Anzeige:
Ergebnis 1 bis 15 von 15

Thema: DVB-S mit kaffeine ruckelt

  1. #1
    Registrierter Benutzer Avatar von michel_vaclav
    Registriert seit
    Jan 2003
    Ort
    daheim
    Beiträge
    1.052

    DVB-S mit kaffeine ruckelt

    Hallo,

    nachdem mein alter Rechner den Geist aufgegeben hat, habe ich mir einen neuen geleistet und meine alte Skystar2-DVB-S-Karte wieder eingebaut. Hat auch bei den ersten beiden Installationen problemlos funktioniert. Allerdings bei der dritten Installation leider nicht mehr.

    Fehlerbild: Auf manchen Sendern (nicht alle!) stottert der Ton gleich von Beginn an, nach einigen Sekunden bilden sich Klötzchen, bis das Bild zeitweise komplett einfriert.

    Woran kann das liegen?

    Details:
    • openSUSE 10.2 64bit
    • kaffeine 0.8.6 von Packman
    • w32-codecs von Packman
    • libxine von Packman
    • libxine-dvb von Packman

    Was ich sonst noch probiert habe:
    • mit xine-ui und dem direkten Abspielen klappt es
    • mit mplayer klappt es
    • DVDs gehen ohne Probleme mit kaffeine
    • Karte auf anderen Steckplatz gesteckt
    • edit1: Sowohl kaffeine alsauch die w32-codecs aus den Quellen kompiliert


    Was könnte ich noch probieren?

