Usb Wlan Adapter unter Suse 10.3

**Aldebaran** · 14.02.08, 12:25

Hallo,

ich glaube ich bin zu böd um den Usb Wlan Adapter mit Zydas 1211 Chipsatz zum Laufen zu bringen!
Ich habe mir den Treiber von Suse installiert aber bekomme ihn unter Yast nicht Aktiviert ???
Wenn ich im Yast unter Hardware Hardware-Informationen nachschaue findet er ihn.
Warum nicht unter Netzwerkkarte.

Wer kann mir weiterhelfen....

cu

Uwe

**zyrusthc** · 14.02.08, 13:01

Hallo und Willkommen im Forum

Was sagt den:
lsusb
iwconfig
dmesg

Bitte verwende für die Ausgaben die CODE-Tags des Forums.

Greeez Oli

**Aldebaran** · 14.02.08, 13:14

Also folgende Meldungen :

lsusb

Bus 003 Device 017: ID 0ace:1215 ZyDAS
Bus 003 Device 002: ID 1058:0702 Western Digital Technologies, Inc.
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 002: ID 046d:c00e Logitech, Inc. M-BJ69 Optical Wheel Mouse
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

iwconfig

lo no wireless extensions.

eth0 no wireless extensions.

wlan0 no wireless extensions.

**Aldebaran** · 14.02.08, 13:20

dmesg

Code:

th0: Media Link On 100mbps full-duplex
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
NET: Registered protocol family 17
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
eth0: no IPv6 routers present
bootsplash: status on console 0 changed to on
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
eth0: no IPv6 routers present
usb 3-3: new high speed USB device using ehci_hcd and address 4
usb 3-3: new device found, idVendor=0ace, idProduct=1215
usb 3-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-3: Product: USB2.0 WLAN
usb 3-3: Manufacturer: ZyDAS
usb 3-3: configuration #1 chosen from 1 choice
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
usb 3-3: reset high speed USB device using ehci_hcd and address 4
usb 3-3: Could not load firmware file zd1211/zd1211b_ub. Error number -2
zd1211rw 3-3:1.0: couldn't load firmware. Error number -2
usb 3-3: reset high speed USB device using ehci_hcd and address 4
zd1211rw: probe of 3-3:1.0 failed with error -2
usbcore: registered new interface driver zd1211rw
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
usb 3-3: USB disconnect, address 4
eth0: no IPv6 routers present
usb 3-3: new high speed USB device using ehci_hcd and address 5
usb 3-3: new device found, idVendor=0ace, idProduct=1215
usb 3-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-3: Product: USB2.0 WLAN
usb 3-3: Manufacturer: ZyDAS
usb 3-3: configuration #1 chosen from 1 choice
usb 3-3: reset high speed USB device using ehci_hcd and address 5
usb 3-3: Could not load firmware file zd1211/zd1211b_ub. Error number -2
zd1211rw 3-3:1.0: couldn't load firmware. Error number -2
usb 3-3: reset high speed USB device using ehci_hcd and address 5
zd1211rw: probe of 3-3:1.0 failed with error -2
eth0: no IPv6 routers present
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
usb 3-3: USB disconnect, address 5
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
eth0: Media Link On 100mbps full-duplex
usb 3-3: new high speed USB device using ehci_hcd and address 6
usb 3-3: new device found, idVendor=0ace, idProduct=1215
usb 3-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-3: Product: USB2.0 WLAN
usb 3-3: Manufacturer: ZyDAS
usb 3-3: configuration #1 chosen from 1 choice
usb 3-3: reset high speed USB device using ehci_hcd and address 6
usb 3-3: Could not load firmware file zd1211/zd1211b_ub. Error number -2
zd1211rw 3-3:1.0: couldn't load firmware. Error number -2
usb 3-3: reset high speed USB device using ehci_hcd and address 6
zd1211rw: probe of 3-3:1.0 failed with error -2
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present

 _____     ____    _    ____
|__  /   _|  _ \  / \  / ___|
  / / | | | | | |/ _ \ \___ \
 / /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/   \_\____/
     |___/
ZD1211B - version 2.22.0.0-development
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
UW2453 RF
OverWrite CR157 = 0xF0
zd1205_config: EEP(HWFeature)=0x2000
AllowedChannel = 000107ff
Region:48
usbcore: registered new interface driver zd1211b
eth1 renamed to wlan0
udev: renamed network interface eth1 to wlan0

