Huhu.
Eins vorab. Achtung multipost:
http://www.linux-forum.de/hilfe-bumb...a-2123266.html
Allerdings vermute ich, dass ich dort onehin keine Antwort bekommen werde.
---
Da es bei Rechnern mit nvidias optimus technologie nicht möglich zu sein scheint, die eingebaute Intel Karte zu deaktivieren (was mir lieber wäre), versuche ich mich an der Bumblebee installation. Leider mehr schlecht als recht ...
Verbaut sind in meinem Acer 5742G ein Intel i5 und eine geforce gt540m.
Der i5 hat eine eingebaute Intel Grafikkarte.
Ahja, Betriebssystem ist Debian 6.0 (Linux smurflaptop 2.6.32-5-amd64 #1 SMP Sat Mar 31 04:00:05 UTC 2012 x86_64 GNU/Linux)
Bei der installation habe ich mich an dieses Howto gehalten:
http://wiki.debian.org/Bumblebee
also die bumblebee tar.gz runtergeladen
- bbswitch installiert
- virtual gl installiert
- dann den nvidia Treiber installiert
- hierzu nvidia-glx und nvidia-kernel-dkms mittels synaptic installiert und den Befehl
Code:
apt-get install -t squeeze-backports nvidia-glx linux-headers-$(uname -r) nvidia-kernel-dkms
ausgeführt.
Es gab keine Fehlermeldung. Aber jetzt mein Problem.
Das im folgenden als wichtig beschriebene schlägt fehl:
The following command is very important, if you skip it you will loose 3D acceleration. Restore Mesa as the default GL library since the primary display is running on the Intel graphics card:
Dieser Befehl wirft (auch nach einem neustart) folgenden Fehler aus:
Code:
root@smurflaptop:/usr/lib# update-alternatives --set glx /usr/lib/mesa-diverted
update-alternatives: Fehler: Keine Alternativen für glx.
Bitte um Hilfe
Laut hwinfo sieht es so aus, als wäre die installation des nvidia Treibers erfolgreich gewesen:
28: PCI 100.0: 0300 VGA compatible controller (VGA)
UDI: /org/freedesktop/Hal/devices/pci_10de_df4
Unique ID: VCu0.W9qWnR1aW29
Parent ID: vSkL.v_+I6xiKU82
SysFS ID: /devices/pci0000:00/0000:00:01.0/0000:01:00.0
SysFS BusID: 0000:01:00.0
Hardware Class: graphics card
Model: "nVidia VGA compatible controller"
Vendor: pci 0x10de "nVidia Corporation"
Device: pci 0x0df4
SubVendor: pci 0x1025 "Acer Incorporated "
SubDevice: pci 0x0488
Revision: 0xa1
Driver: "nvidia"
Driver Modules: "nvidia"
Memory Range: 0xd0000000-0xd0ffffff (rw,non-prefetchable)
Memory Range: 0xa0000000-0xafffffff (rw,prefetchable)
Memory Range: 0xb0000000-0xb1ffffff (rw,prefetchable)
I/O Ports: 0x3000-0x3fff (rw)
Memory Range: 0xd1000000-0xd107ffff (ro,prefetchable,disabled)
IRQ: 16 (67 events)
Module Alias: "pci:v000010DEd00000DF4sv00001025sd00000488bc03sc0 0i00"
Driver Info #0:
Driver Status: nvidiafb is not active
Driver Activation Cmd: "modprobe nvidiafb"
Driver Info #1:
Driver Status: nouveau is not active
Driver Activation Cmd: "modprobe nouveau"
Driver Info #2:
Driver Status: nvidia is active
Driver Activation Cmd: "modprobe nvidia"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #15 (PCI bridge)
Edit:
Hab jetzt nach dieser Beschreibung weitergemacht:
http://suwako.nomanga.net/
und Bumblebee nun installiert.
Beim ausführen von
Code:
optirun glxgears -info
erhaltei ch folgenden Fehler:
smurf@smurflaptop:~$ optirun glxgears -info
[ERROR]Cannot access secondary GPU - error: [XORG] (EE) Failed to load module "mouse" (module does not exist, 0)
[ERROR]Aborting because fallback start is disabled.
Welche Kleinigkeit habe ich übersehen?
Lesezeichen