Wieso habe ich soviele Packet Fehler bei "ifconfig" in letzter Zeit?

[Desertfox]

Hier der Phpsysconfig Output:

Network Usage

Device Received Sent Err/Drop

eth0 3.58 GB 310.69 MB 8/0
eth1 2.00 GB 862.80 MB 11294/0
eth2 103.54 MB 1.13 GB 7055/0


Und Ifconfig Output:

eth0 Protokoll:Ethernet Hardware Adresse 00:A0:CC:5A:A1:37
inet Adresse:192.168.0.1 Bcast:192.168.0.255 Maske:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8389925 errors:1 dropped:0 overruns:0 frame:0
TX packets:10694262 errors:7 dropped:0 overruns:4 carrier:3
Kollisionen:0 SendewarteschlangenlÃ?nge:100
RX bytes:3838956316 (3661.1 Mb) TX bytes:325784491 (310.6 Mb)
Interrupt:5 Basisadresse:0x7000

eth1 Protokoll:Ethernet Hardware Adresse 00:E0:7D:93:A5:94
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:10583811 errors:0 dropped:0 overruns:0 frame:0
TX packets:12466359 errors:11296 dropped:0 overruns:0 carrier:22592
Kollisionen:55217 SendewarteschlangenlÃ?nge:100
RX bytes:2147937548 (2048.4 Mb) TX bytes:908834206 (866.7 Mb)
Interrupt:5 Basisadresse:0xf000

eth2 Protokoll:Ethernet Hardware Adresse 00:09:5B:2F:15:CF
inet Adresse:192.168.1.1 Bcast:192.168.1.255 Maske:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:696583 errors:0 dropped:0 overruns:0 frame:0
TX packets:1141803 errors:7055 dropped:0 overruns:0 carrier:0
Kollisionen:0 SendewarteschlangenlÃ?nge:100
RX bytes:109050470 (103.9 Mb) TX bytes:1230077065 (1173.0 Mb)
Interrupt:10 Basisadresse:0xd000 Speicher:e5000000-e5000fff

lo Protokoll:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:99410 errors:0 dropped:0 overruns:0 frame:0
TX packets:99410 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 SendewarteschlangenlÃ?nge:0
RX bytes:15941600 (15.2 Mb) TX bytes:15941600 (15.2 Mb)

ppp0 Protokoll:Punkt-zu-Punkt Verbindung
inet Adresse:217.236.174.26 P-z-P:217.5.98.183 Maske:255.255.255.255
UP PUNKTZUPUNKT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:18 errors:0 dropped:0 overruns:0 frame:0
TX packets:28 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 SendewarteschlangenlÃ?nge:3
RX bytes:1400 (1.3 Kb) TX bytes:2024 (1.9 Kb)





Eth1 ist an das ADSL Modem angeschlossen.
Eth0 an meinen 100mbit Switch.
Eth2 ist Wlan.

[Bauchi]

was sagt denn der output von mii-tool oder eth-tool ??
irgendwelche duplex probleme ?

[Desertfox]

[root@localhost xchat-2.0.5]# mii-tool
eth0: negotiated 100baseTx-FD, link ok
eth1: autonegotiation failed, link ok
SIOCGMIIPHY on 'eth2' failed: Operation not supported


[root@localhost xchat-2.0.5]# ethtool eth0
Settings for eth0:
No data available


[root@localhost xchat-2.0.5]# ethtool eth1
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised auto-negotiation: Yes
Speed: 10Mb/s
Duplex: Half
Port: MII
PHYAD: 32
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: d
Current message level: 0xffffffff (-1)
Link detected: yes


[root@localhost xchat-2.0.5]# ethtool eth2
Settings for eth2:
No data available