 _____     ____    _    ____
|__  /   _|  _ \  / \  / ___|
  / / | | | | | |/ _ \ \___ \
 / /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/   \_\____/
     |___/
zd1211 - version 2.22.0.0-development
usbcore: registered new interface driver zd1211
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
usb 3-3: USB disconnect, address 6
usb 3-3: new high speed USB device using ehci_hcd and address 7
usb 3-3: new device found, idVendor=0ace, idProduct=1215
usb 3-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-3: Product: USB2.0 WLAN
usb 3-3: Manufacturer: ZyDAS
usb 3-3: configuration #1 chosen from 1 choice
usb 3-3: reset high speed USB device using ehci_hcd and address 7
usb 3-3: Could not load firmware file zd1211/zd1211b_ub. Error number -2
zd1211rw 3-3:1.0: couldn't load firmware. Error number -2
usb 3-3: reset high speed USB device using ehci_hcd and address 7
zd1211rw: probe of 3-3:1.0 failed with error -2
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
UW2453 RF
OverWrite CR157 = 0xF0
zd1205_config: EEP(HWFeature)=0x2000
AllowedChannel = 000107ff
Region:48
eth1 renamed to wlan0
udev: renamed network interface eth1 to wlan0
eth0: no IPv6 routers present
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
RadioOn
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Set to CCK
Set to OFDM
wlan0: no IPv6 routers present
keybuf data [0]:

Just Update WEP key
eth0: Media Link On 100mbps full-duplex
keybuf data [0]:

Just Update WEP key
eth0: Media Link On 100mbps full-duplex
RadioOn
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Set to CCK
Set to OFDM
eth0: no IPv6 routers present
wlan0: no IPv6 routers present
RadioOn
******We Lose AP for 5 seconds
zd1205_notify_disjoin_event
RadioOn
keybuf data [0]:

Just Update WEP key
eth0: Media Link On 100mbps full-duplex
keybuf data [0]:

Just Update WEP key
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
usb 3-3: USB disconnect, address 7
usb 3-3: new high speed USB device using ehci_hcd and address 8
usb 3-3: new device found, idVendor=0ace, idProduct=1215
usb 3-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-3: Product: USB2.0 WLAN
usb 3-3: Manufacturer: ZyDAS
usb 3-3: configuration #1 chosen from 1 choice
usb 3-3: reset high speed USB device using ehci_hcd and address 8
usb 3-3: Could not load firmware file zd1211/zd1211b_ub. Error number -2
zd1211rw 3-3:1.0: couldn't load firmware. Error number -2
usb 3-3: reset high speed USB device using ehci_hcd and address 8
zd1211rw: probe of 3-3:1.0 failed with error -2
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
UW2453 RF
OverWrite CR157 = 0xF0
zd1205_config: EEP(HWFeature)=0x2000
AllowedChannel = 000107ff
Region:48
eth1 renamed to wlan0
udev: renamed network interface eth1 to wlan0
RadioOn
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Set to CCK
Set to OFDM
wlan0: no IPv6 routers present
******We Lose AP for 5 seconds
zd1205_notify_disjoin_event
Wrong @ zd1211_rx_comp_cb, status=-71(3286277).
nonzero read bulk status received: -EPROTO
usb 3-3: USB disconnect, address 8
ehci_hcd 0000:00:08.2: qh cd1bb380 (#82) state 4(has tds)