    dmesg:
    Code:
    Linux version 2.6.22.18-0.2-default (geeko@buildhost) (gcc version 4.2.1 (SUSE Linux)) #1 SMP 2008-06-09 13:53:20 +0200
    Command line: root=/dev/disk/by-id/scsi-SATA_SAMSUNG_HD502IJS13TJDWQ346740-part6 vga=0x31a resume=/dev/sda5 splash=silent
    BIOS-provided physical RAM map:
     BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
     BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
     BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
     BIOS-e820: 0000000000100000 - 000000007ff80000 (usable)
     BIOS-e820: 000000007ff80000 - 000000007ff8e000 (ACPI data)
     BIOS-e820: 000000007ff8e000 - 000000007ffe0000 (ACPI NVS)
     BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
     BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
     BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
    Entering add_active_range(0, 0, 159) 0 entries of 3200 used
    Entering add_active_range(0, 256, 524160) 1 entries of 3200 used
    end_pfn_map = 1048576
    DMI 2.4 present.
    ACPI: RSDP 000FBCD0, 0014 (r0 ACPIAM)
    ACPI: RSDT 7FF80000, 003C (r1 A_M_I_ OEMRSDT  12000724 MSFT       97)
    ACPI: FACP 7FF80200, 0084 (r2 A_M_I_ OEMFACP  12000724 MSFT       97)
    ACPI: DSDT 7FF805C0, 90A1 (r1  A0751 A0751067       67 INTL 20060113)
    ACPI: FACS 7FF8E000, 0040
    ACPI: APIC 7FF80390, 006C (r1 A_M_I_ OEMAPIC  12000724 MSFT       97)
    ACPI: MCFG 7FF80400, 003C (r1 A_M_I_ OEMMCFG  12000724 MSFT       97)
    ACPI: OEMB 7FF8E040, 0081 (r1 A_M_I_ AMI_OEM  12000724 MSFT       97)
    ACPI: HPET 7FF89670, 0038 (r1 A_M_I_ OEMHPET  12000724 MSFT       97)
    ACPI: OSFR 7FF896B0, 00B0 (r1 A_M_I_ OEMOSFR  12000724 MSFT       97)
    No NUMA configuration found
    Faking a node at 0000000000000000-000000007ff80000
    Entering add_active_range(0, 0, 159) 0 entries of 3200 used
    Entering add_active_range(0, 256, 524160) 1 entries of 3200 used
    Bootmem setup node 0 0000000000000000-000000007ff80000
    Zone PFN ranges:
      DMA             0 ->     4096
      DMA32        4096 ->  1048576
      Normal    1048576 ->  1048576
    early_node_map[2] active PFN ranges
        0:        0 ->      159
        0:      256 ->   524160
    On node 0 totalpages: 524063
      DMA zone: 56 pages used for memmap
      DMA zone: 1271 pages reserved
      DMA zone: 2672 pages, LIFO batch:0
      DMA32 zone: 7110 pages used for memmap
      DMA32 zone: 512954 pages, LIFO batch:31
      Normal zone: 0 pages used for memmap
    ACPI: PM-Timer IO Port: 0x808
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    Processor #0 (Bootup-CPU)
    ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    Processor #1
    ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
    Processor #2
    ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
    Processor #3
    ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 4, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Setting APIC routing to flat
    ACPI: HPET id: 0xffffffff base: 0xfed00000
    Using ACPI (MADT) for SMP configuration information
    swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
    swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e4000
    swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000
    Allocating PCI resources starting at 88000000 (gap: 80000000:7ee00000)
    SMP: Allowing 4 CPUs, 0 hotplug CPUs
    PERCPU: Allocating 50296 bytes of per cpu data
    Built 1 zonelists.  Total pages: 515626
    Kernel command line: root=/dev/disk/by-id/scsi-SATA_SAMSUNG_HD502IJS13TJDWQ346740-part6 vga=0x31a resume=/dev/sda5 splash=silent
    bootsplash: silent mode.
    Initializing CPU#0
    PID hash table entries: 4096 (order: 12, 32768 bytes)
    time.c: Detected 2400.084 MHz processor.
    Console: colour dummy device 80x25
    Checking aperture...
    Calgary: detecting Calgary via BIOS EBDA area
    Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    Memory: 2059460k/2096640k available (2054k kernel code, 36792k reserved, 1017k data, 316k init)
    Calibrating delay using timer specific routine.. 4803.42 BogoMIPS (lpj=9606843)
    Security Framework v1.0.0 initialized
    Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
    Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
    Mount-cache hash table entries: 256
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 4096K
    CPU 0/0 -> Node 0
    using mwait in idle threads.
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 0
    CPU0: Thermal monitoring enabled (TM2)
    SMP alternatives: switching to UP code
    Unpacking initramfs... done
    Freeing initrd memory: 2705k freed
    ACPI: Core revision 20070126
    Parsing all Control Methods:
    Table [DSDT](id 0001) - 993 Objects with 75 Devices 278 Methods 35 Regions
     tbxface-0587 [00] tb_load_namespace     : ACPI Tables successfully acquired
    evxfevnt-0091 [00] enable                : Transition to ACPI mode successful
    Using local APIC timer interrupts.
    result 16667236
    Detected 16.667 MHz APIC timer.
    SMP alternatives: switching to SMP code
    Booting processor 1/4 APIC 0x1
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 4800.22 BogoMIPS (lpj=9600448)
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 4096K
    CPU 1/1 -> Node 0
