maxxle
22.09.01, 15:58
Nachdem mein Mandrake 8.0 keine Autoerkennung und Einrichtung meiner AVM A1 non PnP-Karte unterstützt, hab ich mich an isdn4l versucht. Jetzt hab ich ein kleines Problem. Er kann den ISDN Controller nicht laden.
Mein Rechner sagt folgendes:
service isdn4linux restart
=>
Shutting down isdn4linux
Shutting down isdn/ippp devices (if any)
Unloading ISDN drivers ...
Starting ISDN for Linux...
Loading HiSax driver
CardID: HiSax
CardType: 5
CardName: AVM A1 (Fritz)
Parameters: id=HiSax type=5 protocol=2 irq=10 io=
Initialization of ISDN failed!
Check parameters in '/etc/sysconfig/isdn'!
Mich wundert ja nur, warum bei io= steht und nicht der Wert 240, so wie ich ihn auch hinterlegt habe in mycard ??
-------------------------------------------
Hier mal meine '/etc/sysconfig/isdn'
-------------------------------------------
#
# /etc/sysconfig/isdn
#
# Called by /etc/rc.d/init.d/isdn4linux
# Called by /etc/sysconfig/network-scripts/ifup-ippp
#
##
### ISDN SYSTEM ######
#
# Set PATH info here, and make sure all scripts sources this file
PATH="/sbin:/usr/sbin:/bin/:/usr/bin"
# Start isdn4linux? ("yes" or "no")
I4L_START="yes"
# Start iprofd ("yes" or "no")
# (re-)store ISDN-modem setup in /etc/isdnlog/modemsettings
# restore automatically at boot-time
# store with "AT&W0" in terminal-emulation
I4L_IPROFD="yes"
# Start isdnlog ("yes" or "no")
# enable isdnlog only after setting up my_isdnlog.conf in /etc/isdn
I4L_ISDNLOG="no"
# Hisax Debug Level, 4 (some..) to 31 (all messages)
I4L_DEBUG=4
# ISDNCTRL verbose level
I4L_VERBOSE=2
# Directory for isdn4net profiles
I4L_PROFILEDIR="/etc/isdn/profile"
# Directory for budget files
I4L_BUDGETDIR="/etc/isdn/budgets"
# Directory for timru files
I4L_TIMRUDIR="/etc/isdn/timru"
# D-channel protocol 1=1TR6, 2=EDSS1(Euro-ISDN) for Teles/HiSax
I4L_PROTOCOL=2
# ISDN CARD config to load
I4L_CARD="mycard"
# Dynamic rewrite of outgoing TCP on open, 0=off 1=on 2=verbose
I4L_DYN=2
-----------------------------------------
hier mal meine mycard-Datei:
-----------------------------------------
# /etc/isdn/profile/card/mycard
#
# Called by /etc/rc.d/init.d/isdn4linux
#
### ISDN CARD #######
# driver-id for ISDN-Card
I4L_ID="HiSax"
# 2. id-string for ICN ISDN-card
# I4L_ID2="ICN2"
# Hisax Debug Level, 4 (some..) to 31 (all messages)
I4L_DEBUG=4
# kernel module to use (teles, hisax, icn, pcbit)
I4L_MODULE="hisax"
# D-channel protocol 1=1TR6, 2=EDSS1(Euro-ISDN) for Teles/HiSax
I4L_PROTOCOL=2
# type of HiSax-driver (set to '' for using old teles-modul or within kernel)
# See below for list of values
I4L_TYPE=5
# IRQ of Teles/HiSax Card
# eg. 12 or 15 when loading as module
# set to "" when driver is loaded within kernel
I4L_IRQ="10"
# Membase of Teles/HiSax card (e.g. '0xd2000' for Teles S0/16,
# '0' for Teles S0/16.3)
I4L_MEMBASE="0xd2000"
# Portaddress of Teles/HiSax card (e.g. 0xd80, "0" for S0/8)
# ORIGINAL I4L_PORT="0xd80"
I4L_Port="0x240"
# for Creatix PNP: IO0 (ISAC)
I4L_IO0=''
# for Creatix PNP: IO1 (HSCX)
I4L_IO1=''
