heyho,
ich hab mir das open SuSE 10.2 zugelegt und freudig parallel zu XP installiert (erklärt mich nicht für verrückt, hat schon seine gründe ).
jedenfalls funktioniert die USB 2.0 HDD (freecom, 250GB, FAT32, kompatibel zu USB 1.1) unter XP und sogar dem guten alten DOS (+ubs treiber) einwandfrei, aber das Linux mag sie einfach nich, wobei sie doch unter 10.0 noch lief....
wenn die festplatte angeschlossen ist (egal ob schon beim start des OS oder erst nach vollständigem booten), wird sie in keiner weise erkannt und geht beständig wie ein metronom an und aus, das heißt etwa in nem 5-10 sek abstand.... any ideas? normal sein kann das wohl kaum
achja, fast hätte ich's vergessen: mein USB 2.0 brenner funktioniert und die festplatte geht auch an nem anderen usbport nicht im linux.
In den hardwareinformationen unter yast wird sie aufgeführt.
danke für jede hilfe und frohe weihnachten
gabs
PS: bitte nur antworten die mir bei meinem Problem weiterhelfen und keine überheblichen "schlauen" sprüche...
Anhang:
dmesg gibt folgendes aus:
sd 7:0:0:0: Attached scsi disk sda
sd 7:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 11
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi8 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 11
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 11
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 11
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 8:0:0:0: Attached scsi disk sda
sd 8:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 12
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi9 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 12
usb-storage: waiting for device to settle before scanning
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC= SRC=192.168.2.138 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=86
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 12
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 12
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 9:0:0:0: Attached scsi disk sda
sd 9:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 13
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi10 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 13
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 13
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 13
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 10:0:0:0: Attached scsi disk sda
sd 10:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 14
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi11 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 14
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 14
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 14
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 11:0:0:0: Attached scsi disk sda
sd 11:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 15
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi12 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 15
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 15
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 15
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 12:0:0:0: Attached scsi disk sda
sd 12:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 16
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi13 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 16
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 16
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 16
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 13:0:0:0: Attached scsi disk sda
sd 13:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 17
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi14 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 17
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 17
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 17
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 14:0:0:0: Attached scsi disk sda
sd 14:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 18
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi15 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 18
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 18
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 18
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 15:0:0:0: Attached scsi disk sda
sd 15:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 19
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi16 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 19
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 19
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 19
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 16:0:0:0: Attached scsi disk sda
sd 16:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 20
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi17 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 20
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 20
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 20
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 17:0:0:0: Attached scsi disk sda
sd 17:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 21
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi18 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 21
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 21
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 21
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 18:0:0:0: Attached scsi disk sda
sd 18:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 22
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi19 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 22
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 22
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 22
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 19:0:0:0: Attached scsi disk sda
sd 19:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 23
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi20 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 23
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 23
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=221.208.208.93 DST=192.168.2.138 LEN=485 TOS=0x00 PREC=0x00 TTL=51 ID=0 DF PROTO=UDP SPT=58860 DPT=1026 LEN=465
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 23
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 20:0:0:0: Attached scsi disk sda
sd 20:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 24
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi21 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 24
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 24
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 24
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 21:0:0:0: Attached scsi disk sda
sd 21:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 25
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi22 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 25
usb-storage: waiting for device to settle before scanning
Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
usb 4-5: reset high speed USB device using ehci_hcd and address 25
usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
usb 4-5: USB disconnect, address 25
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 22:0:0:0: Attached scsi disk sda
sd 22:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
usb 4-5: new high speed USB device using ehci_hcd and address 26
usb 4-5: device descriptor read/64, error -71
usb 4-5: new device found, idVendor=07ab, idProduct=fccd
usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: FHD-Classic
usb 4-5: Manufacturer: Freecom Technologies
usb 4-5: SerialNumber: 10000000000000002965A
usb 4-5: configuration #1 chosen from 1 choice
scsi23 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 26
usb-storage: waiting for device to settle before scanning
usb 4-3: USB disconnect, address 2
scsi 0:0:0:0: rejecting I/O to dead device
scsi 0:0:0:0: rejecting I/O to dead device
scsi 0:0:0:0: rejecting I/O to dead device
usb 4-3: new high speed USB device using ehci_hcd and address 27
st: Version 20050830, fixed bufsize 32768, s/g segs 256
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=60.12.194.3 DST=192.168.2.138 LEN=487 TOS=0x00 PREC=0x00 TTL=53 ID=0 DF PROTO=UDP SPT=46789 DPT=1026 LEN=467
cdrom: hdc: mrw address space DMA selected
pnp: Device 00:03 disabled.
parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
parport 0x378: You gave this address, but there is probably no parallel port there!
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
pnp: Device 00:03 activated.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
pnp: Device 00:03 disabled.
parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
parport 0x378: You gave this address, but there is probably no parallel port there!
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
ppa: Version 2.07 (for Linux 2.4.x)
cdrom: hdc: mrw address space DMA selected
cdrom: hdc: mrw address space DMA selected
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=60.11.125.55 DST=192.168.2.138 LEN=486 TOS=0x00 PREC=0x00 TTL=51 ID=0 DF PROTO=UDP SPT=48070 DPT=1026 LEN=466
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=204.16.210.50 DST=192.168.2.138 LEN=449 TOS=0x00 PREC=0x00 TTL=51 ID=0 DF PROTO=UDP SPT=52623 DPT=1026 LEN=429
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=202.97.238.199 DST=192.168.2.138 LEN=486 TOS=0x00 PREC=0x00 TTL=52 ID=0 DF PROTO=UDP SPT=51650 DPT=1026 LEN=466
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=221.208.208.90 DST=192.168.2.138 LEN=487 TOS=0x00 PREC=0x00 TTL=51 ID=0 DF PROTO=UDP SPT=40889 DPT=1026 LEN=467
SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=221.208.208.90 DST=192.168.2.138 LEN=487 TOS=0x00 PREC=0x00 TTL=51 ID=0 DF PROTO=UDP SPT=40891 DPT=1026 LEN=467
zu diesem Zeitpunkt hat die HDD sich mehrfach an und ausgestellt und ist schließlichgänzlich aus.
Lesezeichen