Anzeige:
Ergebnis 1 bis 3 von 3

Thema: suse 10.2 vs. USB HDD

  1. #1
    Registrierter Benutzer Avatar von gabs
    Registriert seit
    Dec 2006
    Ort
    Neuenstein
    Beiträge
    29

    suse 10.2 vs. USB HDD

    heyho,

    ich hab mir das open SuSE 10.2 zugelegt und freudig parallel zu XP installiert (erklärt mich nicht für verrückt, hat schon seine gründe ).
    jedenfalls funktioniert die USB 2.0 HDD (freecom, 250GB, FAT32, kompatibel zu USB 1.1) unter XP und sogar dem guten alten DOS (+ubs treiber) einwandfrei, aber das Linux mag sie einfach nich, wobei sie doch unter 10.0 noch lief....
    wenn die festplatte angeschlossen ist (egal ob schon beim start des OS oder erst nach vollständigem booten), wird sie in keiner weise erkannt und geht beständig wie ein metronom an und aus, das heißt etwa in nem 5-10 sek abstand.... any ideas? normal sein kann das wohl kaum
    achja, fast hätte ich's vergessen: mein USB 2.0 brenner funktioniert und die festplatte geht auch an nem anderen usbport nicht im linux.
    In den hardwareinformationen unter yast wird sie aufgeführt.
    danke für jede hilfe und frohe weihnachten

    gabs

    PS: bitte nur antworten die mir bei meinem Problem weiterhelfen und keine überheblichen "schlauen" sprüche...


    Anhang:
    dmesg gibt folgendes aus:

    sd 7:0:0:0: Attached scsi disk sda
    sd 7:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 11
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi8 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 11
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 11
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 11
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 8:0:0:0: Attached scsi disk sda
    sd 8:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 12
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi9 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 12
    usb-storage: waiting for device to settle before scanning
    SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC= SRC=192.168.2.138 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=86
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 12
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 12
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 9:0:0:0: Attached scsi disk sda
    sd 9:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 13
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi10 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 13
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 13
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 13
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 10:0:0:0: Attached scsi disk sda
    sd 10:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 14
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi11 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 14
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 14
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 14
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 11:0:0:0: Attached scsi disk sda
    sd 11:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 15
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi12 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 15
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 15
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 15
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 12:0:0:0: Attached scsi disk sda
    sd 12:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 16
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi13 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 16
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 16
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 16
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 13:0:0:0: Attached scsi disk sda
    sd 13:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 17
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi14 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 17
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 17
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 17
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 14:0:0:0: Attached scsi disk sda
    sd 14:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 18
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi15 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 18
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 18
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 18
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 15:0:0:0: Attached scsi disk sda
    sd 15:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 19
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi16 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 19
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 19
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 19
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 16:0:0:0: Attached scsi disk sda
    sd 16:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 20
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi17 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 20
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 20
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 20
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 17:0:0:0: Attached scsi disk sda
    sd 17:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 21
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi18 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 21
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 21
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 21
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 18:0:0:0: Attached scsi disk sda
    sd 18:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 22
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi19 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 22
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 22
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 22
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 19:0:0:0: Attached scsi disk sda
    sd 19:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 23
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi20 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 23
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 23
    SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=221.208.208.93 DST=192.168.2.138 LEN=485 TOS=0x00 PREC=0x00 TTL=51 ID=0 DF PROTO=UDP SPT=58860 DPT=1026 LEN=465
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 23
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 20:0:0:0: Attached scsi disk sda
    sd 20:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 24
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi21 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 24
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 24
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 24
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 21:0:0:0: Attached scsi disk sda
    sd 21:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 25
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi22 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 25
    usb-storage: waiting for device to settle before scanning
    Vendor: HDS72252 Model: 5VLAT80 Rev: V36O
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
    usb 4-5: reset high speed USB device using ehci_hcd and address 25
    usb 4-5: failed to restore interface 0 altsetting 0 (error=-110)
    usb 4-5: USB disconnect, address 25
    sda: Write Protect is off
    sda: Mode Sense: 03 00 00 00
    sda: assuming drive cache: write through
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00
    sda : sense not available.
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sd 22:0:0:0: Attached scsi disk sda
    sd 22:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    usb 4-5: new high speed USB device using ehci_hcd and address 26
    usb 4-5: device descriptor read/64, error -71
    usb 4-5: new device found, idVendor=07ab, idProduct=fccd
    usb 4-5: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 4-5: Product: FHD-Classic
    usb 4-5: Manufacturer: Freecom Technologies
    usb 4-5: SerialNumber: 10000000000000002965A
    usb 4-5: configuration #1 chosen from 1 choice
    scsi23 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 26
    usb-storage: waiting for device to settle before scanning
    usb 4-3: USB disconnect, address 2
    scsi 0:0:0:0: rejecting I/O to dead device
    scsi 0:0:0:0: rejecting I/O to dead device
    scsi 0:0:0:0: rejecting I/O to dead device
    usb 4-3: new high speed USB device using ehci_hcd and address 27
    st: Version 20050830, fixed bufsize 32768, s/g segs 256
    SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=60.12.194.3 DST=192.168.2.138 LEN=487 TOS=0x00 PREC=0x00 TTL=53 ID=0 DF PROTO=UDP SPT=46789 DPT=1026 LEN=467
    cdrom: hdc: mrw address space DMA selected
    pnp: Device 00:03 disabled.
    parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
    parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
    parport 0x378: You gave this address, but there is probably no parallel port there!
    parport0: PC-style at 0x378 [PCSPP,TRISTATE]
    pnp: Device 00:03 activated.
    parport: PnPBIOS parport detected.
    parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
    lp0: using parport0 (interrupt-driven).
    pnp: Device 00:03 disabled.
    parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
    parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
    parport 0x378: You gave this address, but there is probably no parallel port there!
    parport0: PC-style at 0x378 [PCSPP,TRISTATE]
    ppa: Version 2.07 (for Linux 2.4.x)
    cdrom: hdc: mrw address space DMA selected
    cdrom: hdc: mrw address space DMA selected
    SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=60.11.125.55 DST=192.168.2.138 LEN=486 TOS=0x00 PREC=0x00 TTL=51 ID=0 DF PROTO=UDP SPT=48070 DPT=1026 LEN=466
    SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=204.16.210.50 DST=192.168.2.138 LEN=449 TOS=0x00 PREC=0x00 TTL=51 ID=0 DF PROTO=UDP SPT=52623 DPT=1026 LEN=429
    SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=202.97.238.199 DST=192.168.2.138 LEN=486 TOS=0x00 PREC=0x00 TTL=52 ID=0 DF PROTO=UDP SPT=51650 DPT=1026 LEN=466
    SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=221.208.208.90 DST=192.168.2.138 LEN=487 TOS=0x00 PREC=0x00 TTL=51 ID=0 DF PROTO=UDP SPT=40889 DPT=1026 LEN=467
    SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=00:e0:18:d1:ac:32:00:04:e2:8a:2d:4d:08:00 SRC=221.208.208.90 DST=192.168.2.138 LEN=487 TOS=0x00 PREC=0x00 TTL=51 ID=0 DF PROTO=UDP SPT=40891 DPT=1026 LEN=467