Error is xxx
zd1211: failed rx_urb
The following is only an harmless informational message.
Unless you get a _continuous_flood_ of these messages it means
everything is working fine. Allocations from irqs cannot be
perfectly reliable and the kernel is designed to handle that.
firefox-bin: page allocation failure. order:1, mode:0x20
 [<c0158462>] __alloc_pages+0x2c5/0x2d6
 [<c016de36>] cache_alloc_refill+0x2ae/0x4c1
 [<c016e0c0>] __kmalloc+0x77/0x8f
 [<c026c270>] __alloc_skb+0x4b/0x108
 [<c029a35c>] tcp_collapse+0x15a/0x34a
 [<c029a536>] tcp_collapse+0x334/0x34a
 [<c029a6a6>] tcp_prune_queue+0x15a/0x228
 [<c029a927>] tcp_data_queue+0x1b3/0xa76
 [<c011e038>] __wake_up+0x32/0x43
 [<c026d83d>] __skb_checksum_complete_head+0x18/0x58
 [<c029c928>] tcp_rcv_established+0x72a/0x7de
 [<c02c0d2c>] unix_stream_recvmsg+0x39f/0x49a
 [<c02a1868>] tcp_v4_do_rcv+0x2b/0x32e
 [<c02a3bc2>] tcp_v4_rcv+0x84c/0x8aa
 [<c028a8f9>] ip_local_deliver_finish+0x0/0x1b3
 [<c028b1b4>] ip_local_deliver+0x189/0x231
 [<c028a8f9>] ip_local_deliver_finish+0x0/0x1b3
 [<c028aff2>] ip_rcv+0x485/0x4be
 [<ceed0ebe>] packet_rcv_spkt+0x141/0x154 [af_packet]
 [<c027025f>] netif_receive_skb+0x2ef/0x309
 [<cf0e1df2>] sis900_interrupt+0x27d/0x60d [sis900]
 [<c0271ebd>] process_backlog+0x93/0x109
 [<c02720a8>] net_rx_action+0xa7/0x1b3
 [<c012930c>] __do_softirq+0x75/0xe1
 [<c01293bd>] do_softirq+0x45/0x53
 [<c0129621>] irq_exit+0x38/0x6b
 [<c0107486>] do_IRQ+0x7e/0x90
 [<c0105e73>] common_interrupt+0x23/0x30
 =======================
Mem-info:
DMA per-cpu:
CPU    0: Hot: hi:    0, btch:   1 usd:   0   Cold: hi:    0, btch:   1 usd:   0
Normal per-cpu:
CPU    0: Hot: hi:   90, btch:  15 usd:  73   Cold: hi:   30, btch:   7 usd:  25
Active:26553 inactive:17794 dirty:2394 writeback:0 unstable:0
 free:832 slab:8227 mapped:6011 pagetables:479 bounce:0
DMA free:876kB min:136kB low:168kB high:204kB active:5616kB inactive:3072kB present:16256kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 206 206
Normal free:2452kB min:1764kB low:2204kB high:2644kB active:100596kB inactive:68104kB present:211268kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 0 0
DMA: 73*4kB 1*8kB 0*16kB 0*32kB 1*64kB 0*128kB 0*256kB 1*512kB 0*1024kB 0*2048kB 0*4096kB = 876kB
Normal: 531*4kB 1*8kB 0*16kB 0*32kB 1*64kB 0*128kB 1*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 2452kB
Swap cache: add 500917, delete 483828, find 294083/376481, race 0+1
Free swap  = 1918880kB
Total swap = 2104472kB
Free swap:       1918880kB
57328 pages of RAM
0 pages of HIGHMEM
1419 reserved pages
40334 pages shared
17089 pages swap cached
2394 pages dirty
0 pages writeback
6011 pages mapped
8227 pages slab
479 pages pagetables
The following is only an harmless informational message.
Unless you get a _continuous_flood_ of these messages it means
everything is working fine. Allocations from irqs cannot be
perfectly reliable and the kernel is designed to handle that.
firefox-bin: page allocation failure. order:1, mode:0x20
 [<c0158462>] __alloc_pages+0x2c5/0x2d6
 [<c016de36>] cache_alloc_refill+0x2ae/0x4c1
 [<c016e0c0>] __kmalloc+0x77/0x8f
 [<c026c270>] __alloc_skb+0x4b/0x108
 [<c029a35c>] tcp_collapse+0x15a/0x34a
 [<c029a536>] tcp_collapse+0x334/0x34a
 [<c029a6a6>] tcp_prune_queue+0x15a/0x228
 [<c029a927>] tcp_data_queue+0x1b3/0xa76
 [<c011e038>] __wake_up+0x32/0x43
 [<c026d83d>] __skb_checksum_complete_head+0x18/0x58
 [<c029c928>] tcp_rcv_established+0x72a/0x7de
 [<c02c0d2c>] unix_stream_recvmsg+0x39f/0x49a
 [<c02a1868>] tcp_v4_do_rcv+0x2b/0x32e
 [<c02a3bc2>] tcp_v4_rcv+0x84c/0x8aa
 [<c028a8f9>] ip_local_deliver_finish+0x0/0x1b3
 [<c028b1b4>] ip_local_deliver+0x189/0x231
 [<c028a8f9>] ip_local_deliver_finish+0x0/0x1b3
 [<c028aff2>] ip_rcv+0x485/0x4be
 [<ceed0ebe>] packet_rcv_spkt+0x141/0x154 [af_packet]
 [<c027025f>] netif_receive_skb+0x2ef/0x309
 [<cf0e1df2>] sis900_interrupt+0x27d/0x60d [sis900]
 [<c0271ebd>] process_backlog+0x93/0x109
 [<c02720a8>] net_rx_action+0xa7/0x1b3
 [<c012930c>] __do_softirq+0x75/0xe1
 [<c01293bd>] do_softirq+0x45/0x53
 [<c0129621>] irq_exit+0x38/0x6b
