T-Dsl & Debian

Hallo,
ich habe auf meinem Rechner Debian unstable.
Nun habe ich versucht mit dem Debian pppoe Packet T-Dsl bei mir einzurichten. da das nicht funktioniert hat, habe ich es mit dem roaringpenguin.rpm (& alien) versucht. Ich weiß, dass die Verbindung von Netzwerkkarte zum Modem funktioniert, weil es bei Eintippen von

"pppoe -T20 -I eth1 -D pppoe.log"

keine Fehler gab. Wenn ich nun


pppd pty "/usr/sbin/pppoe -I eth1"

ausführe, startet sich pppd, geht aber gleich wieder mit exit heraus. Ich benutze übrigens PPPD 2.4f.


Ich hoffe ihr könnt mir helfen, da ich meinen konqueror in action vermisse. http://www.linuxforen.de/ubb/biggrin.gif

Ciao
mr_pope

wie sieht die pppoe.conf und die options datei im /etc/ppp verzeichnis aus ?

pppoe.conf:

#************************************************* **********************
#
# pppoe.conf
#
# Configuration file for rp-pppoe. Edit as appropriate and install in
# /etc/ppp/pppoe.conf
#
# NOTE: This file is used by the adsl-start, adsl-stop, adsl-connect and
# adsl-status shell scripts. It is *not* used in any way by the
# "pppoe" executable.
#
# Copyright (C) 2000 Roaring Penguin Software Inc.
#
# This file may be distributed under the terms of the GNU General
# Public License.
#
# $Id: pppoe.conf,v 1.6 2001/03/22 16:46:10 dfs Exp $
#************************************************* **********************

# When you configure a variable, DO NOT leave spaces around the "=" sign.

# Ethernet card connected to ADSL modem
ETH='eth0'

# ADSL user name. You may have to supply "@provider.com" Sympatico
# users in Canada do need to include "@sympatico.ca"
# Sympatico uses PAP authentication. Make sure /etc/ppp/pap-secrets
# contains the right username/password combination.
# For Magma, use xxyyzz@magma.ca
USER='xxx#0001@t-online.de'

# Bring link up on demand? Default is to leave link up all the time.
# If you want the link to come up on demand, set DEMAND to a number indicating
# the idle time after which the link is brought down.
DEMAND=no
#DEMAND=300

# DNS type: SERVER=obtain from server; SPECIFY=use DNS1 and DNS2;
# NOCHANGE=do not adjust.
DNSTYPE=SERVER

# Obtain DNS server addresses from the peer (recent versions of pppd only)
USEPEERDNS=yes

DNS1=
DNS2=

### ONLY TOUCH THE FOLLOWING SETTINGS IF YOU'RE AN EXPERT

# How long adsl-start waits for a new PPP interface to appear before
# concluding something went wrong. If you use 0, then adsl-start
# exits immediately with a successful status and does not wait for the
# link to come up. Time is in seconds.
#
# WARNING WARNING WARNING:
#
# If you are using rp-pppoe on a physically-inaccessible host, set
# CONNECT_TIMEOUT to 0. This makes SURE that the machine keeps trying
# to connect forever after adsl-start is called. Otherwise, it will
# give out after CONNECT_TIMEOUT seconds and will not attempt to
# connect again, making it impossible to reach.
CONNECT_TIMEOUT=30

# How often in seconds adsl-start polls to check if link is up
CONNECT_POLL=2

# Specific desired AC Name
ACNAME=

# Specific desired service name
SERVICENAME=

# Character to echo at each poll. Use PING="" if you don't want
# anything echoed
PING="."

# File where the adsl-connect script writes its process-ID.
# Three files are actually used:
# $PIDFILE contains PID of adsl-connect script
# $PIDFILE.pppoe contains PID of pppoe process
# $PIDFILE.pppd contains PID of pppd process
CF_BASE=`basename $CONFIG`
PIDFILE="/var/run/$CF_BASE-adsl.pid"

# Do you want to use synchronous PPP? "yes" or "no". "yes" is much
# easier on CPU usage, but may not work for you. It is safer to use
# "no", but you may want to experiment with "yes". "yes" is generally
# safe on Linux machines with the n_hdlc line discipline; unsafe on others.
SYNCHRONOUS=no

# Do you want to clamp the MSS? Here's how to decide:
# - If you have only a SINGLE computer connected to the ADSL modem, choose
# "no".
# - If you have a computer acting as a gateway for a LAN, choose "1412".
# The setting of 1412 is safe for either setup, but uses slightly more
# CPU power.
CLAMPMSS=1412
#CLAMPMSS=no

# LCP echo interval and failure count.
LCP_INTERVAL=20
LCP_FAILURE=3

# PPPOE_TIMEOUT should be about 4*LCP_INTERVAL
PPPOE_TIMEOUT=80

# Firewalling: One of NONE, STANDALONE or MASQUERADE
FIREWALL=NONE

# Linux kernel-mode plugin for pppd. If you want to try the kernel-mode
# plugin, use LINUX_PLUGIN=/etc/ppp/plugins/rp-pppoe.so
LINUX_PLUGIN=

# Any extra arguments to pass to pppoe. Normally, use a blank string
# like this:
PPPOE_EXTRA=""

# Rumour has it that "Citizen's Communications" with a 3Com
# HomeConnect ADSL Modem DualLink requires these extra options:
# PPPOE_EXTRA="-f 3c12:3c13 -S ISP"

# Any extra arguments to pass to pppd. Normally, use a blank string
# like this:
PPPD_EXTRA=""


optionsdatei:
# /etc/ppp/options

# Dial On Demand
#demand


connect /bin/true

ipcp-accept-remote
ipcp-accept-local

usepeerdns

idle 180

noipdefault

defaultroute


user "xxxxx#0001@t-online.de"
hide-password

noaccomp
nopcomp
novj
novjccomp
nobsdcomp
nodeflate
noccp

nocrtscts

local
noauth

lcp-echo-interval 10
lcp-echo-failure 3


lock

#debug

#nodetach

Falls es irgendeinem hilft bevor pppd exit meldet, gibt es "Serial Connection Established" aus.

[sprudel123]

ähm,.mag sein das ich falsch liege, aber musst du nicht auf das device ppp0 umleiten?
(ist jetzt so mal ganz aum bauch..)

[kaptain Iglo]

unter www.adsl4linux (http://www.adsl4linux) ist eine super Anleitung.

[chris-]

die TLD kannte ich noch gar nicht :p