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    CPU1: Thermal monitoring enabled (TM2)
    Intel(R) Core(TM)2 Quad CPU    Q6600  @ 2.40GHz stepping 0b
    checking TSC synchronization [CPU#0 -> CPU#1]: passed.
    SMP alternatives: switching to SMP code
    Booting processor 2/4 APIC 0x2
    Initializing CPU#2
    Calibrating delay using timer specific routine.. 4800.24 BogoMIPS (lpj=9600491)
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 4096K
    CPU 2/2 -> Node 0
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 2
    CPU2: Thermal monitoring enabled (TM2)
    Intel(R) Core(TM)2 Quad CPU    Q6600  @ 2.40GHz stepping 0b
    checking TSC synchronization [CPU#0 -> CPU#2]: passed.
    SMP alternatives: switching to SMP code
    Booting processor 3/4 APIC 0x3
    Initializing CPU#3
    Calibrating delay using timer specific routine.. 4800.24 BogoMIPS (lpj=9600483)
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 4096K
    CPU 3/3 -> Node 0
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 3
    CPU3: Thermal monitoring enabled (TM2)
    Intel(R) Core(TM)2 Quad CPU    Q6600  @ 2.40GHz stepping 0b
    checking TSC synchronization [CPU#0 -> CPU#3]: passed.
    Brought up 4 CPUs
    migration_cost=14,4017
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
    PCI: Not using MMCONFIG.
    PCI: Using configuration type 1
    evgpeblk-0956 [00] ev_create_gpe_block   : GPE 00 to 3F [_GPE] 8 regs on int 0x9
    evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 11 Wake, Enabled 2 Runtime GPEs in this block
    ACPI: EC: Look up EC in DSDT
    Completing Region/Field/Buffer/Package initialization:......................................................................................................................................................................................................................
    Initialized 29/35 Regions 44/44 Fields 48/48 Buffers 93/95 Packages (1002 nodes)
    Initializing Device/Processor/Thermal objects by executing _INI methods:.
    Executed 1 _INI methods requiring 1 _STA executions (examined 81 objects)
    ACPI: Interpreter enabled
    ACPI: (supports S0 S1 S3 S4 S5)
    ACPI: Using IOAPIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Probing PCI hardware (bus 00)
    PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
    PCI quirk: region 0480-04bf claimed by ICH6 GPIO
    PCI: Transparent bridge - 0000:00:1e.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 *14 15)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 *15)
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp: PnP ACPI: found 14 devices
    ACPI: ACPI bus type pnp unregistered
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
    PCI-GART: No AMD northbridge found.
    hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
    hpet0: 4 64-bit timers, 14318180 Hz
    ACPI: RTC can wake from S4
    pnp: 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
    pnp: 00:06: ioport range 0x290-0x297 has been reserved
    pnp: 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved
    pnp: 00:07: iomem range 0xfed20000-0xfed3ffff has been reserved
    pnp: 00:07: iomem range 0xfed50000-0xfed8ffff has been reserved
    pnp: 00:07: iomem range 0xffa00000-0xffafffff has been reserved
    pnp: 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
    pnp: 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
    pnp: 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
    pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved
    pnp: 00:0d: iomem range 0xc0000-0xcffff has been reserved
    pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved
    pnp: 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
    PCI: Bridge: 0000:00:01.0
      IO window: c000-cfff
      MEM window: fa000000-fe8fffff
      PREFETCH window: d0000000-dfffffff
    PCI: Bridge: 0000:00:1c.0
      IO window: disabled.
      MEM window: disabled.
      PREFETCH window: f8f00000-f8ffffff
    PCI: Bridge: 0000:00:1c.4
      IO window: d000-dfff
      MEM window: fea00000-feafffff
      PREFETCH window: 88000000-880fffff
    PCI: Bridge: 0000:00:1c.5
      IO window: disabled.
      MEM window: fe900000-fe9fffff
      PREFETCH window: disabled.
    PCI: Bridge: 0000:00:1e.0
      IO window: e000-efff
      MEM window: feb00000-febfffff
      PREFETCH window: disabled.
    ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1c.4 to 64
    ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1c.5 to 64
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    NET: Registered protocol family 2
    Time: tsc clocksource has been installed.
    IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
    TCP established hash table entries: 262144 (order: 10, 6291456 bytes)
    TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    TCP: Hash tables configured (established 262144 bind 65536)
    TCP reno registered
    audit: initializing netlink socket (disabled)
    audit(1213900565.288:1): initialized
    Total HugeTLB memory allocated, 0
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    Boot video device is 0000:01:00.0
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:01.0:pcie00]
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:1c.0:pcie00]
    Allocate Port Service[0000:00:1c.0:pcie02]