 [<c0107486>] do_IRQ+0x7e/0x90
 [<c0105e73>] common_interrupt+0x23/0x30
 =======================
Mem-info:
DMA per-cpu:
CPU    0: Hot: hi:    0, btch:   1 usd:   0   Cold: hi:    0, btch:   1 usd:   0
Normal per-cpu:
CPU    0: Hot: hi:   90, btch:  15 usd:  79   Cold: hi:   30, btch:   7 usd:  23
Active:26630 inactive:16176 dirty:2404 writeback:0 unstable:0
 free:2212 slab:8404 mapped:6016 pagetables:472 bounce:0
DMA free:1024kB min:136kB low:168kB high:204kB active:5616kB inactive:2304kB present:16256kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 206 206
Normal free:7824kB min:1764kB low:2204kB high:2644kB active:100904kB inactive:62400kB present:211268kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 0 0
DMA: 252*4kB 0*8kB 1*16kB 0*32kB 0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 1024kB
Normal: 1876*4kB 0*8kB 0*16kB 0*32kB 1*64kB 0*128kB 1*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 7824kB
Swap cache: add 500982, delete 483828, find 294129/376537, race 0+1
Free swap  = 1918880kB
Total swap = 2104472kB
Free swap:       1918880kB
57328 pages of RAM
0 pages of HIGHMEM
1419 reserved pages
38356 pages shared
17154 pages swap cached
2404 pages dirty
0 pages writeback
6016 pages mapped
8404 pages slab
472 pages pagetables
The following is only an harmless informational message.
Unless you get a _continuous_flood_ of these messages it means
everything is working fine. Allocations from irqs cannot be
perfectly reliable and the kernel is designed to handle that.
Xorg: page allocation failure. order:1, mode:0x20
 [<c0158462>] __alloc_pages+0x2c5/0x2d6
 [<c016de36>] cache_alloc_refill+0x2ae/0x4c1
 [<c016e0c0>] __kmalloc+0x77/0x8f
 [<c026c270>] __alloc_skb+0x4b/0x108
 [<c029a35c>] tcp_collapse+0x15a/0x34a
 [<c029a536>] tcp_collapse+0x334/0x34a
 [<c029a6a6>] tcp_prune_queue+0x15a/0x228
 [<c029adb7>] tcp_data_queue+0x643/0xa76
 [<c011fccc>] default_wake_function+0x0/0xc
 [<c026d83d>] __skb_checksum_complete_head+0x18/0x58
 [<c029c928>] tcp_rcv_established+0x72a/0x7de
 [<c011fccc>] default_wake_function+0x0/0xc
 [<ceefd48b>] ipt_do_table+0x2bf/0x2e8 [ip_tables]
 [<c0288131>] ip_route_input+0x38/0xcae
 [<c011fccc>] default_wake_function+0x0/0xc
 [<c02a1868>] tcp_v4_do_rcv+0x2b/0x32e
 [<c02a3bc2>] tcp_v4_rcv+0x84c/0x8aa
 [<c028a8f9>] ip_local_deliver_finish+0x0/0x1b3
 [<c028b1b4>] ip_local_deliver+0x189/0x231
 [<c028a8f9>] ip_local_deliver_finish+0x0/0x1b3
 [<c028aff2>] ip_rcv+0x485/0x4be
 [<ceed0ebe>] packet_rcv_spkt+0x141/0x154 [af_packet]
 [<c027025f>] netif_receive_skb+0x2ef/0x309
 [<cf0e1df2>] sis900_interrupt+0x27d/0x60d [sis900]
 [<c0271ebd>] process_backlog+0x93/0x109
 [<c02720a8>] net_rx_action+0xa7/0x1b3
 [<c012930c>] __do_softirq+0x75/0xe1
 [<c01293bd>] do_softirq+0x45/0x53
 [<c0129621>] irq_exit+0x38/0x6b
 [<c0107486>] do_IRQ+0x7e/0x90
 [<c0105e73>] common_interrupt+0x23/0x30
 =======================
Mem-info:
DMA per-cpu:
CPU    0: Hot: hi:    0, btch:   1 usd:   0   Cold: hi:    0, btch:   1 usd:   0
Normal per-cpu:
CPU    0: Hot: hi:   90, btch:  15 usd:  57   Cold: hi:   30, btch:   7 usd:  20
Active:28107 inactive:17630 dirty:12388 writeback:2728 unstable:0
 free:384 slab:7295 mapped:7209 pagetables:472 bounce:0
DMA free:880kB min:136kB low:168kB high:204kB active:6316kB inactive:3012kB present:16256kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 206 206
Normal free:656kB min:1764kB low:2204kB high:2644kB active:106112kB inactive:67508kB present:211268kB pages_scanned:12131 all_unreclaimable? no
lowmem_reserve[]: 0 0 0
DMA: 18*4kB 1*8kB 0*16kB 3*32kB 1*64kB 1*128kB 0*256kB 1*512kB 0*1024kB 0*2048kB 0*4096kB = 880kB
Normal: 0*4kB 0*8kB 1*16kB 0*32kB 0*64kB 1*128kB 0*256kB 1*512kB 0*1024kB 0*2048kB 0*4096kB = 656kB
Swap cache: add 504056, delete 486781, find 345621/428776, race 0+1
Free swap  = 1920504kB
Total swap = 2104472kB
Free swap:       1920504kB
57328 pages of RAM
0 pages of HIGHMEM
1419 reserved pages
41098 pages shared
17275 pages swap cached
12388 pages dirty
2728 pages writeback
7209 pages mapped
7295 pages slab
472 pages pagetables
