Hallo,
Ich habe Probleme mein WLan stick mit wpa_supplicant zum laufen zu bekommen.
Meine wlankarte mit dmesg/lsusb:
Code:
dmesg des wlan sticks:
68.192193] eth0: no IPv6 routers present
[ 75.858427] usb 4-1: USB disconnect, device number 2
[ 81.752281] usb 1-3: new high-speed USB device number 3 using ehci_hcd
[ 81.886275] usb 1-3: New USB device found, idVendor=0bda, idProduct=a811
[ 81.886284] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 81.886292] usb 1-3: Product: 802.11ac WLAN Adapter
[ 81.886297] usb 1-3: Manufacturer: Realtek
[ 81.886302] usb 1-3: SerialNumber: 00e04c000001
# lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0bda:a811 Realtek Semiconductor Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
/etc/wpa_supplikant/wpa_supplikant.conf
Code:
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1
network={
id_str="wlan0"
scan_ssid=1
key_mgmt=WPA-PSK
proto=WPA
pairwise=TKIP
group=TKIP
ssid="meine-ssid"
#psk="abcdefg"
psk=c37298a418889af819b9f52efe5000989a54c9e5717c06dbcbe48c3292eebdaa
}
Die psk wurde wie folgt erstellt (hier mit meine-ssid und abcdefgh:
Code:
# wpa_passphrase meine-ssid
# reading passphrase from stdin
abcdefgh
network={
ssid="meine-ssid"
#psk="abcdefgh"
psk=c37298a418889af819b9f52efe5000989a54c9e5717c06dbcbe48c3292eebdaa
/etc/network/interfaces
Code:
auto lo
iface lo inet loopback
# The primary network interface
#allow-hotplug eth0
#iface eth0 inet dhcp
auto eth0
iface eth0 inet static
address 192.168.1.254
netmask 255.255.255.0
gateway 192.168.1.1
iface wlan0 inet dhcp
wpa-driver wext
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
Mit einem neustart der Interfaces:
# /etc/init.d/networking restart
[warn] Running /etc/init.d/networking restart is deprecated because it may not re-enable some interfaces ... (warning).
[....] Reconfiguring network interfaces...Stopping Avahi mDNS/DNS-SD Daemon: avahi-daemon.
done.
ifconfig sagt:
Code:
# ifconfig
eth0 Link encap:Ethernet HWaddr 2c:76:8a:ab:d3:9b
inet addr:192.168.2.254 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::2e76:8aff:feab:d39b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:376 errors:0 dropped:0 overruns:0 frame:0
TX packets:317 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:35862 (35.0 KiB) TX bytes:56663 (55.3 KiB)
Interrupt:18
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Folgendes bewirkt auch nix:
Code:
ifup wlan0, wpa_supplicant
Ignoring unknown interface wlan0,=wlan0,.
Ignoring unknown interface wpa_supplicant=wpa_supplicant.
Code:
# ifup --force wlan0
wpa_supplicant: wpa-roam can only be used with the "manual" inet METHOD
run-parts: /etc/network/if-pre-up.d/wpasupplicant exited with return code 1
Internet Systems Consortium DHCP Client 4.2.2
Copyright 2004-2011 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Cannot find device "wlan0"
Bind socket to interface: No such device
Failed to bring up wlan0.
Lesezeichen