    PCI: Setting latency timer of device 0000:00:1c.4 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:1c.4:pcie00]
    Allocate Port Service[0000:00:1c.4:pcie02]
    PCI: Setting latency timer of device 0000:00:1c.5 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:1c.5:pcie00]
    Allocate Port Service[0000:00:1c.5:pcie02]
    vesafb: framebuffer at 0xfb000000, mapped to 0xffffc20000b00000, using 10240k, total 14336k
    vesafb: mode is 1280x1024x16, linelength=2560, pages=1
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    bootsplash 3.1.6-2004/03/31: looking for picture...
    bootsplash: silentjpeg size 98233 bytes
    bootsplash: ...found (1280x1024, 35219 bytes, v3).
    Console: switching to colour frame buffer device 156x60
    fb0: VESA VGA frame buffer device
    Real Time Clock Driver v1.12ac
    hpet_resources: 0xfed00000 is busy
    Non-volatile memory driver v1.2
    Linux agpgart interface v0.102 (c) Dave Jones
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
    PNP: PS/2 controller doesn't have AUX irq; using default 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    input: AT Translated Set 2 keyboard as /class/input/input0
    input: PC Speaker as /class/input/input1
    NET: Registered protocol family 1
    Freeing unused kernel memory: 316k freed
    ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] -  B1, should be B0 [20070126]
    ACPI: SSDT 7FF8E0D0, 01D2 (r1    AMI   CPU1PM        1 INTL 20060113)
    Parsing all Control Methods:
    Table [SSDT](id 00A9) - 9 Objects with 0 Devices 3 Methods 0 Regions
    ACPI: SSDT 7FF8E2B0, 0143 (r1    AMI   CPU2PM        1 INTL 20060113)
    Parsing all Control Methods:
    Table [SSDT](id 00AC) - 7 Objects with 0 Devices 4 Methods 0 Regions
    ACPI: SSDT 7FF8E400, 0143 (r1    AMI   CPU3PM        1 INTL 20060113)
    Parsing all Control Methods:
    Table [SSDT](id 00AF) - 7 Objects with 0 Devices 4 Methods 0 Regions
    ACPI: SSDT 7FF8E550, 0143 (r1    AMI   CPU4PM        1 INTL 20060113)
    Parsing all Control Methods:
    Table [SSDT](id 00B2) - 7 Objects with 0 Devices 4 Methods 0 Regions
    SCSI subsystem initialized
    libata version 3.00 loaded.
    ahci 0000:03:00.0: version 3.0
    ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
    ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
    ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part
    PCI: Setting latency timer of device 0000:03:00.0 to 64
    scsi0 : ahci
    scsi1 : ahci
    ata1: SATA max UDMA/133 cmd 0xffffc20000ac4100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16
    ata2: SATA max UDMA/133 cmd 0xffffc20000ac4180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16
    ata1: SATA link down (SStatus 0 SControl 300)
    ata2: SATA link down (SStatus 0 SControl 300)
    ata_piix 0000:00:1f.2: version 2.11
    ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 22 (level, low) -> IRQ 22
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    scsi2 : ata_piix
    scsi3 : ata_piix
    ata3: SATA max UDMA/133 cmd 0x000000000001a000 ctl 0x0000000000019c02 bmdma 0x0000000000019480 irq 22
    ata4: SATA max UDMA/133 cmd 0x0000000000019880 ctl 0x0000000000019802 bmdma 0x0000000000019488 irq 22
    ata3.00: ATA-7: SAMSUNG HD502IJ, 1AA01109, max UDMA7
    ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
    ata3.00: configured for UDMA/133
    ata4.00: ATAPI: HL-DT-ST DVDRAM GH20NS10, EL00, max UDMA/100
    ata4.00: configured for UDMA/100
    ata4: EH pending after completion, repeating EH (cnt=4)
    scsi 2:0:0:0: Direct-Access     ATA      SAMSUNG HD502IJ  1AA0 PQ: 0 ANSI: 5
    scsi 3:0:0:0: CD-ROM            HL-DT-ST DVDRAM GH20NS10  EL00 PQ: 0 ANSI: 5
    ata_piix 0000:00:1f.5: MAP [ P0 P2 P1 P3 ]
    ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 22 (level, low) -> IRQ 22
    PCI: Setting latency timer of device 0000:00:1f.5 to 64
    scsi4 : ata_piix
    scsi5 : ata_piix
    ata5: SATA max UDMA/133 cmd 0x000000000001b000 ctl 0x000000000001ac02 bmdma 0x000000000001a480 irq 22
    ata6: SATA max UDMA/133 cmd 0x000000000001a880 ctl 0x000000000001a802 bmdma 0x000000000001a488 irq 22
    PCI: Enabling device 0000:03:00.1 (0000 -> 0001)
    ACPI: PCI Interrupt 0000:03:00.1[B] -> GSI 17 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:03:00.1 to 64
    scsi6 : pata_jmicron
    scsi7 : pata_jmicron
    ata7: PATA max UDMA/100 cmd 0x000000000001dc00 ctl 0x000000000001d882 bmdma 0x000000000001d400 irq 17
    ata8: PATA max UDMA/100 cmd 0x000000000001d800 ctl 0x000000000001d482 bmdma 0x000000000001d408 irq 17
    ata7.00: HPA unlocked: 66055248 -> 488397168, native 488397168
    ata7.00: ATA-7: SAMSUNG SP2514N, VF100-50, max UDMA/100
    ata7.00: 488397168 sectors, multi 0: LBA48
    ata7.00: configured for UDMA/100
    scsi 6:0:0:0: Direct-Access     ATA      SAMSUNG SP2514N  VF10 PQ: 0 ANSI: 5
    DC390: clustering now enabled by default. If you get problems load
            with "disable_clustering=1" and report to maintainers
    BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    USB Universal Host Controller Interface driver v3.0
    ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1a.0 to 64
    uhci_hcd 0000:00:1a.0: UHCI Host Controller
    uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
    sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
     sda: sda1 sda2 < sda5 sda6<6>uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000b800
     sda7 >
    usb usb1: new device found, idVendor=0000, idProduct=0000
    sd 2:0:0:0: [sda] Attached SCSI disk
    sd 6:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
    sd 6:0:0:0: [sdb] Write Protect is off
    sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sd 6:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
    sd 6:0:0:0: [sdb] Write Protect is off
    sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
     sdb:
    usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
    sd 6:0:0:0: [sdb] Attached SCSI disk
    usb usb1: Product: UHCI Host Controller
    usb usb1: Manufacturer: Linux 2.6.22.18-0.2-default uhci_hcd
    usb usb1: SerialNumber: 0000:00:1a.0
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
    PCI: Setting latency timer of device 0000:00:1a.1 to 64
    uhci_hcd 0000:00:1a.1: UHCI Host Controller
    uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000b880
    usb usb2: new device found, idVendor=0000, idProduct=0000
    usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb2: Product: UHCI Host Controller
    usb usb2: Manufacturer: Linux 2.6.22.18-0.2-default uhci_hcd
    usb usb2: SerialNumber: 0000:00:1a.1
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1a.2 to 64
    uhci_hcd 0000:00:1a.2: UHCI Host Controller
    uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000bc00
    usb usb3: new device found, idVendor=0000, idProduct=0000
    usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb3: Product: UHCI Host Controller
    usb usb3: Manufacturer: Linux 2.6.22.18-0.2-default uhci_hcd
    usb usb3: SerialNumber: 0000:00:1a.2
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    usb 1-2: new low speed USB device using uhci_hcd and address 2
    hub 3-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000b080
    usb usb4: new device found, idVendor=0000, idProduct=0000
    usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb4: Product: UHCI Host Controller
    usb usb4: Manufacturer: Linux 2.6.22.18-0.2-default uhci_hcd
    usb usb4: SerialNumber: 0000:00:1d.0
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    usb 1-2: new device found, idVendor=046d, idProduct=c045
    usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
    usb 1-2: Product: USB-PS/2 Optical Mouse
    usb 1-2: Manufacturer: Logitech
    usb 1-2: configuration #1 chosen from 1 choice
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
    uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b400
    usb usb5: new device found, idVendor=0000, idProduct=0000
    usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb5: Product: UHCI Host Controller
    usb usb5: Manufacturer: Linux 2.6.22.18-0.2-default uhci_hcd
    usb usb5: SerialNumber: 0000:00:1d.1
    usb usb5: configuration #1 chosen from 1 choice
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
    usb 3-2: new full speed USB device using uhci_hcd and address 2
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: UHCI Host Controller
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
    uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b480
    usb usb6: new device found, idVendor=0000, idProduct=0000
    usb usb6: new device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb6: Product: UHCI Host Controller
    usb usb6: Manufacturer: Linux 2.6.22.18-0.2-default uhci_hcd
    usb usb6: SerialNumber: 0000:00:1d.2
    usb usb6: configuration #1 chosen from 1 choice
    hub 6-0:1.0: USB hub found
    hub 6-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1a.7 to 64
    ehci_hcd 0000:00:1a.7: EHCI Host Controller
    ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7
    ehci_hcd 0000:00:1a.7: debug port 1
    PCI: cache line size of 32 is not supported by device 0000:00:1a.7
    ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9fffc00
    usb 3-2: new device found, idVendor=046d, idProduct=0928
    ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb7: new device found, idVendor=0000, idProduct=0000
    usb usb7: new device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb7: Product: EHCI Host Controller
    usb usb7: Manufacturer: Linux 2.6.22.18-0.2-default ehci_hcd
    usb usb7: SerialNumber: 0000:00:1a.7
    usb usb7: configuration #1 chosen from 1 choice
    hub 7-0:1.0: USB hub found
    hub 7-0:1.0: 6 ports detected
    usb 3-2: new device strings: Mfr=1, Product=2, SerialNumber=0
    usb 3-2: Product: Camera
    usb 3-2: configuration #1 chosen from 1 choice
    usb 3-2: can't set config #1, error -71
    usb 1-2: USB disconnect, address 2
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    ehci_hcd 0000:00:1d.7: EHCI Host Controller
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
    ehci_hcd 0000:00:1d.7: debug port 1
    PCI: cache line size of 32 is not supported by device 0000:00:1d.7
    ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9fff800
    ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb8: new device found, idVendor=0000, idProduct=0000
    usb usb8: new device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb8: Product: EHCI Host Controller
