rein, einzige meldung in messages:
PCMCIA: socket cedba044: unable to apply power.
gut, karte drinn gelassen und mal gebootet und dann kam folgendes:
Feb 13 21:17:07 jvc-tux Linux Kernel Card Services
Feb 13 21:17:07 jvc-tux options: [pci] [cardbus] [pm]
Feb 13 21:17:07 jvc-tux Yenta: CardBus bridge found at 0000:00:09.0 [1043:1674]
Feb 13 21:17:07 jvc-tux Yenta: ISA IRQ mask 0x0408, PCI irq 11
Feb 13 21:17:07 jvc-tux Socket status: 30000820
Feb 13 21:17:07 jvc-tux Yenta: CardBus bridge found at 0000:00:09.1 [1043:1674]
Feb 13 21:17:07 jvc-tux Yenta: ISA IRQ mask 0x0408, PCI irq 11
Feb 13 21:17:07 jvc-tux Socket status: 30000006
Feb 13 21:17:07 jvc-tux Loaded prism54 driver, version 1.0.2.2
Feb 13 21:17:07 jvc-tux PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Feb 13 21:17:07 jvc-tux eth1: islpci_open()
Feb 13 21:17:07 jvc-tux eth1: resetting device...
Feb 13 21:17:07 jvc-tux eth1: uploading firmware...
Feb 13 21:17:07 jvc-tux eth1: firmware uploaded done, now triggering reset...
Feb 13 21:17:07 jvc-tux eth1: prism54_mib_init()
Feb 13 21:17:07 jvc-tux eth1: done with prism54_mib_init()! -- Client Managed mode
Feb 13 21:17:07 jvc-tux Real Time Clock Driver v1.12
Feb 13 21:17:07 jvc-tux TRAP: oid 0x18000001, device 3, flags 0x0 length 12
Feb 13 21:17:07 jvc-tux TRAP: oid 0x18000003, device 3, flags 0x0 length 12
Feb 13 21:17:07 jvc-tux TRAP: oid 0x1, device 3, flags 0x0 length 4
Feb 13 21:17:08 jvc-tux cardmgr[3331]: watching 2 sockets
Feb 13 21:17:08 jvc-tux cs: IO port probe 0x0c00-0x0cff: clean.
Feb 13 21:17:08 jvc-tux cs: IO port probe 0x0800-0x08ff: clean.
Feb 13 21:17:08 jvc-tux cs: IO port probe 0x0100-0x04ff: excluding 0x3c0-0x3df 0x480-0x48f 0x4d0-0x4d7
Feb 13 21:17:08 jvc-tux cs: IO port probe 0x0a00-0x0aff: clean.
das sieht ja so schlecht nicht aus, bekomme zwar keine verbindung, aber naja.
was mich verwirrt ist die meldung:
Feb 13 21:17:08 jvc-tux cardmgr[3331]: watching 2 sockets
weil, ich hab nur 1 steckplatz.
googeln brachte mich auf 2 seiten die erste (http://rnbhq.org/pipermail/r31/2003-October/000297.html) und dann diese hier (http://lkml.org/slashdot.php?mid=446620) .
bei der ersten sollte der fehlende ISA support die ursache sein, hab ich aber aktiviert
und bei der zweiten gehts um CIS, das sagt mir aber garnix.
NACHTRAG:
hab noch etwas rausgefunden, wenn ich die smc karte rausziehe und mal eine
orinoco einsetze und dannach wieder die smc, fängt er an die treiber zu laden:
Feb 13 22:20:55 jvc-tux PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Feb 13 22:20:56 jvc-tux eth1: islpci_open()
Feb 13 22:20:56 jvc-tux eth1: resetting device...
Feb 13 22:20:56 jvc-tux eth1: uploading firmware...
Feb 13 22:20:56 jvc-tux eth1: firmware uploaded done, now triggering reset...