usb 3-3: new high speed USB device using ehci_hcd and address 9
usb 3-3: new device found, idVendor=0ace, idProduct=1215
usb 3-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-3: Product: USB2.0 WLAN
usb 3-3: Manufacturer: ZyDAS
usb 3-3: configuration #1 chosen from 1 choice
usb 3-3: reset high speed USB device using ehci_hcd and address 9
zd1211rw 3-3:1.0: RF UW2453_RF 0x9 is not supported
usb 3-3: reset high speed USB device using ehci_hcd and address 9
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
UW2453 RF
OverWrite CR157 = 0xF0
zd1205_config: EEP(HWFeature)=0x2000
AllowedChannel = 000107ff
Region:48
eth1 renamed to wlan0
udev: renamed network interface eth1 to wlan0
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
st: Version 20070203, fixed bufsize 32768, s/g segs 256
pnp: Device 00:08 disabled.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
lp0: using parport0 (polling).
pnp: Device 00:08 activated.
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
pnp: Device 00:08 disabled.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
ppa: Version 2.07 (for Linux 2.4.x)
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
usb 3-3: USB disconnect, address 9
usb 3-3: new high speed USB device using ehci_hcd and address 10
usb 3-3: new device found, idVendor=0ace, idProduct=1215
usb 3-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-3: Product: USB2.0 WLAN
usb 3-3: Manufacturer: ZyDAS
usb 3-3: configuration #1 chosen from 1 choice
usb 3-3: reset high speed USB device using ehci_hcd and address 10
zd1211rw 3-3:1.0: RF UW2453_RF 0x9 is not supported
usb 3-3: reset high speed USB device using ehci_hcd and address 10
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
UW2453 RF
OverWrite CR157 = 0xF0
zd1205_config: EEP(HWFeature)=0x2000
AllowedChannel = 000107ff
Region:48
eth1 renamed to wlan0
udev: renamed network interface eth1 to wlan0
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
spurious 8259A interrupt: IRQ7.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
pnp: Device 00:08 activated.
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
pnp: Device 00:08 disabled.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
ppa: Version 2.07 (for Linux 2.4.x)
usb 3-3: USB disconnect, address 10
usb 3-1: new high speed USB device using ehci_hcd and address 11
usb 3-1: new device found, idVendor=0ace, idProduct=1215
usb 3-1: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-1: Product: USB2.0 WLAN
usb 3-1: Manufacturer: ZyDAS
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: reset high speed USB device using ehci_hcd and address 11
zd1211rw 3-1:1.0: RF UW2453_RF 0x9 is not supported
usb 3-1: reset high speed USB device using ehci_hcd and address 11
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
UW2453 RF
OverWrite CR157 = 0xF0
zd1205_config: EEP(HWFeature)=0x2000
AllowedChannel = 000107ff
Region:48
eth1 renamed to wlan0
udev: renamed network interface eth1 to wlan0
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
usb 3-1: USB disconnect, address 11
usb 3-3: new high speed USB device using ehci_hcd and address 12
usb 3-3: new device found, idVendor=0ace, idProduct=1215
usb 3-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-3: Product: USB2.0 WLAN
usb 3-3: Manufacturer: ZyDAS
usb 3-3: configuration #1 chosen from 1 choice
usb 3-3: reset high speed USB device using ehci_hcd and address 12
zd1211rw 3-3:1.0: RF UW2453_RF 0x9 is not supported
usb 3-3: reset high speed USB device using ehci_hcd and address 12
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
UW2453 RF
OverWrite CR157 = 0xF0
zd1205_config: EEP(HWFeature)=0x2000
AllowedChannel = 000107ff
Region:48
eth1 renamed to wlan0
udev: renamed network interface eth1 to wlan0
usb 3-3: USB disconnect, address 12
usb 3-1: new high speed USB device using ehci_hcd and address 13
usb 3-1: new device found, idVendor=0ace, idProduct=1215
usb 3-1: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-1: Product: USB2.0 WLAN
usb 3-1: Manufacturer: ZyDAS
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: reset high speed USB device using ehci_hcd and address 13