    usb usb8: Manufacturer: Linux 2.6.22.18-0.2-default ehci_hcd
    usb usb8: SerialNumber: 0000:00:1d.7
    usb usb8: configuration #1 chosen from 1 choice
    hub 8-0:1.0: USB hub found
    hub 8-0:1.0: 6 ports detected
    usb 3-2: USB disconnect, address 2
    usbcore: registered new interface driver hiddev
    usb 3-2: new full speed USB device using uhci_hcd and address 3
    usb 3-2: new device found, idVendor=046d, idProduct=0928
    usb 3-2: new device strings: Mfr=1, Product=2, SerialNumber=0
    usb 3-2: Product: Camera
    usb 3-2: Manufacturer:
    usb 3-2: configuration #1 chosen from 1 choice
    usbcore: registered new interface driver usbhid
    drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
    Attempting manual resume
    usb 1-2: new low speed USB device using uhci_hcd and address 3
    kjournald starting.  Commit interval 5 seconds
    EXT3 FS on sda6, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    usb 1-2: new device found, idVendor=046d, idProduct=c045
    usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
    usb 1-2: Product: USB-PS/2 Optical Mouse
    usb 1-2: Manufacturer: Logitech
    usb 1-2: configuration #1 chosen from 1 choice
    input: Logitech USB-PS/2 Optical Mouse as /class/input/input2
    input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.0-2
    sd 2:0:0:0: Attached scsi generic sg0 type 0
    scsi 3:0:0:0: Attached scsi generic sg1 type 5
    sd 6:0:0:0: Attached scsi generic sg2 type 0
    Linux video capture interface: v2.00
    rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
    rtc_cmos: probe of 00:03 failed with error -16
    /usr/src/packages/BUILD/spca5xx-20060501/obj/default/drivers/usb/spca5xx.c: USB SPCA5XX camera found.Logitech QuickCam Express II(SPCA561A)
    /usr/src/packages/BUILD/spca5xx-20060501/obj/default/drivers/usb/spca5xx.c: [spca5xx_probe:5479] Camera type S561
    /usr/src/packages/BUILD/spca5xx-20060501/obj/default/drivers/usb/spca5xx.c: [spca5xx_getcapability:1764] maxw 352 maxh 288 minw 160 minh 120
    usbcore: registered new interface driver spca5xx
    /usr/src/packages/BUILD/spca5xx-20060501/obj/default/drivers/usb/spca5xx.c: spca5xx driver 00.60.00 registered
    sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 3:0:0:0: Attached scsi CD-ROM sr0
    input: Power Button (FF) as /class/input/input3
    ACPI: Power Button (FF) [PWRF]
    input: Power Button (CM) as /class/input/input4
    ACPI: Power Button (CM) [PWRB]
    b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
    ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:02:00.0 to 64
    atl1 0000:02:00.0: version 2.0.7
    flexcop-pci: will use the HW PID filter.
    flexcop-pci: card revision 1
    ACPI: PCI Interrupt 0000:05:02.0[A] -> GSI 18 (level, low) -> IRQ 18
    DVB: registering new adapter (FlexCop Digital TV device).
    b2c2-flexcop: MAC address = 00:d0:d7:01:5f:58
    b2c2-flexcop: found the stv0299 at i2c address: 0x68
    DVB: registering frontend 0 (ST STV0299 DVB-S)...
    b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by a 'FlexCopII' complete
    ACPI: PCI Interrupt 0000:05:03.0[A] -> GSI 16 (level, low) -> IRQ 16
    nvidia: module license 'NVIDIA' taints kernel.
    ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]  MMIO=[febef800-febeffff]  Max Packet=[2048]  IR/IT contexts=[4/8]
    ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
    ALSA sound/pci/hda/hda_codec.c:2333: autoconfig: line_outs=4 (0x14/0x15/0x16/0x17/0x0)
    ALSA sound/pci/hda/hda_codec.c:2337:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
    ALSA sound/pci/hda/hda_codec.c:2341:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
    ALSA sound/pci/hda/hda_codec.c:2349:    inputs: mic=0x18, fmic=0x19, line=0x1a, fline=0x0, cd=0x0, aux=0x0
    ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:01:00.0 to 64
    NVRM: loading NVIDIA UNIX x86_64 Kernel Module  173.14.05  Mon May 19 00:03:22 PDT 2008
    usbcore: registered new interface driver gspca
    /usr/src/packages/BUILD/gspcav1-20070110/obj/default/gspca_core.c: gspca driver 01.00.12 registered
    Adding 10487196k swap on /dev/sda5.  Priority:-1 extents:1 across:10487196k
    device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
    ieee1394: Host added: ID:BUS[0-00:1023]  GUID[001e8c000112cba6]
    loop: module loaded
    kjournald starting.  Commit interval 5 seconds
    EXT3 FS on sda7, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    AppArmor: AppArmor initialized
    audit(1213900577.792:2):  type=1505 info="AppArmor initialized" pid=2275
    coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
    coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
    coretemp coretemp.2: Using undocumented features, absolute temperature might be wrong!
    coretemp coretemp.3: Using undocumented features, absolute temperature might be wrong!
    atl1 0000:02:00.0: eth0 link is up 100 Mbps full duplex
    ip6_tables: (C) 2000-2006 Netfilter Core Team
    IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
    ip_tables: (C) 2000-2006 Netfilter Core Team
    audit(1213893397.256:3): audit_backlog_limit=320 old=64 by auid=4294967295 res=1
    audit(1213893397.312:4): audit_pid=3717 old=0 by auid=4294967295
    Danke für jeden Hinweis