Feb 13 22:20:56 jvc-tux Unable to handle kernel NULL pointer dereference at virtual address 00000020
Feb 13 22:20:56 jvc-tux printing eip:
Feb 13 22:20:56 jvc-tux c019838d
Feb 13 22:20:56 jvc-tux *pde = 00000000
Feb 13 22:20:56 jvc-tux Oops: 0000 [#1]
Feb 13 22:20:56 jvc-tux CPU: 0
Feb 13 22:20:56 jvc-tux EIP: 0060:[<c019838d>] Not tainted
Feb 13 22:20:56 jvc-tux EFLAGS: 00010282
Feb 13 22:20:56 jvc-tux EIP is at dnotify_flush+0x1d/0x90
Feb 13 22:20:56 jvc-tux eax: cc910d80 ebx: cc752380 ecx: 40156b20 edx: 00000000
Feb 13 22:20:56 jvc-tux esi: cc773300 edi: cc752380 ebp: cc678000 esp: cc679f68
Feb 13 22:20:56 jvc-tux ds: 007b es: 007b ss: 0068
Feb 13 22:20:56 jvc-tux Process default.hotplug (pid: 4904, threadinfo=cc678000 task=ccb750c0)
Feb 13 22:20:56 jvc-tux Stack: cc679fbc 00000082 cc752380 00000000 cc773300 c01710f6 cc752380 cc773300
Feb 13 22:20:56 jvc-tux cc773300 00000001 cc752380 c017122f cc752380 cc773300 e4280a96 00000056
Feb 13 22:20:56 jvc-tux ccb750c0 ccb752b4 00000001 00000001 00000000 00000001 c010a04f 00000001
Feb 13 22:20:56 jvc-tux Call Trace:
Feb 13 22:20:56 jvc-tux [<c01710f6>] filp_close+0x46/0x90
Feb 13 22:20:56 jvc-tux [<c017122f>] sys_close+0xef/0x200
Feb 13 22:20:56 jvc-tux [<c010a04f>] syscall_call+0x7/0xb
Feb 13 22:20:56 jvc-tux
Feb 13 22:20:56 jvc-tux Code: 0f b7 42 20 25 00 f0 00 00 3d 00 40 00 00 74 13 8b 5c 24 08
Feb 13 22:20:56 jvc-tux dhcpcd[4902]: dhcpStart: retrying MAC address request (returned 00:00:00:00:00:00)
Feb 13 22:20:56 jvc-tux dhcpcd[4902]: dhcpStart: retrying MAC address request (returned 00:00:00:00:00:00)
Feb 13 22:20:56 jvc-tux rc-scripts: WARNING: "net.eth1" has already been started.
Feb 13 22:20:56 jvc-tux <7>eth1: prism54_mib_init()
Feb 13 22:20:56 jvc-tux eth1: done with prism54_mib_init()! -- Client Managed mode
Feb 13 22:20:57 jvc-tux TRAP: oid 0x18000001, device 6, flags 0x0 length 12
Feb 13 22:20:57 jvc-tux TRAP: oid 0x18000003, device 6, flags 0x0 length 12
Feb 13 22:20:57 jvc-tux TRAP: oid 0x1, device 6, flags 0x0 length 4
Feb 13 22:20:59 jvc-tux eth1: prism54_mib_init()
Feb 13 22:20:59 jvc-tux eth1: done with prism54_mib_init()! -- Client Managed mode
Feb 13 22:20:59 jvc-tux modprobe: FATAL: Module snd_trident already in kernel.
Feb 13 22:21:00 jvc-tux TRAP: oid 0x18000001, device 6, flags 0x0 length 12
Feb 13 22:21:00 jvc-tux TRAP: oid 0x18000003, device 6, flags 0x0 length 12
Feb 13 22:21:00 jvc-tux TRAP: oid 0x1, device 6, flags 0x0 length 4
Feb 13 22:21:56 jvc-tux dhcpcd[4902]: timed out waiting for a valid DHCP server response
Feb 13 22:21:56 jvc-tux eth1: islpci_close ()
Feb 13 22:21:56 jvc-tux rc-scripts: Failed to bring eth1 up
interesant is dabei vielleicht:
Feb 13 22:20:56 jvc-tux Unable to handle kernel NULL pointer dereference at virtual address 00000020
Feb 13 22:20:56 jvc-tux printing eip:
Feb 13 22:20:56 jvc-tux c019838d
Feb 13 22:20:56 jvc-tux *pde = 00000000
Feb 13 22:20:56 jvc-tux Oops: 0000 [#1]
ich weis nun garnicht mehr weiter...... :(
hat jemand vielleicht einen tipp für mich?
vielen dank
der tom:rolleyes: :rolleyes: