Code:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2004.04.16 18:00:36 =~=~=~=~=~=~=~=~=~=~=~=
dmesg
ion 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M, fd1 is 1.2M
FDC 0 is an 8272A
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 16 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c586a (rev 27) IDE UDMA33 controller on pci00:07.1
ide0: BM-DMA at 0x6000-0x6007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x6008-0x600f, BIOS settings: hdc:pio, hdd:pio
hda: QUANTUM FIREBALL CX13.0A, ATA DISK drive
hdb: SAMSUNG SV1604N, ATA DISK drive
blk: queue c03ac0c0, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03ac214, I/O limit 4095Mb (mask 0xffffffff)
hdc: SAMSUNG SV1604N, ATA DISK drive
hdd: SAMSUNG SV1604N, ATA DISK drive
blk: queue c03ac540, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03ac694, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 25429824 sectors (13020 MB) w/418KiB Cache, CHS=12614/32/63, UDMA(33)
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 312581808 sectors (160042 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(33)
hdc: attached ide-disk driver.
hdc: host protected area => 1
hdc: 312581808 sectors (160042 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(33)
hdd: attached ide-disk driver.
hdd: host protected area => 1
hdd: 312581808 sectors (160042 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(33)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3
hdb: hdb1 < hdb5 >
hdc: hdc1 <hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
hdc5 >
hdd: hdd1 < hdd5 >
ide-floppy driver 0.99.newide
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
[events: 000000ca]
[events: 000000c8]
[events: 000000c8]
md: autorun ...
md: considering hdd5 ...
md: adding hdd5 ...
md: adding hdc5 ...
md: adding hdb5 ...
md: created md0
md: bind<hdb5,1>
md: bind<hdc5,2>
md: bind<hdd5,3>
md: running: <hdd5><hdc5><hdb5>
md: hdd5's event counter: 000000c8
md: hdc5's event counter: 000000c8
md: hdb5's event counter: 000000ca
md: superblock update time inconsistency -- using the most recent one
md: freshest: hdb5
md: kicking non-fresh hdd5 from array!
md: unbind<hdd5,2>
md: export_rdev(hdd5)
md: kicking non-fresh hdc5 from array!
md: unbind<hdc5,1>
md: export_rdev(hdc5)
md0: removing former faulty hdd5!
md0: removing former faulty hdc5!
md: md0: raid array is not clean -- starting background reconstruction
kmod: failed to exec /sbin/modprobe -s -k md-personality-4, errno = 2
md: personality 4 is not loaded!
md :do_md_run() returned -22
md: md0 stopped.
md: unbind<hdb5,0>
md: export_rdev(hdb5)
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 316k freed
VFS: Mounted root (ext2 filesystem).
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
VFS: Mounted root (ext2 filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 160k freed
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
blk: queue c03ac0c0, I/O limit 4095Mb (mask 0xffffffff)
hdb: DMA disabled
ide0: reset: success
[events: 000000ca]
[events: 000000c8]
[events: 000000c8]
md: autorun ...
md: considering hdc5 ...
md: adding hdc5 ...
md: adding hdd5 ...
md: adding hdb5 ...
md: created md0
md: bind<hdb5,1>
md: bind<hdd5,2>
md: bind<hdc5,3>
md: running: <hdc5><hdd5><hdb5>
md: hdc5's event counter: 000000c8
md: hdd5's event counter: 000000c8
md: hdb5's event counter: 000000ca
md: superblock update time inconsistency -- using the most recent one
md: freshest: hdb5
md: kicking non-fresh hdc5 from array!
md: unbind<hdc5,2>
md: export_rdev(hdc5)
md: kicking non-fresh hdd5 from array!
md: unbind<hdd5,1>
md: export_rdev(hdd5)
md0: removing former faulty hdd5!
md0: removing former faulty hdc5!
md: md0: raid array is not clean -- starting background reconstruction
raid5: measuring checksumming speed
8regs : 183.200 MB/sec
32regs : 130.400 MB/sec
pII_mmx : 254.800 MB/sec
p5_mmx : 310.000 MB/sec
raid5: using function: p5_mmx (310.000 MB/sec)
md: raid5 personality registered as nr 4
md0: max total readahead window set to 496k
md0: 2 data-disks, max readahead per data-disk: 248k
raid5: device hdb5 operational as raid disk 0
raid5: not enough operational devices for md0 (2/3 failed)
RAID5 conf printout:
--- rd:3 wd:1 fd:2
disk 0, s:0, o:1, n:0 rd:0 us:1 dev:hdb5
disk 1, s:0, o:0, n:1 rd:1 us:1 dev:[dev 00:00]
disk 2, s:0, o:0, n:2 rd:2 us:1 dev:[dev 00:00]
raid5: failed to run raid set md0
md: pers->run() failed ...
md :do_md_run() returned -22
md: md0 stopped.
md: unbind<hdb5,0>
md: export_rdev(hdb5)
md: ... autorun DONE.
md: Autodetecting RAID arrays.