    michel_vaclav
    Geändert von michel_vaclav (19.06.08 um 20:44 Uhr) Grund: Tippfehler beseitigt

  2. #2
    on the run
    Registriert seit
    May 2004
    Beiträge
    536
    Versuch mal unter -> Einstellungen -> Xine-Parameter -> Video -> xshm Driver einzustellen.

    cu talcid
    Kubuntu 9.10 und SuSE 11.2

    Terroristen haben kein Gewissen, da sie meinen, das Gewissen zu sein. Friedrich Hacker

  3. #3
    Registrierter Benutzer Avatar von michel_vaclav
    Registriert seit
    Jan 2003
    Ort
    daheim
    Beiträge
    1.052
    Zitat Zitat von talcid Beitrag anzeigen
    Versuch mal unter -> Einstellungen -> Xine-Parameter -> Video -> xshm Driver einzustellen.
    Hallo talcid,

    leider keine Verbesserung.

    trotzdem danke

    michel_vaclav

  4. #4
    Drachir Avatar von Teetrinker
    Registriert seit
    Jan 2000
    Ort
    Hagen
    Beiträge
    1.007
    Mir ist das Problem:

    "Fehlerbild: Auf manchen Sendern (nicht alle!) stottert der Ton gleich von Beginn an, nach einigen Sekunden bilden sich Klötzchen, bis das Bild zeitweise komplett einfriert."

    jetzt kürzlich auch aufgefallen. Wollte Fußball(ZDF oder ARD) schauen und hatte das gleiche Problem. Habe eins der letzten libxine Updates unter openSUS 10.3 in Verdacht, oder ARD/ZDF & CO haben etwas geändert? Bin dann auf VLC ausgewichen - wollte erst mal Fußball schauen . Libxine-dvb brauchst du für Kaffeine nicht.
    Geändert von Teetrinker (19.06.08 um 20:59 Uhr)
    Spielt mehr Go
    http://playgo.to/interactive/german/ (Go -Einführung)
    http://www.gokgs.com/ (Go-Server)
    https://www.dgob.de/ (Deutscher Go-Bund)

  5. #5
    Registrierter Benutzer Avatar von michel_vaclav
    Registriert seit
    Jan 2003
    Ort
    daheim
    Beiträge
    1.052
    Hallo,

    ich seh gerade, dass auf Packman neue Versionen von kaffeine und libxine angeboten werden.
    Libxine behebt den fehler nicht, kaffeine ist erst in einer Stunde auf den Servern. Ich schau später noch mal, jetzt muss ich erst mal klassisch mit Fernseher D gegen P gucken.

    Danke erstmal

    michel_vaclav

  6. #6
    Registrierter Benutzer Avatar von michel_vaclav
    Registriert seit
    Jan 2003
    Ort
    daheim
    Beiträge
    1.052
    Hallo nochmals,

    nachdem Deutschland jetzt gewonnen hat, habe ich alles nochmals deinstalliert und die Versionen der DVD genommen. Damit gehts.

    Scheinbar ist in einem der Pakete von Packman tatsächlich was faul. Dank Teetrinker die Idee zur Lösung.

    Werde morgen mal die neuen Pakete von Packman probieren.

    Gute Nacht

    michel_vaclav

  7. #7
    on the run
    Registriert seit
    May 2004
    Beiträge
    536
    Auch mit den neuen Paketen läuft es nicht gut. Hoffentlich wird das Problem bald behoben.

    cu talcid
    Kubuntu 9.10 und SuSE 11.2

    Terroristen haben kein Gewissen, da sie meinen, das Gewissen zu sein. Friedrich Hacker

  8. #8
    Registrierter Benutzer
    Registriert seit
    Aug 2003
    Beiträge
    245
    Derweil xine benutzen und eine channels.conf mit scan erstmal herstellen und diese in .xine kopieren.
    Damit geht es vorerst auch wenn Kaffeine natürlich mit seiner Aufnahmefunktion ziemlich gut ist.
    Da nützt einem xine nicht so viel.
    Besonders wenn man in seinem Kaffeine seine ganzen Aufnahmen geplant hat.