zd1211rw 3-1:1.0: RF UW2453_RF 0x9 is not supported
usb 3-1: reset high speed USB device using ehci_hcd and address 13
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
UW2453 RF
OverWrite CR157 = 0xF0
zd1205_config: EEP(HWFeature)=0x2000
AllowedChannel = 000107ff
Region:48
eth1 renamed to wlan0
udev: renamed network interface eth1 to wlan0
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
eth0: no IPv6 routers present
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
usb 3-1: USB disconnect, address 13
usb 3-3: new high speed USB device using ehci_hcd and address 14
usb 3-3: new device found, idVendor=0ace, idProduct=1215
usb 3-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-3: Product: USB2.0 WLAN
usb 3-3: Manufacturer: ZyDAS
usb 3-3: configuration #1 chosen from 1 choice
usb 3-3: reset high speed USB device using ehci_hcd and address 14
zd1211rw 3-3:1.0: RF UW2453_RF 0x9 is not supported
usb 3-3: reset high speed USB device using ehci_hcd and address 14
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
UW2453 RF
OverWrite CR157 = 0xF0
zd1205_config: EEP(HWFeature)=0x2000
AllowedChannel = 000107ff
Region:48
eth1 renamed to wlan0
udev: renamed network interface eth1 to wlan0
eth0: Media Link On 100mbps full-duplex
eth0: Media Link On 100mbps full-duplex
eth0: no IPv6 routers present
usb 3-3: USB disconnect, address 14
usb 3-1: new high speed USB device using ehci_hcd and address 15
usb 3-1: new device found, idVendor=0ace, idProduct=1215
usb 3-1: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-1: Product: USB2.0 WLAN
usb 3-1: Manufacturer: ZyDAS
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: reset high speed USB device using ehci_hcd and address 15
zd1211rw 3-1:1.0: RF UW2453_RF 0x9 is not supported
usb 3-1: reset high speed USB device using ehci_hcd and address 15
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
UW2453 RF
OverWrite CR157 = 0xF0
zd1205_config: EEP(HWFeature)=0x2000
AllowedChannel = 000107ff
Region:48
eth1 renamed to wlan0
udev: renamed network interface eth1 to wlan0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
pnp: Device 00:08 activated.
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
pnp: Device 00:08 disabled.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
ppa: Version 2.07 (for Linux 2.4.x)
usb 3-1: USB disconnect, address 15
usb 3-3: new high speed USB device using ehci_hcd and address 16
usb 3-3: new device found, idVendor=0ace, idProduct=1215
usb 3-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-3: Product: USB2.0 WLAN
usb 3-3: Manufacturer: ZyDAS
usb 3-3: configuration #1 chosen from 1 choice
usb 3-3: reset high speed USB device using ehci_hcd and address 16
zd1211rw 3-3:1.0: RF UW2453_RF 0x9 is not supported
usb 3-3: reset high speed USB device using ehci_hcd and address 16
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
UW2453 RF
OverWrite CR157 = 0xF0
zd1205_config: EEP(HWFeature)=0x2000
AllowedChannel = 000107ff
Region:48
eth1 renamed to wlan0
udev: renamed network interface eth1 to wlan0
usb 3-3: USB disconnect, address 16
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
pnp: Device 00:08 activated.
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
pnp: Device 00:08 disabled.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
ppa: Version 2.07 (for Linux 2.4.x)
usb 3-3: new high speed USB device using ehci_hcd and address 17
usb 3-3: new device found, idVendor=0ace, idProduct=1215
usb 3-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 3-3: Product: USB2.0 WLAN
usb 3-3: Manufacturer: ZyDAS
usb 3-3: configuration #1 chosen from 1 choice
usb 3-3: reset high speed USB device using ehci_hcd and address 17
zd1211rw 3-3:1.0: RF UW2453_RF 0x9 is not supported
usb 3-3: reset high speed USB device using ehci_hcd and address 17
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
UW2453 RF
OverWrite CR157 = 0xF0
zd1205_config: EEP(HWFeature)=0x2000
AllowedChannel = 000107ff
Region:48
eth1 renamed to wlan0
udev: renamed network interface eth1 to wlan0