# I4L_TYPE: Card types (info from README.hisax):
#
# Type Required parameters (in addition to type and protocol)
#
# 0 simple 'modprobe hisax' all options taken from /etc/conf.modules
# 1 Teles 16.0 irq, mem, io
# 2 Teles 8.0 irq, mem
# 3 Teles 16.3 (non PnP) irq, io
# 4 Creatix/Teles PnP irq, io0 (ISAC), io1 (HSCX)
# 5 AVM A1 (Fritz) irq, io
# 6 ELSA PCC/PCF cards io or nothing for autodetect (the iobase is
# required only if you have more than one ELSA
# card in your PC)
# 7 ELSA Quickstep 1000 irq, io (from isapnp setup)
# 8 Teles 16.3 PCMCIA irq, io
# 9 ITK ix1-micro Rev.2 irq, io
# 10 ELSA PCMCIA irq, io (set with card manager)
# 11 Eicon.Diehl Diva ISA PnP irq, io
# 11 Eicon.Diehl Diva PCI no parameter
# 12 ASUS COM ISDNLink irq, io (from isapnp setup)
# 13 HFC-2BS0 based cards irq, io
# 14 Teles 16.3c PnP irq, io
# 15 Sedlbauer Speed Card irq, io
# 15 Sedlbauer PC/104 irq, io
# 15 Sedlbauer Speed PCI no parameter
# 16 USR Sportster internal irq, io
# 17 MIC card irq, io
# 18 ELSA Quickstep 1000PCI no parameter
# 19 Compaq ISDN S0 ISA card irq, io0, io1, io (from isapnp setup io=IO2)
# 20 NETjet PCI card no parameter
# 21 Teles PCI no parameter
# 22 Sedlbauer Speed Star (PCMCIA) irq, io (set with card manager)
# 24 Dr. Neuhaus Niccy PnP irq, io0, io1 (from isapnp setup)
# 24 Dr. Neuhaus Niccy PCI no parameter
# 25 Teles S0Box irq, io (of the used lpt port)
# 26 AVM A1 PCMCIA (Fritz!) irq, io (set with card manager)
# 27 AVM PnP (Fritz!PnP) irq, io (from isapnp setup)
# 27 AVM PCI (Fritz!PCI) no parameter
# 28 Sedlbauer Speed Fax+ irq, io (from isapnp setup)
--------------------------------------------
bin für jede Hilfe dankbar
maxxle
Mein Rechner sagt folgendes:
service isdn4linux restart
=>
Shutting down isdn4linux
Shutting down isdn/ippp devices (if any)
Unloading ISDN drivers ...
Starting ISDN for Linux...
Loading HiSax driver
CardID: HiSax
CardType: 5
CardName: AVM A1 (Fritz)
Parameters: id=HiSax type=5 protocol=2 irq=10 io=
Initialization of ISDN failed!
Check parameters in '/etc/sysconfig/isdn'!
Mich wundert ja nur, warum bei io= steht und nicht der Wert 240, so wie ich ihn auch hinterlegt habe in mycard ??
-------------------------------------------
Hier mal meine '/etc/sysconfig/isdn'
-------------------------------------------
#
# /etc/sysconfig/isdn
#
# Called by /etc/rc.d/init.d/isdn4linux
# Called by /etc/sysconfig/network-scripts/ifup-ippp
#
##
### ISDN SYSTEM ######
#
# Set PATH info here, and make sure all scripts sources this file
PATH="/sbin:/usr/sbin:/bin/:/usr/bin"
# Start isdn4linux? ("yes" or "no")
I4L_START="yes"
# Start iprofd ("yes" or "no")
# (re-)store ISDN-modem setup in /etc/isdnlog/modemsettings
# restore automatically at boot-time
# store with "AT&W0" in terminal-emulation
I4L_IPROFD="yes"
# Start isdnlog ("yes" or "no")
# enable isdnlog only after setting up my_isdnlog.conf in /etc/isdn
I4L_ISDNLOG="no"
# Hisax Debug Level, 4 (some..) to 31 (all messages)
I4L_DEBUG=4
# ISDNCTRL verbose level
I4L_VERBOSE=2
# Directory for isdn4net profiles
I4L_PROFILEDIR="/etc/isdn/profile"