    Update:
    Das neue libxine hat anscheined nur Probleme wenn das Fernsehprogramm mehrere Audioformate unterstützt. Das ZDF und der Bayrische Rundfunk hier in München z. B. senden in unterschiedlichen Audioformaten. Bei Sendern die ihr Audioformat nicht ändern tritt kein Fehler auf. Also entweder ein Containerproblem oder es liegt am Audiocodec.
    Geändert von Colamix (21.06.08 um 06:19 Uhr)

  9. #9
    on the run
    Registriert seit
    May 2004
    Beiträge
    536
    Packman hat eine neue libxine gebaut - damit ist bei mir das Problem behoben.

    cu talcid
    Kubuntu 9.10 und SuSE 11.2

    Terroristen haben kein Gewissen, da sie meinen, das Gewissen zu sein. Friedrich Hacker

  10. #10
    Registrierter Benutzer Avatar von michel_vaclav
    Registriert seit
    Jan 2003
    Ort
    daheim
    Beiträge
    1.052
    Zitat Zitat von talcid Beitrag anzeigen
    Packman hat eine neue libxine gebaut - damit ist bei mir das Problem behoben.
    Kann ich bestätigen.

    Danke

    michel_vaclav

  11. #11
    Registrierter Benutzer
    Registriert seit
    Feb 2005
    Beiträge
    161
    Hallo zusammen,

    dieser Beitrag ist zwar schon eine weile her, aber egal. Zu meinem Problem: ich benutze Suse11.1 und eine Skystar2 PCI Tv-Karte. Ich schaffe es einfach nicht, die Karte zum Laufen zu bekommen. Im Yast unter TV-Karten erscheint sie als "0-DVB B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card". Libxine, w32-codecs usw. ist installiert. Aber ich bekomme unter Kaffeine einfach keine Bilder zu sehen. Wenn ich auf bearbeiten gehe und einen Tuner auswählen möchte, bekomme ich die Meldung, dass kein Tuner vorhanden ist. Was muß ich da noch alles installieren ? Wer kann mir bitte weiterhelfen ????????

  12. #12
    on the run
    Registriert seit
    May 2004
    Beiträge
    536
    Hallo testing,

    ist das Paket dvb installiert?

    cu talcid
    Kubuntu 9.10 und SuSE 11.2

    Terroristen haben kein Gewissen, da sie meinen, das Gewissen zu sein. Friedrich Hacker

  13. #13
    Registrierter Benutzer
    Registriert seit
    Feb 2005
    Beiträge
    161
    Muß ich mal nachschauen. Ich möchte eigentlich über meine Satelittenschüßel Astra anschauen............

    Also, das Paket DVB ist nun auch installiert, aber immer noch nichts zu sehen. Was muß ich noch alles einstellen, bzw. installieren und ändern, damit ich endlich mal fernsehen kann.......
    Geändert von testing (16.05.09 um 11:40 Uhr)

  14. #14
    Registrierter Benutzer Avatar von michel_vaclav
    Registriert seit
    Jan 2003
    Ort
    daheim
    Beiträge
    1.052
    Und Du hast schon unter DVB-Einstellungen für den LNB1 Astra ausgewählt?

    michel_vaclav

  15. #15
    Registrierter Benutzer
    Registriert seit
    Feb 2005
    Beiträge
    161
    Ja, aber beim Sendersuchlauf findet er nichts...........................
    Astra 19.2E kann man da einstellen.

    Wenn ich folgenden Befehl in der Konsole als root eingebe passiert folgendes:

    rcvdr start
    Starting Video Disk Recorder openvt: vt 9 is in use; command aborted
    use `openvt -f' to force.
    Geändert von testing (17.05.09 um 21:00 Uhr)

Ähnliche Themen

  1. DVB und Kaffeine
    Von MoDuL im Forum Fernsehen
    Antworten: 12
    Letzter Beitrag: 16.03.07, 22:14
  2. DVB-T und Videolan
    Von clumsy im Forum Fernsehen
    Antworten: 5
    Letzter Beitrag: 31.05.06, 18:40
  3. Antworten: 2
    Letzter Beitrag: 24.11.05, 11:43
  4. xine stürzt nach videostart mit SIGSEGV ab
    Von -=eagle=- im Forum Anwendungen Allgemein, Software
    Antworten: 2
    Letzter Beitrag: 07.06.05, 19:41
  5. Mandrake 10.0 und Kaffeine ?
    Von tost im Forum Musik
    Antworten: 6
    Letzter Beitrag: 23.08.04, 13:06

Lesezeichen

Berechtigungen

  • Neue Themen erstellen: Nein
  • Themen beantworten: Nein
  • Anhänge hochladen: Nein
  • Beiträge bearbeiten: Nein
  •