**zyrusthc** · 14.02.08, 13:29

Überarbeite deine Posts bitte mit den CODE-Tags des Forums, wie ich bereits in #2 gesagt hatte.

Code:

zd1211rw 3-3:1.0: couldn't load firmware. Error number -2

Wie siehts damit aus?!

Greeez Oli

Rain_maker · 14.02.08, 13:53

Lesestoff:

http://www.pc-forum24.de/suse-intern...ompendium.html

und

http://www.linuxforen.de/forums/showthread.php?t=247726

Vor allem die verlinkten Threads in linux-club.de

Und schmeiss den anderen, selbst gefrickelten Treiber raus.

Für openSUSE 10.3 musst Du zu 99% nichts von Hand kompilieren, das nur mal vorweg.

Greetz,

RM

**Aldebaran** · 14.02.08, 14:05

Und wie schmeiss ich die alten Treiber raus ???

Rain_maker · 14.02.08, 14:06

Suchen, finden, als root löschen.

Dateiname zd1211.ko oder zd1211b.ko und irgendwe in /lib/modules liegend.

Greetz,

RM

**zyrusthc** · 14.02.08, 14:07

Zitat von Aldebaran

Und wie schmeiss ich die alten Treiber raus ???

Einfach das Kernelmodul löschen!

Hast Du überhaupt meine Posts gelesen?!

Greeez Oli

**Aldebaran** · 14.02.08, 14:20

Hi Oli

hab dein Posts gelesen und geändert.
ich hoffe es ist so richtig ??

wie und wo Lösche ich das Kernel Modul ? über Yast ??

Rain_maker · 14.02.08, 14:44

WTF?

Als root die entsprechende Datei suchen und löschen, nix YaST.

Greetz,

RM

**zyrusthc** · 14.02.08, 15:12

Zitat von Aldebaran

wie und wo Lösche ich das Kernel Modul ?

Code:

rm -f $(find /lib/modules/`uname -r` -type f -name zd1211*)

Greeez Oli

Rain_maker · 14.02.08, 15:15

Dann ist der zd1211rw auch weg.

(Ist in dem Fall aber egal, weil die Version im 2.6.22er eh mit dem Stick nicht funktioniert.)

Greetz,

RM

**Aldebaran** · 14.02.08, 15:28

so alles gelöscht!

welchen Treiber soll ich nun am besten installieren den aus dem Forum oder das Open Suse Paket ?

cu

Uwe

Rain_maker · 14.02.08, 15:32

Am besten erst mal den "Infotreiber".

Denn ohne genaue Kernelversion und Architektur wird das zum Ratespiel.

Steht aber auch alles im ersten Link, den ich Dir gepostet habe.

Und "über RPM" wird so oder so die Antwort lauten, die Frage ist nur über welches.