    zu diesem Zeitpunkt hat die HDD sich mehrfach an und ausgestellt und ist schließlichgänzlich aus.
    Geändert von gabs (22.12.06 um 20:23 Uhr)

  2. #2
    Registrierter Benutzer Avatar von happyhibo
    Registriert seit
    Jun 2006
    Beiträge
    11

    Angry so..so..

    so...

    ich habe nun das gleiche Problem...

    Nur bei Deinen schlauen "P.S:"-aussagen, braucht man sich nicht Wundern, das keiner Antwortet...

    openSuSe 10.2 - Medion 5400 - 1024MB
    SLES10 - Athlon 1200 - 1024MB
    Press any key to continue...
    Wo ist eigentlich die any-key-taste ?!

  3. #3
    Registrierter Benutzer Avatar von Stingray0481
    Registriert seit
    Dec 2000
    Ort
    Erlangen
    Beiträge
    1.198
    Benutzt man die Forumsuche z.B. mit dem Begriff "Freecom" liefert sie (derzeit) an vierter Stelle folgenden Thread:
    http://www.linuxforen.de/forums/show...hlight=freecom

    Die Entscheidung ob das nun ein überheblicher Spruch ist, oder dir bei der Problemlösung hilft, überlasse ich dir. ;-)
    Dell Latitude D820: Kubuntu (13.10)

Ähnliche Themen

  1. USB-Problem nach Installation Suse 10.1
    Von rblum im Forum System installieren und konfigurieren
    Antworten: 4
    Letzter Beitrag: 08.11.06, 23:22
  2. USB Stick hin???
    Von openpeppi im Forum stationäre Hardware
    Antworten: 2
    Letzter Beitrag: 17.09.06, 19:13
  3. Externe ext3 Patition kann nicht gemountet werden: Bad Superblock
    Von [HO]Xerxes im Forum System installieren und konfigurieren
    Antworten: 13
    Letzter Beitrag: 31.05.06, 20:53
  4. Hach... Usb-Floppy
    Von Zinnwurm im Forum stationäre Hardware
    Antworten: 15
    Letzter Beitrag: 23.11.04, 22:11
  5. Suse 9.1 bleibt hängen
    Von satfan im Forum System installieren und konfigurieren
    Antworten: 5
    Letzter Beitrag: 23.07.04, 10:20

Lesezeichen

Berechtigungen

  • Neue Themen erstellen: Nein
  • Themen beantworten: Nein
  • Anhänge hochladen: Nein
  • Beiträge bearbeiten: Nein
  •