debian: kein device-file fuer USB-Device

[Blackhawk]

Hallo Forum,

ich versuche gerade jemandem zu helfen, der hat Debian und kann kein Device-File fuer seine USB-Platte mounten.

Ausgabe lsusb:

Bus 002 Device 003: ID 058f:6362 Alcor Micro Corp.
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

Ausgabe /var/log/messages:

Mar 17 17:51:22 Basis kernel: usb 2-4: USB disconnect, address 2
Mar 17 17:51:23 Basis kernel: usb 2-3: new high speed USB device using ehci_hcd and address 4
Mar 17 17:51:23 Basis kernel: usb 2-3: configuration #1 chosen from 1 choice
Mar 17 17:51:23 Basis kernel: scsi6 : SCSI emulation for USB Mass Storage devices
Mar 17 17:51:28 Basis kernel:   Vendor: ST332062  Model: 0A                Rev: 0000
Mar 17 17:51:28 Basis kernel:   Type:   Direct-Access                      ANSI SCSI revision: 00
Mar 17 17:51:28 Basis kernel: SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
Mar 17 17:51:28 Basis kernel: sdb: Write Protect is off
Mar 17 17:51:28 Basis kernel: SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
Mar 17 17:51:28 Basis kernel: sdb: Write Protect is off
Mar 17 17:51:28 Basis kernel:  sdb: sdb1 sdb2 sdb3 sdb4
Mar 17 17:51:28 Basis kernel: sd 6:0:0:0: Attached scsi disk sdb

Leider gibt es kein device-File /dev/sdb*

Was soll ich tun?


edit:
Hier noch die Ausgabe von cat /proc/bus/usb/devices

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 8
B:  Alloc=  0/800 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.18-4-amd64 ehci_hcd
S:  Product=EHCI Host Controller
S:  SerialNumber=0000:00:0b.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=256ms

T:  Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  5 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=04b4 ProdID=6830 Rev= 0.01
S:  Manufacturer=Cypress Semiconductor
S:  Product=USB2.0 Storage Device
S:  SerialNumber=DEF107679C83
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

T:  Bus=02 Lev=01 Prnt=01 Port=07 Cnt=02 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=058f ProdID=6362 Rev= 1.00
S:  Manufacturer=Generic
S:  Product=Mass Storage Device
S:  SerialNumber=058F312D81B
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 8
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.18-4-amd64 ohci_hcd
S:  Product=OHCI Host Controller
S:  SerialNumber=0000:00:0b.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms

[gadget]

Mar 17 19:02:06 Laptop kernel: usb 2-3: new full speed USB device using ohci_hcd and address 6
Mar 17 19:02:07 Laptop kernel: usb 2-3: configuration #1 chosen from 1 choice
Mar 17 19:02:07 Laptop kernel: scsi2 : SCSI emulation for USB Mass Storage devices
Mar 17 19:02:11 Laptop kernel: scsi 2:0:0:0: Direct-Access     LG       USB Drive        1100 PQ: 0 ANSI: 0 CCS
Mar 17 19:02:11 Laptop kernel: sd 2:0:0:0: [sdb] 1971200 512-byte hardware sectors (1009 MB)
Mar 17 19:02:11 Laptop kernel: sd 2:0:0:0: [sdb] Write Protect is off
Mar 17 19:02:11 Laptop kernel: sd 2:0:0:0: [sdb] 1971200 512-byte hardware sectors (1009 MB)
Mar 17 19:02:12 Laptop kernel: sd 2:0:0:0: [sdb] Write Protect is off
Mar 17 19:02:12 Laptop kernel:  sdb: sdb1
Mar 17 19:02:12 Laptop kernel: sd 2:0:0:0: [sdb] Attached SCSI removable disk

Mehr Meldungen hat es bei mir auch nicht. Klingt ja fast unglaublich. Bei einem Newbie würde ich jetzt um die Ausgabe von ls /dev bitten

[Blackhawk]

Hat sich erledigt, da hat irgendein kernel-modul gefehlt, nach einem apt-get -s oder so macht er wieder device-files...