# Directory for budget files
I4L_BUDGETDIR="/etc/isdn/budgets"
# Directory for timru files
I4L_TIMRUDIR="/etc/isdn/timru"
# D-channel protocol 1=1TR6, 2=EDSS1(Euro-ISDN) for Teles/HiSax
I4L_PROTOCOL=2
# ISDN CARD config to load
I4L_CARD="mycard"
# Dynamic rewrite of outgoing TCP on open, 0=off 1=on 2=verbose
I4L_DYN=2
-----------------------------------------
hier mal meine mycard-Datei:
-----------------------------------------
# /etc/isdn/profile/card/mycard
#
# Called by /etc/rc.d/init.d/isdn4linux
#
### ISDN CARD #######
# driver-id for ISDN-Card
I4L_ID="HiSax"
# 2. id-string for ICN ISDN-card
# I4L_ID2="ICN2"
# Hisax Debug Level, 4 (some..) to 31 (all messages)
I4L_DEBUG=4
# kernel module to use (teles, hisax, icn, pcbit)
I4L_MODULE="hisax"
# D-channel protocol 1=1TR6, 2=EDSS1(Euro-ISDN) for Teles/HiSax
I4L_PROTOCOL=2
# type of HiSax-driver (set to '' for using old teles-modul or within kernel)
# See below for list of values
I4L_TYPE=5
# IRQ of Teles/HiSax Card
# eg. 12 or 15 when loading as module
# set to "" when driver is loaded within kernel
I4L_IRQ="10"
# Membase of Teles/HiSax card (e.g. '0xd2000' for Teles S0/16,
# '0' for Teles S0/16.3)
I4L_MEMBASE="0xd2000"
# Portaddress of Teles/HiSax card (e.g. 0xd80, "0" for S0/8)
# ORIGINAL I4L_PORT="0xd80"
I4L_Port="0x240"
# for Creatix PNP: IO0 (ISAC)
I4L_IO0=''
# for Creatix PNP: IO1 (HSCX)
I4L_IO1=''
# I4L_TYPE: Card types (info from README.hisax):
#
# Type Required parameters (in addition to type and protocol)
#
# 0 simple 'modprobe hisax' all options taken from /etc/conf.modules
# 1 Teles 16.0 irq, mem, io
# 2 Teles 8.0 irq, mem
# 3 Teles 16.3 (non PnP) irq, io
# 4 Creatix/Teles PnP irq, io0 (ISAC), io1 (HSCX)
# 5 AVM A1 (Fritz) irq, io
# 6 ELSA PCC/PCF cards io or nothing for autodetect (the iobase is
# required only if you have more than one ELSA
# card in your PC)
# 7 ELSA Quickstep 1000 irq, io (from isapnp setup)
# 8 Teles 16.3 PCMCIA irq, io
# 9 ITK ix1-micro Rev.2 irq, io
# 10 ELSA PCMCIA irq, io (set with card manager)
# 11 Eicon.Diehl Diva ISA PnP irq, io
# 11 Eicon.Diehl Diva PCI no parameter
# 12 ASUS COM ISDNLink irq, io (from isapnp setup)
# 13 HFC-2BS0 based cards irq, io
# 14 Teles 16.3c PnP irq, io
# 15 Sedlbauer Speed Card irq, io
# 15 Sedlbauer PC/104 irq, io
# 15 Sedlbauer Speed PCI no parameter
# 16 USR Sportster internal irq, io
# 17 MIC card irq, io
# 18 ELSA Quickstep 1000PCI no parameter
# 19 Compaq ISDN S0 ISA card irq, io0, io1, io (from isapnp setup io=IO2)
# 20 NETjet PCI card no parameter
# 21 Teles PCI no parameter
# 22 Sedlbauer Speed Star (PCMCIA) irq, io (set with card manager)
# 24 Dr. Neuhaus Niccy PnP irq, io0, io1 (from isapnp setup)
# 24 Dr. Neuhaus Niccy PCI no parameter
# 25 Teles S0Box irq, io (of the used lpt port)
# 26 AVM A1 PCMCIA (Fritz!) irq, io (set with card manager)
# 27 AVM PnP (Fritz!PnP) irq, io (from isapnp setup)
# 27 AVM PCI (Fritz!PCI) no parameter
# 28 Sedlbauer Speed Fax+ irq, io (from isapnp setup)
--------------------------------------------
bin für jede Hilfe dankbar
maxxle