[events: 000000c8]
[events: 000000c8]
[events: 000000ca]
md: could not import hdc5!
md: could not import hdd5!
md: could not import hdb5!
md: autorun ...
md: considering hdb5 ...
md: adding hdb5 ...
md: adding hdc5 ...
md: adding hdd5 ...
md: created md0
md: bind<hdd5,1>
md: bind<hdc5,2>
md: bind<hdb5,3>
md: running: <hdb5><hdc5><hdd5>
md: hdb5's event counter: 000000ca
md: hdc5's event counter: 000000c8
md: hdd5's event counter: 000000c8
md: superblock update time inconsistency -- using the most recent one
md: freshest: hdb5
md: kicking non-fresh hdc5 from array!
md: unbind<hdc5,2>
md: export_rdev(hdc5)
md: kicking non-fresh hdd5 from array!
md: unbind<hdd5,1>
md: export_rdev(hdd5)
md0: removing former faulty hdd5!
md0: removing former faulty hdc5!
md: md0: raid array is not clean -- starting background reconstruction
md0: max total readahead window set to 496k
md0: 2 data-disks, max readahead per data-disk: 248k
raid5: device hdb5 operational as raid disk 0
raid5: not enough operational devices for md0 (2/3 failed)
RAID5 conf printout:
--- rd:3 wd:1 fd:2
disk 0, s:0, o:1, n:0 rd:0 us:1 dev:hdb5
disk 1, s:0, o:0, n:1 rd:1 us:1 dev:[dev 00:00]
disk 2, s:0, o:0, n:2 rd:2 us:1 dev:[dev 00:00]
raid5: failed to run raid set md0
md: pers->run() failed ...
md :do_md_run() returned -22
md: md0 stopped.
md: unbind<hdb5,0>
md: export_rdev(hdb5)
md: ... autorun DONE.
LVM version 1.0.5+(mp-v6a)(22/07/2002) module loaded
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x84 { DriveStatusError BadCRC }
blk: queue c03ac540, I/O limit 4095Mb (mask 0xffffffff)
hdd: DMA disabled
ide1: reset: success
Adding Swap: 1048816k swap-space (priority 42)
sh-2006: reiserfs read_super_block: bread failed (dev 09:00, block 8, size 1024)
sh-2006: reiserfs read_super_block: bread failed (dev 09:00, block 64, size 1024)
sh-2021: reiserfs_read_super: can not find reiserfs on md(9,0)
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xc688f000, 00:e0:7d:8e:58:fb, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139B'
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
raw1394: /dev/raw1394 device initialized
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
Non-volatile memory driver v1.2
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
imm: Version 2.05 (for Linux 2.4.0)
ppa: Version 2.07 (for Linux 2.4.x)
WARNING - no ppa compatible devices found.
As of 31/Aug/1998 Iomega started shipping parallel
port ZIP drives with a different interface which is
supported by the imm (ZIP Plus) driver. If the
cable is marked with "AutoDetect", this is what has
happened.
lp0 off-line
end_request: I/O error, dev 02:00 (floppy), sector 0
end_request: I/O error, dev 02:00 (floppy), sector 0
end_request: I/O error, dev 02:01 (floppy), sector 0
md: Autodetecting RAID arrays.
[events: 000000c8]
[events: 000000c8]
[events: 000000ca]
md: autorun ...
md: considering hdb5 ...
md: adding hdb5 ...
md: adding hdd5 ...
md: adding hdc5 ...
md: created md0
md: bind<hdc5,1>
md: bind<hdd5,2>
md: bind<hdb5,3>
md: running: <hdb5><hdd5><hdc5>
md: hdb5's event counter: 000000ca
md: hdd5's event counter: 000000c8
md: hdc5's event counter: 000000c8
md: superblock update time inconsistency -- using the most recent one
md: freshest: hdb5
md: kicking non-fresh hdd5 from array!
md: unbind<hdd5,2>
md: export_rdev(hdd5)
md: kicking non-fresh hdc5 from array!
md: unbind<hdc5,1>
md: export_rdev(hdc5)
md0: removing former faulty hdd5!
md0: removing former faulty hdc5!
md: md0: raid array is not clean -- starting background reconstruction
md0: max total readahead window set to 496k
md0: 2 data-disks, max readahead per data-disk: 248k
raid5: device hdb5 operational as raid disk 0
raid5: not enough operational devices for md0 (2/3 failed)
RAID5 conf printout:
--- rd:3 wd:1 fd:2
disk 0, s:0, o:1, n:0 rd:0 us:1 dev:hdb5
disk 1, s:0, o:0, n:1 rd:1 us:1 dev:[dev 00:00]
disk 2, s:0, o:0, n:2 rd:2 us:1 dev:[dev 00:00]
raid5: failed to run raid set md0
md: pers->run() failed ...
md :do_md_run() returned -22
md: md0 stopped.
md: unbind<hdb5,0>
md: export_rdev(hdb5)
md: ... autorun DONE.
[events: 000000ca]
[events: 000000c8]
[events: 000000c8]
md: autorun ...
md: considering hdc5 ...
md: adding hdc5 ...
md: adding hdd5 ...
md: adding hdb5 ...
md: created md0
md: bind<hdb5,1>
md: bind<hdd5,2>
md: bind<hdc5,3>
md: running: <hdc5><hdd5><hdb5>
md: hdc5's event counter: 000000c8
md: hdd5's event counter: 000000c8
md: hdb5's event counter: 000000ca
md: superblock update time inconsistency -- using the most recent one
md: freshest: hdb5
md: kicking non-fresh hdc5 from array!
md: unbind<hdc5,2>
md: export_rdev(hdc5)
md: kicking non-fresh hdd5 from array!
md: unbind<hdd5,1>
md: export_rdev(hdd5)
md0: removing former faulty hdd5!
md0: removing former faulty hdc5!
md: md0: raid array is not clean -- starting background reconstruction
md0: max total readahead window set to 496k
md0: 2 data-disks, max readahead per data-disk: 248k
raid5: device hdb5 operational as raid disk 0
raid5: not enough operational devices for md0 (2/3 failed)
RAID5 conf printout:
--- rd:3 wd:1 fd:2
disk 0, s:0, o:1, n:0 rd:0 us:1 dev:hdb5
disk 1, s:0, o:0, n:1 rd:1 us:1 dev:[dev 00:00]
disk 2, s:0, o:0, n:2 rd:2 us:1 dev:[dev 00:00]
raid5: failed to run raid set md0
md: pers->run() failed ...
md :do_md_run() returned -22
md: md0 stopped.
md: unbind<hdb5,0>
md: export_rdev(hdb5)
md: ... autorun DONE.
[events: 000000ca]
[events: 000000c8]
[events: 000000c8]
md: autorun ...
md: considering hdc5 ...
md: adding hdc5 ...
md: adding hdd5 ...
md: adding hdb5 ...
md: created md0
md: bind<hdb5,1>
md: bind<hdd5,2>
md: bind<hdc5,3>
md: running: <hdc5><hdd5><hdb5>
md: hdc5's event counter: 000000c8
md: hdd5's event counter: 000000c8
md: hdb5's event counter: 000000ca
md: superblock update time inconsistency -- using the most recent one
md: freshest: hdb5
md: kicking non-fresh hdc5 from array!
md: unbind<hdc5,2>
md: export_rdev(hdc5)
md: kicking non-fresh hdd5 from array!
md: unbind<hdd5,1>
md: export_rdev(hdd5)
md0: removing former faulty hdd5!
md0: removing former faulty hdc5!
md: md0: raid array is not clean -- starting background reconstruction
md0: max total readahead window set to 496k
md0: 2 data-disks, max readahead per data-disk: 248k
raid5: device hdb5 operational as raid disk 0
raid5: not enough operational devices for md0 (2/3 failed)
RAID5 conf printout:
--- rd:3 wd:1 fd:2
disk 0, s:0, o:1, n:0 rd:0 us:1 dev:hdb5
disk 1, s:0, o:0, n:1 rd:1 us:1 dev:[dev 00:00]
disk 2, s:0, o:0, n:2 rd:2 us:1 dev:[dev 00:00]
raid5: failed to run raid set md0
md: pers->run() failed ...
md :do_md_run() returned -22
md: md0 stopped.
md: unbind<hdb5,0>
md: export_rdev(hdb5)
md: ... autorun DONE.
[events: 000000ca]
[events: 000000c8]
[events: 000000c8]
md: autorun ...
md: considering hdc5 ...
md: adding hdc5 ...
md: adding hdd5 ...
md: adding hdb5 ...
md: created md0
md: bind<hdb5,1>
md: bind<hdd5,2>
md: bind<hdc5,3>
md: running: <hdc5><hdd5><hdb5>
md: hdc5's event counter: 000000c8
md: hdd5's event counter: 000000c8
md: hdb5's event counter: 000000ca
md: superblock update time inconsistency -- using the most recent one
md: freshest: hdb5
md: kicking non-fresh hdc5 from array!
md: unbind<hdc5,2>
md: export_rdev(hdc5)
md: kicking non-fresh hdd5 from array!
md: unbind<hdd5,1>
md: export_rdev(hdd5)
md0: removing former faulty hdd5!
md0: removing former faulty hdc5!
md: md0: raid array is not clean -- starting background reconstruction
md0: max total readahead window set to 496k
md0: 2 data-disks, max readahead per data-disk: 248k
raid5: device hdb5 operational as raid disk 0
raid5: not enough operational devices for md0 (2/3 failed)
RAID5 conf printout:
--- rd:3 wd:1 fd:2
disk 0, s:0, o:1, n:0 rd:0 us:1 dev:hdb5
disk 1, s:0, o:0, n:1 rd:1 us:1 dev:[dev 00:00]
disk 2, s:0, o:0, n:2 rd:2 us:1 dev:[dev 00:00]
raid5: failed to run raid set md0
md: pers->run() failed ...
md :do_md_run() returned -22
md: md0 stopped.
md: unbind<hdb5,0>
md: export_rdev(hdb5)
md: ... autorun DONE.
linux:~ # exit
logout
Danke für Hilfe!!!
Lesezeichen